Hp Designjet L26500 - Manual 6j1h3h

DESIGNJET L26500 printer series ’s guide

ed from www.Manualslib.com manuals search engine

© 2011 Hewlett-Packard Development Company, L.P. 1st edition

Legal notices

Trademarks

The information contained herein is subject to change without notice.

Microsoft® and Windows® are U.S. ed trademarks of Microsoft Corporation.

The only warranties for HP Products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.


Table of contents

1 Introduction ...................................................................................................................... 1 Safety precautions .................................................................................................................... 1 The printer’s main features ........................................................................................................ 5 The printer’s main components ................................................................................................... 5 The Embedded Web Server .................................................................................................... 10 Turn the printer on and off ....................................................................................................... 11 Restart the printer ................................................................................................................... 12 2 Connectivity and software instructions ............................................................................ 13 Connection method ................................................................................................................ 13 Connect to a network ............................................................................................................. 13 3 Basic setup options ......................................................................................................... 15 Printer setup options ............................................................................................................... 15 Embedded Web Server setup options ....................................................................................... 17 4 Handle the substrate ...................................................................................................... 19 Overview .............................................................................................................................. 19 Porous substrates .................................................................................................................... 23 Load a roll onto the spindle ..................................................................................................... 23 Load a roll into the printer (automatically) ................................................................................. 27 Load a roll into the printer (manually) ....................................................................................... 30 Load a cut sheet into the printer ............................................................................................... 33 Unload a roll from the printer .................................................................................................. 33 The take-up reel ..................................................................................................................... 34 The edge holders ................................................................................................................... 49 The loading accessory ............................................................................................................ 50 Double-sided printing ............................................................................................................. 54 View information about the substrate ........................................................................................ 56 Substrate length tracking ......................................................................................................... 57 Store the substrate .................................................................................................................. 58 5 Substrate settings ........................................................................................................... 59 media presets ........................................................................................................ 59

ENWW


iii

Add a new substrate .............................................................................................................. 59 Faster printing ....................................................................................................................... 70 Color calibration .................................................................................................................... 70 Color profiles ........................................................................................................................ 71 Color reproduction tricks ......................................................................................................... 71 6 Retrieving usage information .......................................................................................... 73 Get ing information ..................................................................................................... 74 Check usage statistics ............................................................................................................. 74 Check usage statistics for a job ................................................................................................ 74 Request ing data by E-mail ........................................................................................... 74 7 The ink system ............................................................................................................... 76 Ink system components ............................................................................................................ 76 Order ink supplies .................................................................................................................. 80 8 Print options ................................................................................................................... 81 Printer states .......................................................................................................................... 81 Change margins .................................................................................................................... 81 Request the printer’s internal prints ........................................................................................... 82 9 Accessories ..................................................................................................................... 83 Order accessories .................................................................................................................. 83 10 Printer specifications ..................................................................................................... 84 Functional specifications ......................................................................................................... 84 Physical specifications ............................................................................................................ 85 Memory specifications ............................................................................................................ 85 Power specifications ............................................................................................................... 85 Environmental specifications .................................................................................................... 86 Acoustic specifications ............................................................................................................ 86 Glossary ............................................................................................................................. 87 Index ................................................................................................................................. 90

iv


ENWW

Introduction

Introduction

1

Safety precautions Before using your printer, read the following safety precautions to make sure you use the equipment safely. You are expected to have the appropriate technical training and experience necessary to be aware of hazards to which you may be exposed in performing a task, and take appropriate measures to minimize the risks to yourself and to other people.

General safety guidelines ●

Refer to the installation instructions before connecting the printer to the supply.

●

There are no operator-serviceable parts inside the printer except those covered by HP's Customer Self Repair program (see http://www.hp.com/go/selfrepair/). Refer servicing of other parts to qualified service personnel.

●

Turn off the printer, unplug both power cords from the power outlets, and call your service representative in any of the following cases.

●

◦

The power cord or plug is damaged.

◦

Liquid has entered the printer.

◦

There is smoke or an unusual smell coming from the printer.

◦

The printer has been dropped or the drying or curing module damaged.

◦

The printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) has been repeatedly tripped.

◦

The printer is not operating normally.

Turn off the printer and unplug both power cords from the power outlets in either of the following cases. ◦

During a thunderstorm

◦

During a power failure

Electrical shock hazard WARNING! The drying and curing modules operate at hazardous voltages capable of causing death or serious personal injury.

ENWW


Safety precautions

1

Introduction

The printer uses two power cords. Unplug both power cords before servicing the printer. The printer must be connected to earthed mains outlets only. To avoid the risk of electric shock: ●

Do not attempt to dismantle the drying and curing modules or the electrical control cabinet.

●

Do not remove or open any other closed system covers or plugs.

●

Do not insert objects through slots in the printer.

●

Test the functionality of the Residual Current Circuit Breaker (RCCB) every 6 months.

Heat hazard The drying and curing subsystems of the printer operate at high temperatures and can cause burns if touched. To avoid personal injury, take the following precautions. ●

Do not touch the internal enclosures of the printer's drying and curing modules. Even after opening the window latch that disconnects drying and curing power, the internal surfaces could be hot.

●

Take special care when accessing the substrate path.

Fire hazard The drying and curing subsystems of the printer operate at high temperatures. Call your service representative if the printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) is repeatedly tripped. To avoid the risk of fire, take the following precautions.

2

●

Use the power supply voltage specified on the nameplate.

●

Connect the power cords to dedicated lines, each protected by a branch circuit breaker according to the rating of the wall socket. Do not use a power strip (relocatable power tap) to connect both power cords.

●

Use only the power cords supplied by HP with the printer. Do not use a damaged power cord. Do not use the power cords with other products.

●

Do not insert objects through slots in the printer.

●

Take care not to spill liquid on the printer.

●

Do not use aerosol products that contain flammable gases inside or around the printer.

●

Do not block or cover the openings of the printer.

●

Do not attempt to dismantle the drying or curing module, or the electrical control cabinet.

●

Ensure that the operating temperature of the substrate loaded recommended by the manufacturer is not exceeded. If this information is not available from the manufacturer, do not load substrates that cannot be used at an operating temperature under 125°C (257°F).

●

Do not load substrates with auto-ignition temperatures below 300°C (572°F). See note below.

Chapter 1 Introduction


ENWW

Introduction

NOTE: Test method based on EN ISO 6942:2002; Evaluation of materials and material assemblies when exposed to a source of radiant heat, method B. The test conditions, to determine the temperature when the substrate starts ignition (either flame or glow) were: Heat flux density: 30 kW/m², copper calorimeter, K type thermocouple.

Mechanical hazard The printer has moving parts that could cause injury. To avoid personal injury, take the following precautions when working close to the printer. ●

Keep your clothing and all parts of your body away from the printer's moving parts.

●

Avoid wearing necklaces, bracelets and other hanging objects.

●

If your hair is long, try to secure it so that it will not fall into the printer.

●

Take care that sleeves or gloves do not get caught in the printer's moving parts.

●

Avoid standing close to the fans, which could cause injury and could also affect print quality (by obstructing the air flow).

●

Do not touch gears or moving rolls during printing.

Heavy substrate hazard Special care must be taken to avoid personal injury when handling heavy substrates. ●

Handling heavy substrate rolls may require more than one person. Care must be taken to avoid back strain and/or injury.

●

Consider using a forklift, pallet truck or other handling equipment.

●

When handling heavy substrate rolls, wear personal protective equipment including boots and gloves.

Ink handling Your printer does not use solvent inks and does not have the traditional problems associated with them. However, HP recommends that you wear gloves when handling ink system components.

Warnings and cautions The following symbols are used in this manual to ensure the proper use of the printer and to prevent the printer from being damaged. Follow the instructions marked with these symbols. WARNING! Failure to follow the guidelines marked with this symbol could result in serious personal injury or death. CAUTION: Failure to follow the guidelines marked with this symbol could result in minor personal injury or damage to the product.

ENWW


Safety precautions

3

Introduction

Warning labels Label

Explanation Risk of burns. Do not touch the internal enclosures of drying and curing modules of the printer.

Risk of burns. Do not touch the drying enclosure of the printer. Even after opening the window latch, which disconnects the power to the drying and curing modules, the internal surfaces could be hot. Electric shock hazard. The printer has two input power cords. A voltage is still present in the drying and curing modules after the main switch is turned off. There are no operatorserviceable parts inside the printer. Refer servicing to qualified service personnel. Disconnect all power cords before servicing. See installation instructions before connecting to the supply. Ensure that the input voltage is within the printer's rated voltage range. The printer requires two dedicated lines, each protected by a branch circuit breaker according to the rating of the wall socket outlet. Use only earthed mains outlets and the power cords supplied by HP with the printer. Risk of trapped hands. Do not push the roll while loading. Lift the loading table to ease the spindle into the printer.

Risk of trapped fingers. Do not touch spindle gears while moving.

Do not put objects on top of the printer. Do not cover the top fans.

You are recommended to wear gloves when handling ink cartridges, printhead cleaning cartridges and the printhead cleaning container.

4



ENWW

Introduction

The printer’s main features Your printer is a color inkjet printer designed for printing high-quality images on flexible substrates from 0.584 m (23 in) to 1.55 m (61 in) wide. Some major features of the printer are shown below: ●

Printing speeds in draft mode of up to 22.8 m²/h (246 ft²/h).

●

Environmentally friendly, odorless, aqueous latex inks in six colors

●

No special ventilation required, no hazardous waste

●

775 ml ink cartridges

●

Print on a wide range of substrates—including most low-cost, uncoated, solvent-compatible substrates

●

A range of HP recyclable substrates is available

●

Durable prints with outdoor display permanence up to three years unlaminated, five years laminated

●

Accurate and consistent color reproduction with automatic color calibration (built-in spectrophotometer) for most substrates

●

ENERGY STAR® qualified product

To send print jobs to your printer, you will need Raster Image Processor (RIP) software, which should be run on a separate computer. RIP software is available from various different companies; it is not provided with the printer.

The printer’s main components The following views of the printer illustrate its main components.

ENWW


The printer’s main features

5

Introduction

Front view

1.

Ink cartridge

2.

Platen

3.

Printhead

4.

Printhead carriage

5.

Ink funnel and ink tube assembly

6.

Front

7.

Printhead cleaning cartridge

8.

Substrate-adjustment lever

9.

Spindle lock lever

10. Take-up reel motor 11. Take-up reel cable and sensor housing unit 12. Spindle 13. Loading table/take-up reel deflector 14. Drying module 15. Take-up reel sensor 16. Take-up reel spindle stop 17. Loop-shaper 18. Curing module

6



ENWW

1.

Printhead cleaning container

2.

Sockets for communication cables and optional accessories

3.

Power switch and power sockets

4.

Residual current circuit breakers for the heating components

5.

Ink filter

Introduction

Rear view

Edge holders case

ENWW


The printer’s main components

7

Introduction

The case is normally attached to the rear of the printer, and contains the two edge holders when they are not in use.

Drying enclosure

Take-up reel motor

8

1.

Take-up reel spindle lever

2.

Wind-direction switch

3.

Manual winding buttons



ENWW

Introduction

Loading accessory

The loading accessory helps you to load some substrate types that are difficult to load without it. See The loading accessory on page 50.

The front Your printer's front is located at the front right of the printer. It has the following important functions: ●

Assists you in troubleshooting issues

●

Is used when performing certain physical operations, such as unloading substrate and maintaining the printer

●

Displays information in brief about the status of the printer

●

Displays warning and error messages, when appropriate, along with audio alerts to call attention to a warning or message

The front has the following components: 1.

Power key: To turn the printer off. See Turn the printer on and off on page 11.

2.

Power light: Indicates the printer's power status. If the light is off, the printer is off. If it is solid green, the printer is on. If it is flashing green, the printer is in transition between on and off.

3.

Front- display: Displays error, warnings and information on using your printer.

4.

Status light: Indicates the printer's operational status. If the light is off, the printer is not ready. If it is solid green, the printer is ready and idle. If it is flashing green, the printer is busy: receiving data, processing or printing. If it is flashing amber, your intervention is required. If it is solid amber, a serious error has occurred.

ENWW


The printer’s main components

9

Introduction

5.

Up key: To go up in a menu or option, or to increase a value.

6.

OK key: To confirm an action while in a procedure or interaction. To enter in a submenu in the menu. To select a value when given an option.

7.

Down key: To go down in a menu or option, or to decrease a value.

8.

Back key: To go to the previous step in a procedure or interaction. To go to the upper level, or leave the option in the menu, or when given an option.

9.

Cancel key: To cancel a procedure or interaction.

10. Reset key: To restart the printer (as if it were switched off and switched on again). You will need an implement with a narrow tip to operate this key. 11. Move substrate key: To move the loaded substrate forwards or backwards. While the printer is printing, it can be used to fine-tune the substrate advance on the fly. To highlight an item in the front- display, press the Up or Down key until the item is highlighted. To select an item in the front- display, first highlight it and then press the OK key. When this guide shows a series of front- display items like this: Item1 > Item2 > Item3, it means that you should select Item1, then select Item2, then select Item3. Information about specific uses of the front can be found throughout this guide.

The Embedded Web Server The Embedded Web Server is a Web server running inside the printer. You can use it to obtain printer information, manage settings and presets, align printheads, new firmware and troubleshoot problems. Service engineers can use it to retrieve internal information that helps to diagnose printer problems. You can access the Embedded Web Server remotely by using an ordinary Web browser running on any computer. See Access the Embedded Web Server on page 17. The Embedded Web Server window displays three separate tabs. Buttons near the top of each page provide access to online help and supplies reordering.

10



ENWW

Introduction

Main tab The Main tab provides information about the following items. ●

Substrate, ink, printhead and maintenance status

●

Temperatures of the drying and curing modules

●

Substrate and ink usage and ing

Setup tab The Setup tab enables you to complete these tasks. ●

Specify printer settings such as units of measurement and refresh date

●

Specify network and security settings

●

Set the date and time

●

Update firmware

●

Align printheads

●

media presets

tab The tab offers various kinds of help with your printer. ●

Browse helpful information from a variety of sources

●

Troubleshoot problems

●

Access HP Designjet links for technical with your printer and accessories

●

Access service pages that show current and historical data on the usage of your printer

Turn the printer on and off To turn on the printer, ensure that the power switch at the rear of the printer is turned on, ensure that the residual current circuit breakers are in the up position, then press the Power button on the front . You can leave the printer on without wasting energy. Leaving it on improves response time. When the printer has not been used for a certain period of time, it saves power by going into sleep mode. Any interaction with the printer returns it to active mode, and it can resume printing immediately. If you want to turn the printer on or off, the normal and recommended method is to use the Power button on the front .

ENWW


Turn the printer on and off

11

Introduction When you turn off the printer this way, the printheads are automatically stored with the printhead cleaning cartridge, which prevents them from drying out. However, if you plan to leave the printer turned off for a long period of time, you are recommended to turn it off using the Power button, and then also turn off the power switch at the rear.

To turn it back on later, use the power switch at the rear, and then press the Power button. When the printer is turned on, it takes about 5 minutes to initialize itself.

Restart the printer In some circumstances you may be advised to restart the printer. Please proceed as follows:

12

1.

Press the Power button on the front to turn the printer off. Wait a few moments, then press the Power button again. This should restart the printer. If it does not, continue with step 2.

2.

Use the Reset button on the front . You will need a non-conductive implement with a narrow tip to press the Reset button. This normally has the same effect as pressing the Power button, but may work if the Power button does not.

3.

If neither steps 1 nor 2 seems to have any effect, turn off the printer by using the power switch at the rear of the printer. Check that the residual current circuit breakers are in the up position.

4.

Remove the power cords from the power sockets.

5.

Wait for 10 seconds.

6.

Reinsert the power cords into the power sockets and turn on the printer by using the power switch.

7.

Make sure that the Power light on the front illuminates. If it does not, use the Power button to turn on the printer.



ENWW

Connectivity and software instructions

Connectivity

2

Connection method Your printer can be connected in the following way. Connection type

Speed

Maximum cable length

Other factors

Gigabit Ethernet

Fast; varies according to network traffic

Long (100 m=328 ft)

Requires extra equipment (switches)

NOTE: The speed of any network connection depends on all the components that are used in the network, which can include network interface cards, hubs, routers, switches, and cables. If any one of these components cannot operate at high speed, you will have a low-speed connection. The speed of your network connection can also be affected by the total amount of traffic from other devices on the network.

Connect to a network Before you begin, check your equipment: ●

The printer should be set up and turned on.

●

The Gigabit switch or router should be on and functioning correctly.

●

All computers on the network should be turned on and connected to the network.

●

The printer should be connected to the switch.

When the printer is connected to the network and turned on, you should see the printer's IP address appear on the front (192.168.1.1 in this example). Make a note of the IP address: you can use it later to access the Embedded Web Server.

ENWW


Connection method

13

Connectivity

If you see this screen without the IP address, either the printer is not successfully connected to the network, or your network has no DH server. In the latter case, you will have to set the IP address manually: see the Maintenance and troubleshooting guide. Refer to the RIP instructions (not provided by HP) to install the software RIP.

14

Chapter 2 Connectivity and software instructions


ENWW

3

Basic setup options

Printer setup options Change the language of the front

●

If you can understand the current front language, go to the front and select the icon, then select Front options > Select language.

●

If you cannot understand the current front language, start with the printer powered off. At the front , press the OK button and hold it down. While holding down the OK button, press the Power button and hold it down. Continue to hold down both buttons until the green light on the left side of the front starts flashing, then release both buttons. You can expect a delay of about one second. If the green light starts flashing without any delay, you may need to start again.

Whichever method you used, the language selection menu should now appear on the front .

Highlight your preferred language, then press the OK button.

View or set the date and time To view or set the printer's date and time, go to the front and select the options > Date and time options.

icon, then Front

Set altitude If your printer is operating at a significant altitude above sea level, go to the front and select the icon, then Select altitude, to tell the printer its operating altitude.

ENWW


Printer setup options

15

Basic setup options

Two methods are available to change the language that is used for the front- menus and messages.

Request e-mail notification of specific error conditions 1.

In the Embedded Web Server, go to the E-mail server page on the Setup tab and ensure that the following fields are correctly filled in: ●

SMTP server. This is the IP address of the outgoing mail server (Simple Mail Transfer Protocol [SMTP]) that processes all e-mail messages from the printer. If the mail server requires authentication, e-mail notifications will not work.

●

Printer e-mail address. Each e-mail message that the printer sends must include a return address. This address does not need to be a real, functional e-mail address, but it should be unique, so that recipients of the message can identify the printer that sent it

2.

Go to the Notification page, which is also on the Setup tab.

3.

Click the New icon to request new notifications, or click the Edit icon to edit notifications that have already been set up. Then specify the e-mail addresses to which notifications are sent, and select the incidents that result in notification messages.

Change the cool-down delay Basic setup options

When there are no more jobs to print, the printer's drying and curing heaters remain on for a while, in case another job arrives. To choose how long they remain switched on in this situation, go to the front icon, then Substrate handling options > Cooldown wait when idle. and select the Select a time from 5 to 60 minutes, then press the OK button.

Change the sleep mode setting If the printer is left turned on but unused for a certain period of time, it automatically goes into sleep mode to save power. The default period of time it waits is 30 minutes. To change the time the printer icon, then select Front waits before it goes into sleep mode, go to the front and select the options > Sleep mode wait time. Highlight the wait time that you want, then press the OK button.

Turn the buzzer on or off To turn the printer's buzzer on or off, go to the front and select the then on or off. By default, the buzzer is on.

icon, then Audio alert,

Change the front display contrast To change the contrast of the front- display, select the icon, then Front options > Select display contrast, then select a value by using the Up or Down button. Press the OK button to save the value.

Change the units of measurement To change the units of measurement that appear on the front , select the options > Select units, then English or Metric.

icon, then Front

The units of measurement can also be changed in the Embedded Web Server.

16

Chapter 3 Basic setup options


ENWW

Restore factory settings To restore the printer settings to their original values as set in the factory, go to the front and icon, then Resets > Restore factory settings. This option restores all of the printer select the settings except the Gigabit Ethernet settings. To restore the Gigabit Ethernet factory settings, select the Ethernet > Restore factory settings.

icon, then Connectivity > Gigabit

Embedded Web Server setup options Access the Embedded Web Server Use the Embedded Web Server to view printer information remotely through an ordinary Web browser running on any computer.

●

Internet Explorer 6 and later for Windows

●

Safari 2 and later for Mac OS X

●

Mozilla Firefox 2 and later

●

Google Chrome 7

Basic setup options

The following browsers are known to be compatible with the Embedded Web Server:

To use the Embedded Web Server on any computer, open your Web browser and type the printer's URL. The printer's URL appears on the status screen on the printer's front (http://192.168.1.1 in this example):

If you follow these instructions but fail to open the Embedded Web Server, see the Maintenance and troubleshooting guide.

Change the language of the Embedded Web Server The Embedded Web Server functions in the following languages: English, Portuguese, Spanish, Catalan, French, Italian, German, Simplified Chinese, Traditional Chinese, Korean, and Japanese. It uses the language that you specified in your Web browser options. If you specify a language that it cannot , it functions in English. To change the language, change your Web browser's language setting. For example, in Internet Explorer version 6, go to the Tools menu and select Internet Options > Languages. Make sure that the language you want is at the top of the list in the dialog box. To complete the change, close and reopen your Web browser.

ENWW


Embedded Web Server setup options

17

Restrict access to the printer From the Embedded Web Server, you can select Setup > Security to set an . Once set, this must be given in order to perform the following printer functions. ●

Change printer settings.

●

Update the firmware.

●

Change the printer's date and time.

●

Clear ing information.

For more information, see the Embedded Web Server's online help. If you forget the , you can delete the current from the front : select the icon, then Connectivity > Advanced > Embedded Web Server > Reset EWS .

Basic setup options 18

Chapter 3 Basic setup options


ENWW

4

Handle the substrate

Overview You can print on a wide variety of printing materials, all of which are referred to in this guide as substrates.

Substrate tips Choosing the correct substrate for your needs is an essential step in ensuring good print quality.

●

Allow all substrates to adapt to room conditions, out of the packaging, for 24 hours before using them for printing.

●

Handle film and photo substrates by the edges, or wear cotton gloves. Skin oils can be transferred to the substrate, leaving fingerprint marks.

●

Keep the substrate tightly wound on the roll throughout the loading and unloading procedures. To make sure that the roll stays tightly wound, consider using tape to stick the leading edge of the roll to the core just before removing the roll from the printer. You can keep the roll taped during storage. If the roll starts to unwind, it can become difficult to handle. NOTE: The use of tape to stick the leading edge of the roll to the core is especially important for heavy substrates, because the inherent stiffness of the substrate can cause it to loosen and unwind from the core.

●

Using the take-up reel gives the printer better control of the substrate and is likely to improve print quality.

●

Print quality could be impaired if you use a substrate that is unsuitable for your image.

●

Make sure that the appropriate print-quality setting is selected in the RIP.

●

Whenever you load a roll, the front prompts you to specify the substrate family that you are loading. For good print quality, it is essential to specify this correctly. Check that the substrate

ENWW


Overview

19


Here are some tips about substrate usage.

belongs to the family named on the front , and check also that it matches the substrate profile in the RIP. ●

If the substrate family shown on the front does not correspond to the substrate that you have loaded, take one of the following actions: ◦

Reload the roll into the printer and select the correct substrate family. See Unload a roll from the printer on page 33 and Load a roll into the printer (automatically) on page 27.

◦

At the printer's front , select the Change loaded substrate.

icon, then select View loaded substrate >

NOTE: Substrate advance calibration is not performed when the substrate family is changed from the front . CAUTION: Removing the substrate from the printer manually without using the front could damage the printer. Do this only when necessary to clear a substrate jam.

ed substrate families Substrate family

Description

Self-adhesive

Printable PVC films with adhesive on one side and a detachable liner. There are two main vinyl types classified by manufacturing process and application purpose: calendered (for flat surfaces) and cast (for complex 3D curves). The film may have different finishes: white, finished, transparent, reflective or perforated. Perforated substrates may need manual rather than automatic printhead alignment. Examples: HP Air Release Adhesive Gloss Cast Vinyl, Avery MPI3000 (calendered), Avery MPI1005 (cast), 3M IJ-380 (cast)

Banner

Usually a polyester mesh (which provides mechanical resistance) coated with PVC. There are also recyclable versions to cover the same applications (green banners). Banners have a wide range of grammage and can be grouped into frontlit, backlit and block-out categories. Examples: HP Durable Frontlit Scrim Banner, Ultraflex Normandy Pro, Verseidag banners


Textile

Printable textile substrates are usually made of polyester or cotton yarns. Some open or light textile substrate types come with a removable liner to prevent the ink from ing through the substrate. Textile materials that are very stiff (such as canvases) should preferably be loaded as “Low-temp." substrate. These substrates may need manual rather than automatic printhead alignment.

Film

Usually a polyester film, although there are other materials such as PVC or PC. Generally these substrates are used for backlit applications. Select this family setting for substrates that resist temperatures over 95°C (200°F), otherwise load them preferably as "Low-temp." substrate. These substrates may need manual rather than automatic printhead alignment. Example: Intelicoat SBL-7 Polyester Backlit Film

Synthetic paper

Substrates manufactured using synthetic resins, mainly extruded from polypropylene (PP). They have characteristics similar to those of plastic film, but their appearance and properties are similar to regular paper made from wood pulp. Examples: Yupo FEB 250, Ilford Omnijet Dry Glossy Portable Display Film

Paper-aqueous

Light paper-based (cellulose) substrates with a coating compatible with water-based inks, or offset paper. These substrates are not compatible with solvent inks. Weight is usually around 100 g/m². Example: HP Heavyweight Coated Paper

Paper-solvent

Paper-based (cellulose) substrates with a top-coating compatible with solvent inks. Weight is usually between 120 and 200 g/m². Examples: HP Blue Back Billboard Paper, Intelicoat GPIOF140, blue back substrates

20

Chapter 4 Handle the substrate


ENWW

Substrate family

Description

Low-temp. (including HP Photorealistic)

Substrates sensitive to high temperatures (PP, HDPE, PET thin films), and paper-based (cellulose) substrates with top-coating that have a high stiffness and grammage (200 g/m² or higher). Example: HP Photorealistic Poster Paper

Mesh

An open and resistant polyester mesh coated with PVC and mainly used for building wrap applications. Some of these substrates have a removable liner to prevent the ink from ing through the substrate. These substrates may need manual rather than automatic printhead alignment. Example: Ultraflex Stripmesh

Must be used with the 2 inch spindle (see Accessories on page 83) The Latex Media Finder is a tool that allows you to search for substrates (HP and third-party) that have been tested and shown to be compatible with your printer. The tool allows searching by manufacturer brand, substrate type, application or geographical availability. It can be found at http://www.hp.com/go/latexmediafinder/.

ed HP substrates Substrate

2 inch

Re cycle

Take Back

Color Pro

FSC®

PEFC

Oeko

Banners HP HDPE Reinforced Banner HP Double-sided HDPE Reinforced Banner HP Durable Frontlit Scrim Banner


HP Everyday Matte Polypropylene HP Durable Semi-gloss Display Film Self-adhesive materials HP Air Release Adhesive Gloss Cast Vinyl HP One-view Perforated Adhesive Window Vinyl HP Permanent Gloss Adhesive Vinyl HP Permanent Matte Adhesive Vinyl HP Everyday Adhesive Matte Polypropylene Films HP Backlit Polyester Film Fabrics HP Heavy Textile Banner

•

HP Light Textile Display Banner

•

Papers HP PVC-free Wall Paper (Greenguard, AgBB)

ENWW


Overview

21

Substrate

2 inch

Re cycle

Take Back

Color Pro

FSC®

PEFC

Oeko

HP White Satin Poster Paper HP Photo-realistic Poster Paper HP Blue Back Billboard Paper HP Coated Paper

•

HP Universal Coated Paper

•

HP Universal Heavyweight Coated Paper

•

HP Heavyweight Coated Paper

• •

HP Universal Bond Paper

•

HP Super Heavyweight Plus Matte Paper Specialty materials HP DuPont Tyvek Banner HP Satin Canvas HP Collector Satin Canvas

Key Must be used with the 2 inch spindle (see Accessories on page 83) Recycle: Substrates that can be recycled through commonly available recycling programs.


TakeBack: HP offers the HP Large-format Media TakeBack program in North America and Europe through which most HP recyclable substrates can be returned, availability varies. For details, visit http://www.hp.com/recycle/. Aside from this program, recycling opportunities for these products are currently only available in limited areas. Customers should consult local recycling resources for recycling these products. Papers bearing the ColorPRO logo are manufactured to meet a strict set of quality specifications, with performance criteria such as black optical density, color gamut line edge acuity and color-to-color bleed. The performance and quality of ColorPRO papers are verified by an independent testing agency.

FSC®-certified papers carry the Forest Stewardship Council® (FSC) Mixed Sources label, signifying that these substrates the development of responsible forest management worldwide. The wood comes from FSC®-certified well-managed forests, company-controlled sources and/or recycled material.

22



ENWW

The Program for the Endorsement of Forest Certification label demonstrates that certified HP papers come from forests that are managed sustainably.

Unprinted HP Heavy Textile Banner, HP Light Textile Display Banner and HP Wrinklefree Flag with Liner are Oeko-Tex-certified according to Oeko-Tex Standard 100, which is a globally uniform testing and certification system for textile raw materials, intermediate and end products at all stages of production. Tested for emissions of chemicals such as pesticides, allergy-inducing dyestuffs or tin-organic compounds.

Greenguard

HP PVC-free Wall Paper printed using HP Latex Inks is listed in the GREENGUARD product list of low-emitting products and is tested to the GREENGUARD Children & Schools standard. The print is neither GREENGUARD nor GREENGUARD Children & Schools Certified. The GREENGUARD Environmental Institute is an American National Standards Institute (ANSI) authorized standards developer that establishes acceptable indoor air standards for indoor products, environments, and buildings. See http://www.greenguard.org/.

AgBB

The Committee for Health-related Evaluation of Building Products, AgBB, establishes the fundamentals for a uniform and reproducible health-related evaluation of building products in , including criteria for testing and an evaluation scheme for healthrelated evaluation of volatile organic compound (VOC) emissions from building products used for application indoors.

Porous substrates Substrates of limited porosity may be used with this printer, but very porous substrates could damage the printer.


To check the porosity of your substrate, see the Maintenance and troubleshooting guide. If you use a substrate that is too porous, or fail to clean the platen as recommended, you could experience a decrease in print quality that would require a service repair not covered by your warranty.

Load a roll onto the spindle 1.

Make sure that the printer wheels are locked (the brake lever is pressed down) to prevent the printer from moving.

ENWW


Porous substrates

23

2.

Lift the spindle lock lever to disengage the spindle.

3.

Remove the first end of the spindle from the right side of the printer, then move the spindle to the right in order to extract the other end. Do not insert your fingers into the spindle s during the removal process.


The spindle has a stop at each end to keep the roll in position. Remove the blue stop at the left end to mount a new roll (the stop at the other end can also be removed, if you wish). The stop slides along the spindle to hold rolls of different widths. 4.

24

Slide the lever-lock on the blue stop to the unlocked position.



ENWW

Remove the stop from the left end of the spindle.

6.

Rest the roll of substrate that you want to load on the loading table. If the roll is long and heavy, you may need two people to handle it.

7.

Slide the spindle into the roll.


5.

ENWW


Load a roll onto the spindle

25

8.

The right stop of the spindle has two positions: one for rolls of the printer's maximum width, and another for narrower rolls. to use the second position for narrower rolls, which improves the drying process and allows higher printing speeds.

9.

Put the blue stop on to the upper end of the spindle, and push it towards the end of the roll.


TIP: If the cardboard core of the substrate is longer than the substrate, you can load the substrate without inserting the blue stop, but care should be taken when unloading the substrate, as the loading/unloading table is designed to be used with the blue stop in place. TIP: When loading a roll that is 1549 mm (61 in) wide, you may find it easier to load without stops (remove both stops). 10. Slide the lever-lock to the locked position.

26



ENWW

11. Lift the loading table to ease the spindle into the printer. CAUTION:

To avoid trapping your fingers, do not push the roll with your hands.

If you regularly use different substrates, you can change rolls more quickly if you pre-load rolls of different substrates on different spindles. Extra spindles are available for purchase.

Load a roll into the printer (automatically) To start this procedure, you need to have a roll loaded on the spindle. See Load a roll onto the spindle on page 23. The normal minimum substrate width is 23 inches (584 mm). To load substrates down to a minimum width of 10 inches (254 mm), go to the front and select the icon, then select Substrate handling options > Enable narrow substrate. With this option, print quality is not guaranteed. TIP: To load a roll of textile material, see The loading accessory on page 50. TIP: When loading very thin or very thick substrates, or substrates with a tendency to curl, you should follow the manual loading procedure to reduce the risk of substrate jams and printhead crashes; see Load a roll into the printer (manually) on page 30. At the printer's front , select the

icon, then select Substrate load > Load roll.


1.

ENWW


Load a roll into the printer (automatically)

27

2.

Carefully insert the leading edge of the substrate above the black-ribbed roller, making sure the substrate remains taut during the process. Avoid rewinding the substrate manually, unless the printer asks you to do so.

WARNING! Take care not to touch the rubber wheels on the platen while loading substrate. These wheels can rotate and trap skin, hair or clothing. WARNING! Take care not to push your fingers inside the printer's substrate path. The printer beeps when it detects and accepts the leading edge of the substrate. 3.

The front may prompt you to remove the edge holders from the platen, if the printer believes they are present (it may be wrong: it has no sensor to detect them).

4.

Select the type of substrate you are loading.


NOTE: You should select the name of the particular substrate that you are using in your RIP software, not in the front . NOTE: The RIP substrate setting will overwrite the front setting. 5.

28

If the roll of substrate you are loading is new, select the length in the front . If the substrate has been used before, and the tracking feature was used, select the substrate remaining. For information on the substrate length tracking feature see Substrate length tracking on page 57



ENWW

6.

The printer checks the substrate in various ways and may ask you to correct problems with skew or tension. NOTE: You can specify the maximum permitted amount of skew at the front : select the icon, then select Substrate handling options > Max skew setting.

7.

Wait until the substrate emerges from the printer, as shown below.

NOTE: If you have an unexpected problem at any stage of the substrate loading process, see the Maintenance and troubleshooting guide. 8.

If you are loading transparent substrate without opaque borders, you are asked to enter the width of the substrate and the distance of the right edge from the printer's side plate (as indicated by the ruler on the front of the curing module).

9.

If you have chosen double-sided printing, the front may ask a question about it at this point.

10. The printer calibrates the substrate advance.


11. The printer indicates that it is ready for printing.

Take care not to cover the top fans.

ENWW


Load a roll into the printer (automatically)

29

For instructions on how to use the take-up reel see The take-up reel on page 34.

Load a roll into the printer (manually) The manual loading process should be used in the following cases: ●

The substrate is unusually thin or unusually thick.

●

The substrate has ragged edges.

●

The substrate tends to curl at the edges.

●

The printing side of the substrate faces outwards.

In other cases, the automatic loading process is recommended: see Load a roll into the printer (automatically) on page 27. To start this procedure, you need to have a roll loaded on the spindle. See Load a roll onto the spindle on page 23. The normal minimum substrate width is 23 inches (584 mm). To load substrates down to a minimum width of 10 inches (254 mm), go to the front and select the icon, then select Substrate handling options > Enable narrow substrate. With this option, print quality is not guaranteed. TIP: To load a roll of textile material see The loading accessory on page 50. 1.

At the printer's front , select the

icon, then select Substrate load > Manual load.


This step is optional: you can alternatively begin at step 2. The front may prompt you to remove the edge holders from the platen, if the printer believes they are present (it may be wrong: it has no sensor to detect them). 2.

30

Lift the substrate-adjustment lever as far up as it will go.



ENWW

3.

Carefully insert the leading edge of the substrate above the black-ribbed roller, making sure the substrate remains taut during the process. Avoid rewinding the substrate manually, unless the printer asks you to do so. The front displays the following.

4.

Continue to feed the substrate until it reaches the printing platen. Open the window to help pull the substrate through. WARNING! Do not touch the printer's drying enclosure. Even after you have opened the window latch, which disconnects the power to the drying and curing modules, the internal surfaces could be hot. TIP: If the substrate you are using tends to curl, keep feeding the substrate until the edge is out of the printer. You are also recommended to use the take-up reel, or to disable the cutter from the front if not using the take-up reel. Pull down the substrate-adjustment lever as far as it will go.


5.

ENWW


Load a roll into the printer (manually)

31

6.


NOTE: You should select the name of the particular substrate that you are using in your RIP software, not in the front . TIP: When loading very thin substrates, always select the substrate type as Banner to minimize the vacuum pressure applied while loading; when loading very thick substrates, always select the substrate type as HP Photorealistic to maximize the vacuum pressure. After loading and before printing, go to the front and change to the correct type for the substrate you are loading: icon, then select View loaded substrate > Change loaded substrate. select the TIP: When manually loading textile substrates that you intend to use with the take-up reel, before selecting the substrate type it is a good idea to press the Move substrate key on the front and use the front to advance the substrate beyond the point where it may jam in the printer. This avoids the possibility of a substrate jam at this stage and also some other substrate issues; and it enables you to skip the normal check for skew. 7.

The printer checks the substrate in various ways and may ask you to correct problems with skew or tension. NOTE: You can specify the maximum permitted amount of skew at the front : select the icon, then select Substrate handling options > Max skew setting.


8.

If you are loading transparent substrate without opaque borders, you are asked to enter the width of the substrate and the distance of the right edge from the printer's side plate (as indicated by the ruler on the front of the curing module).

9.

If you have chosen double-sided printing, the front may ask a question about it at this point.

10. The printer calibrates the substrate advance. 11. The printer indicates that it is ready for printing.

Take care not to cover the top fans.

32



ENWW

Load a cut sheet into the printer

●

The sheet should be at least 1067 mm (42 in) long.

●

Load the sheet by following the normal roll loading process (automatic or manual, depending on the substrate).

●

During the loading process, the printer tries to detect the winding direction of the roll by turning the spindle in both directions. When the substrate is not attached to the spindle, the following message appears.

To continue loading, select Skip check – would affect IQ. ●

A cut sheet is likely to be loaded with excessive skew, and the printer may not be able to correct it automatically. If the skew as measured by the printer exceeds 3 mm/m, you are recommended to stop loading and try again. However, if the skew is tolerable, you can consider skipping the automatic skew correction. To do so, when prompted, choose Continue with current skew.

Unload a roll from the printer 1.

If you used the take-up reel during printing, unload the printed roll from the take-up reel. See Unload a roll from the take-up reel on page 47.

2.

On the printer's front , select the

3.

Press the OK button on the front as many times as needed to rewind the substrate.

4.

Lift the spindle lock lever.

ENWW


icon, then select Substrate unload > Unload roll.

Load a cut sheet into the printer

33


The printer is designed to be used with rolls of substrate. It is possible to load cut sheets into the printer, but print quality cannot be guaranteed, and you may have some difficulty in avoiding skew.

5.

Remove the roll from the printer, pulling out the right end on the right side of the printer first. Do not insert your fingers into the spindle s during the removal process.

The take-up reel The take-up reel must be enabled and operated from the front . When the take-up reel is enabled, the “Take-up reel enabled” message appears on the Substrate tab on the front . If the take-up icon, then select Take-up reel > reel is not enabled and you would like to enable it, select the Enable take-up reel.

The loop-shapers When in use, the take-up reel requires a dangling loop of substrate weighed down by a loop shaper. There are two different loop-shapers provided with the printer, to be used with different substrate types. ●

The heavy loop-shaper is used with banner, textile and mesh substrates. It is attached to s on either side of the substrate. The spindle stops should not be used with this loop-shaper.

Handle the substrate 34



ENWW

●

The light loop-shaper is used with all other substrates. It lies in the substrate loop, ed only by the substrate, unattached at either end. It should be the same width as the substrate; therefore, it is supplied in sections of different widths that can be fitted together. The spindle stops should be used with this loop-shaper.

There are two slightly different procedures for loading a roll onto the take-up reel, depending on which substrate type and therefore which loop-shaper is used: see See Load a roll onto the take-up reel (banner/textile/mesh substrates) on page 35 and Load a roll onto the take-up reel (other substrates) on page 41.

Load a roll onto the take-up reel (banner/textile/mesh substrates) 1.

On the printer's front , select the reel.

2.

The front offers you the choice of loading the take-up reel immediately, or during printing.


icon, then select Take-up reel > Enable take-up

If you decide to load the take-up reel during printing, familiarize yourself with the procedural steps. Loading the take-up reel during printing requires you to complete the procedure while the printer is feeding and printing substrate. Loading the take-up reel during printing saves approximately 1 m (3 ft) of substrate. TIP: If you have already loaded the take-up reel, but the printer fails to recognize that it is loaded, you can save some time by selecting Load it during printing. The following steps assume that you have decided to load immediately. If you decide to load later, during printing, you must complete the same operations without guidance from the front .

ENWW


The take-up reel

35

3.

For easier access to the take-up reel spindle, lift the loading table into its upright position.

4.

Unlock the take-up reel spindle by pushing the spindle lever to its uppermost position.

5.

Remove the take-up reel spindle.


NOTE: The take-up reel spindle is longer than the input spindle: the two are not interchangeable.

36



ENWW

Lift the lever in each case to remove both of the stops from the spindle; they will not be used.

7.

Load the core onto the take-up reel spindle. The core should be at least as wide as the substrate.

8.

Load the take-up reel spindle into the printer by pushing firmly on both ends of the spindle.


6.

ENWW


The take-up reel

37

9.

Press the OK button on the front . Advance the substrate using the arrows on the front . Make sure that the substrate es in front of the loading table, as shown.

10. Pull down the center of the substrate's leading edge to straighten the substrate. Do not attempt to pull more substrate out of the printer. NOTE: If you are loading the take-up reel during printing you do not need to pull the substrate taut. Tape the substrate to the spindle core when an adequate length of substrate has fed from the printer after printing begins. 11. Adjust the position of the core on the take-up reel spindle so that it is aligned with the substrate. 12. Tape the leading edge of the substrate to the core in the center, then at each side. Make sure that the substrate is straight.


13. Press the OK button on the front . The printer advances the substrate.

38



ENWW

14. Press the blue arrow on the take-up reel motor to rotate the spindle one full turn. This will help to the weight of the loop-shaper.

15. Gently lower the loading table, to avoid wrinkles and improve winding.


16. Carefully insert the heavy loop-shaper. This is essential: the take-up reel will not function correctly without it.

ENWW


The take-up reel

39

17. Fit the loop-shaper into the s at either side.

18. Use the wind-direction switch on the take-up reel motor to select the winding direction. Setting 1 winds the substrate so that the printed image faces in. Setting 2 winds the substrate so that the printed image faces out.

The front shows you the correct setting based on the winding-direction decision you made earlier.


19. Press the OK button on the front . The Take-up reel has been successfully installed message appears. 20. The following image shows how the printer looks when it is operating. As substrate is fed from the printer, it drops down in a loop and then up into the take-up reel spindle.

NOTE: While the take-up reel is operating, make sure that the take-up reel sensors are not blocked. NOTE: The cutter is disabled when the take-up reel is in use.

40



ENWW

Load a roll onto the take-up reel (other substrates) 1.


2.

The front offers you the choice of loading the take-up reel immediately, or during printing.

icon, then select Take-up reel > Enable take-up

If you decide to load the take-up reel during printing, familiarize yourself with the procedural steps. Loading the take-up reel during printing requires you to complete the procedure while the printer is feeding and printing substrate. Loading the take-up reel during printing saves approximately 1 m (3 ft) of substrate.

3.

Make sure that the loading table is in its upright position.

4.


ENWW


The take-up reel


The following steps assume that you have decided to load immediately. If you decide to load later, during printing, you must complete the same operations without guidance from the front .

41

5.

Remove the right-hand end of the take-up reel spindle, then the left.

NOTE: The take-up reel spindle is longer than the input spindle: the two are not interchangeable. 6.

Lift the lever to remove one of the stops from the spindle.

7.

Load the core onto the take-up reel spindle. The width of the core should be the same as the width of the substrate, so that the stops at each end can be correctly placed up against the substrate.




ENWW

8.

Ensure that both stops are placed on the spindle, but leave some space between the core and the stops at each end.

9.

Load the take-up reel spindle into the printer by pushing firmly on both ends of the spindle.

10. Press the OK button on the front .


Advance the substrate using the arrows on the front . Make sure that the substrate es in front of the loading table, as shown.

11. Pull down the center of the substrate's leading edge to straighten the substrate. Do not attempt to pull more substrate out of the printer. NOTE: If you are loading the take-up reel during printing you do not need to pull the substrate taut. Tape the substrate to the spindle core when an adequate length of substrate has fed from the printer after printing begins. 12. Adjust the position of the core on the take-up reel spindle so that it is aligned with the substrate.

ENWW


The take-up reel

43

13. Tape the leading edge of the substrate to the core in the center, then at each side. Make sure that the substrate is straight.

14. Press the OK button on the front . The printer advances the substrate.

15. Press the blue arrow on the take-up reel motor to rotate the spindle one full turn. This will help to the weight of the loop-shaper.




ENWW

16. Gently lower the loading table, to avoid wrinkles and improve winding.

17. Assemble a light loop-shaper by matching the shape-coded and color-coded lengths of plastic tubing. The loop-shaper must be the same width as the substrate that you are using. Make sure that both end caps are firmly fitted on the ends of the loop-shaper.


NOTE: The front- display shows the required length of the loop-shaper based on the width of the roll that you have loaded into the printer.

18. Carefully insert the light loop-shaper. This is essential: the take-up reel will not function correctly without it. The loop-shaper must have end caps. Make sure that the end caps extend over the edges of the substrate.

19. Move the stops towards the center until they are pres against the core on both sides, then lock them.

ENWW


The take-up reel

45

20. Use the wind-direction switch on the take-up reel motor to select the winding direction. Setting 1 winds the substrate so that the printed image faces in. Setting 2 winds the substrate so that the printed image faces out.

The front shows you the correct setting based on the winding-direction decision you made earlier.


21. Press the OK button on the front . The Take-up reel has been successfully installed message appears. 22. The following image shows how the printer looks when it is operating. As substrate is fed from the printer, it drops down in a loop and then up into the take-up reel spindle.

NOTE: While the take-up reel is operating, make sure that the take-up reel sensors are not blocked. NOTE: The cutter is disabled when the take-up reel is in use.

46



ENWW

Unload a roll from the take-up reel 1.


icon, then select Take-up reel > Disable take-up

The printer advances the substrate to allow for cutting. Switch the wind-direction switch to the off position. The switch is in the off position when it is centered (in other words, when the switch is neither in position 1 nor position 2).

3.

Remove the loop-shaper. If you omit this step, it will fall to the floor with the substrate when the substrate is cut.


2.

To remove the heavy loop-shaper, first lift the , then press the lever.

ENWW


The take-up reel

47


4.

Use the winding button on the take-up reel motor to wind the excess substrate around the take-up reel spindle.

5.

Press the OK button on the front . The printer asks you to cut the substrate manually.

6.

Use the winding button on the take-up reel motor to wind the remainder of the substrate around the take-up reel spindle.

7.

Press the OK button on the front . The amount of printed substrate that is on the take-up reel spindle appears on the front .

8.

48




ENWW

9.

Remove the roll from the printer, pulling out the end on the right side of the printer first. Do not insert your fingers into the spindle s during the removal process.

10. To remove the roll from the printer after you have unloaded the take-up reel, see Unload a roll from the printer on page 33.

The edge holders The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress. They are recommended for textile and double-sided printing (even if the front does not suggest them), and are not normally necessary in other situations. When not in use, they can be stored in their case at the rear of the printer.

WARNING! Do not touch the printer's drying enclosure. Even after you have opened the window latch, which disconnects the power to the drying and curing modules, the internal surfaces could be hot. The edge holders should be placed on the platen so that they slightly overlap the left and right edges of the substrate. The edge holders fit into holes in the platen, and they are magnetic, which helps them to stay in place.

Slide the edge holder to the left or right with your fingers so that you can see the edge of the substrate in the two square holes in the side of the edge holder.

ENWW


The edge holders

49


If you choose to use them, you should place them on the platen when prompted by the front (this prompt appears when using the loading accessory). Open the window, place the edge holders, then close the window.

The following picture shows an edge holder correctly placed.

NOTE: When you use the edge holders, your prints should have a minimum margin of 10 mm.

The loading accessory Handle the substrate

The loading accessory is designed to help in loading banner/textile/mesh substrates. It is recommended when loading such substrates, but not obligatory. NOTE: The edge holders can be used whether or not you decide not to use the loading accessory. 1.

Select Load with accessory from the Substrate Load menu on the front .

NOTE: If you select Load with accessory, a message is displayed asking whether you want to use the edge holders.

50



ENWW

Lay the textile loading accessory on the loading table and flip forward enough of the white flaps to cover the width of the substrate.

3.

Pull some of the textile substrate from the roll and put the leading edge on the loading accessory.

4.

Flip the white flaps back to cover the leading edge of the substrate. The black patches are magnetic and grip the substrate.


2.

ENWW


The loading accessory

51


5.

Lift the loading accessory and the leading edge of the substrate together.

6.

Load the substrate manually, see Load a roll into the printer (manually) on page 30.

7.

The loading accessory es through the printer's substrate path with the substrate.

8.

The front asks whether you want to use the edge holders. See The edge holders on page 49.



ENWW

9.


NOTE: You should select the name of the particular substrate that you are using in your RIP software, not in the front . TIP: When loading very thin substrates, always select the substrate type as Banner to minimize the vacuum pressure applied while loading; when loading very thick substrates, always select the substrate type as HP Photorealistic to maximize the vacuum pressure. After loading and before printing, go to the front and change to the correct type for the substrate you are loading: icon, then select View loaded substrate > Change loaded substrate. select the

11. The printer checks the substrate in various ways and may ask you to correct problems with skew or tension. NOTE: You can specify the maximum permitted amount of skew at the front : select the icon, then select Substrate handling options > Max skew setting. 12. If you are loading transparent substrate without opaque borders, you are asked to enter the width of the substrate and the distance of the right edge from the printer's side plate (as indicated by the ruler on the front of the curing module). 13. If you have chosen double-sided printing, the front may ask a question about it at this point. 14. The printer calibrates the substrate advance.

ENWW


The loading accessory

53


10. After ing through the printer, the loading accessory can be removed by hand.

15. The front recommends using the Take-Up Reel (TUR). You can choose to load the TUR now, or later during printing; or you can choose not to use it at all. See The take-up reel on page 34.

16. Complete the loading process as usual and adjust the skew if necessary.

Double-sided printing The printer can be used to print on both sides of the substrate, in the following way. NOTE: The print should be at least 28 cm (11 in) wide, otherwise the printer will not be able to find the reference line when printing the second side. Outline


1.

Tell the printer that you intend to print on both sides.

2.

The printer prints the content that you want to appear on the first side. After each job, the printer prints a black reference line that is used to align the matching job on the second side.

3.

Cut and unload the substrate.

4.

Reload the cut substrate upside down and starting at the end. The reference line marking the end of the first side should be face down and near the leading edge.

5.

The printer finds the reference line, and uses it to start printing the second side in the right place.

Double-sided printing can be selected in your RIP software or at the printer's front . The RIP setting takes precedence: if double-sided printing is explicitly turned on or off in the RIP software, the front setting is ignored. NOTE: If you try to move the substrate while printing on either side, the front asks for confirmation, because any such movement prevents correct alignment between the two sides. Double-sided printing in detail 1.

Load the substrate in the normal way for the substrate you are using.

2.

On the printer's front , select the icon, then select Double-sided printing > Side A. Check that the front shows the printer status as Ready for side A. Alternatively, select double-sided printing in your RIP software. NOTE: The automatic cutter and the extra bottom margin are both disabled during double-sided printing.

3.

54

Send one or more jobs to be printed on the first side. Before printing the first job, the printer may advance the substrate by about 0.5 m (20 in) so that the second side can be completely cured.



ENWW

After each job, the printer prints a black reference line that is used to align the matching job on the second side. NOTE: The chance of visible misalignment between the two sides increases with the length of the job. For this reason, in double-sided printing you are recommended not to print any single job that is longer than 3 m (10 ft). 4.

5.

After printing, advance the substrate a little using the Move substrate key. ●

If you plan to attach the substrate to the take-up reel before printing the second side, advance the substrate enough to achieve this.

●

If you plan to attach the substrate to the take-up reel while printing the second side, advance the substrate about 10 cm (4 in).

Cut the substrate, either manually or by going to the front and selecting the icon, then Form feed and cut. Before cutting, ensure that the total length of the cut substrate is more than 2 m (6 ft 7 in), otherwise you may be unable to load it successfully. NOTE: The Form feed and cut command will not work if the substrate cannot be cut by the cutter.

6.

Select the

7.

Reload the substrate with the first (printed) side facing up as it enters the printer, and with the reference line near the leading edge. Reload if necessary until the printer finds less than 1 mm/m skew.

icon, then select Substrate unload.

TIP: You are recommended to use the edge holders when printing the second side, which means using the manual loading procedure. TIP: If you have deliberately not attached the substrate to a spindle, and the front reports that the substrate may be detached from the core, or that the feeding direction is not detected, you can ignore the message and continue. 8.

The front asks, Would you like to load substrate for printing as side B? Select Yes.

9.

The printer searches for the reference line on the substrate. If it fails to find it, the front asks you to move the substrate using the Up and Down keys until the reference line is aligned with the permanent line on the platen. You may find it useful to mark where the reference line is on the other side of the substrate.

ENWW


Double-sided printing

55


TIP: Although it is not strictly necessary, you may find it quicker to use the manual loading procedure as an initial approximation, and then allow the printer to find the reference line more accurately. See Load a roll into the printer (manually) on page 30. If you use only the automatic loading procedure, the printer may take some time to find the reference line.

NOTE: If you know that the automatic search for the reference line is not working (perhaps icon, then select because the substrate-advance sensor is dirty), you can turn it off: select the Substrate handling options > Auto line detection > Off. 10. Send one or more jobs to be printed on the second side. If you send more than one job, they should be sent in reverse order, because printing starts at the end of the second side and works back towards the beginning. NOTE: The jobs printed on the second side should probably be rotated 180 degrees, and may need to be slightly reduced in size to compensate for the contraction of the substrate after ing once through the printer. See also the Maintenance and troubleshooting guide.

View information about the substrate On the printer's front , select the substrate details.

icon, then select View loaded substrate > View


The following information appears on the front : ●

The roll status

●

The substrate family that you have selected

●

The width of the substrate in millimeters (estimated by the printer)

If no substrate is loaded, the message Out of substrate appears. The same information appears on the Embedded Web Server's Supplies page.

56



ENWW

Substrate length tracking The substrate length tracking feature enables you to keep track of how much substrate you have used and how much is remaining on the roll. When the roll is first loaded onto the printer you have the option to enter the length of substrate on the roll. The amount of substrate that is subsequently used is then tracked.

2.

When the substrate is being unloaded, the front will display the amount remaining so that you can note it for future reference.

3.

Next time the substrate is loaded, you can enter the remaining length, and the printer will again track the substrate as it is used. If the substrate was never actually unloaded, for example if there was a substrate jam and the substrate was unloaded and the printer was turned off and on, if you select Last known length the printer will apply the values from when the jam occurred (if the tracking feature was enabled).


1.

The remaining length of substrate is always displayed in the Substrate area of the front . This information may also be displayed in your RIP.

ENWW


Substrate length tracking

57

Enable/disable the length tracking feature 1.

The length tracking feature can be disabled or enabled from the front . Select the then Substrate handling options > Substrate length tracking.

2.

Select On or Off.

icon,

Store the substrate The following are tips for storing substrate: ●

Always keep unused rolls wrapped in the plastic wrap to prevent discoloration and dust accumulation. Rewrap partially used rolls if they are not being used.

●

Do not stack rolls.

●

Allow all substrates to adapt to room conditions out of the packaging for 24 hours before printing.

●

Handle film and glossy substrates by the edges or wear cotton gloves. Skin oils can be transferred to the substrate, leaving fingerprint marks.

●

Keep the substrate tightly wound on the roll throughout the loading and unloading procedures. If the roll starts to unwind, it can become difficult to handle.




ENWW

5

Substrate settings

media presets Each ed substrate has its own characteristics. The printer changes the way it prints on each different substrate. The RIP requires a description of the requirements of each substrate. This description is called the “media preset”. The media preset contains the ICC color profile, which describes the color characteristics of the substrate. It also contains information about other characteristics (RIP and printer settings) and requirements of the substrate that are not directly related to color. Media presets for your printer are installed in the RIP. The RIP contains media presets for only the most commonly used substrates. If you buy a substrate for which your RIP has no preset, you can obtain a preset for a new substrate in the following ways: ●

Try to the media preset from the substrate manufacturer's Web site.

●

If it is not there, try to it from the RIP company's Web site.

●

If it is not there, check availability using the HP Media Finder search application located at http://www.hp.com/go/latexmediafinder/

●

If you cannot find it anywhere, create a new media preset in the RIP. See Add a new substrate on page 59.

●

Further information can be found at http://www.hp.com/go/L26500/solutions/.

Add a new substrate

Substrate settings

This section is provided in case you decide to make your own media preset. Normally there is no need to do this if you can find ready-made presets for all the substrates that you use.

ENWW


media presets

59

Summary

Substrate settings

Select printer settings and color profile The correct printer settings for your substrate may be available from your RIP vendor or substrate vendor. If not, you can start by copying printer settings from a similar substrate of the same family. See ed substrate families on page 20. If you cannot find a similar substrate for some reason, here are some recommended default settings for each substrate family.

60

Chapter 5 Substrate settings


ENWW

Substrate family

Drying temp.

Curing temp.

Heating airflow

Autotracking (OMAS)

Cutter

Substrat eadvance compens ation

Input tension

Vacuum

Self-adhesive

55

110

30

Yes

Yes

0

15

25

Banner

50

110

45

Yes

No

0

15

5

Textile

55

100

45

Yes

No

0

15

20

Film

55

95

30

Yes

Yes

0

15

25

Synthetic paper

50

80

30

Yes

Yes

0

15

40

Paper-aqueous

45

70

30

Yes

Yes

0

15

20

Paper-solvent

50

90

30

Yes

Yes

0

15

25

Low-temperature substrate

50

80

30

Yes

Yes

0

15

40

Mesh

50

95

30

Yes

Yes

0

15

30

The various settings mentioned above are described below. Setting

Description

If too low

If too high

es

The number of es specifies how many times the printheads will print over the same area of the substrate.

The amount of ink fired per time unit is larger and ink has less time to dry on the substrate. This may create coalescence and banding. The boundaries between es may be more visible. However, printing speed is relatively high.

Colors are vivid, print quality is high. However, printing speed is relatively low. A lower curing temperature is needed, otherwise the substrate may be deformed.

The heat applied in the printing zone removes water and fixes the image to the substrate.

Print-quality defects such as banding, bleeding and coalescence may occur.

Thermal marks may be seen on the substrate; they may appear as vertical bands in some colors. The substrate may wrinkle on the platen, causing vertical banding, ink smears or substrate jams.

Curing temp.

Curing is needed to coalesce the latex, creating a polymeric film which acts as a protective layer, while at the same time removing the remaining co-solvents from the print. Curing is vital to ensure the durability of the printed images.

The print may emerge not fully polymerized, so that the ink smears when rubbed. The print may appear wet, after printing or later. You may need to increase the number of es to achieve adequate curing.

Heating airflow

Airflow helps to remove the evaporated water from the print zone and thus allows more efficient drying.

In general, use the substrate family default value.

ENWW


The substrate may wrinkle under the curing module, causing defects such as blisters or liner detachment. The substrate wrinkles may also cause vertical banding or ink smears at the beginning of the following plot.

Add a new substrate

Substrate settings

Drying temp.

61

Setting

Description

If too low

If too high

Substrate advance compensation

Your printer was calibrated at the factory to ensure that it advances the substrate accurately when using ed substrates in normal environmental conditions. However, you may find it useful to adjust the substrate advance when printing in an unusual but stable temperature or humidity level, or if the substrate-advance sensor is not working.

You may see horizontal banding or grain.

You may see horizontal banding or grain.

Input tension

Tension is applied to the substrate from the input spindle. It needs to be constant over the full width of the substrate, thus substrate load is a critical operation.

The substrate skews and may become increasingly wrinkled in the printing zone. Also, substrate advance may be irregular, resulting in horizontal banding.

The substrate may be permanently deformed or damaged. Substrate advance problems may appear in extreme cases.

Vacuum

The vacuum applied to the substrate at the printing zone helps to hold the substrate down on the print platen, keeping the distance to the printheads constant.

The substrate may lift up off the platen and touch the printheads. This can smear the printed image, cause vertical banding, cause a substrate jam or even damage the printheads.

For sticky substrates, friction could be too high and substrate advance irregular, resulting in horizontal banding or irregular grainy patches.

Bidirectional

Specifies whether printheads print in both directions, when moving from left to right and from right to left.

If Bidirectional is selected, the amount of ink fired per unit of time is larger, and therefore print quality defects such as coalescence and banding may occur, especially at the sides of the plot. However, printing speed is high.

If Bidirectional is unchecked then the printing is unidirectional and the speed is relatively low.

The maximum quantity of ink will be laid on the substrate (the High ink level option available only when the number of es is 10 or more). The ink quantity may be reduced by the RIP color profile.

If not selected, colors may look washed-out.

If selected, there can be excess of ink and some problems related to poor drying and curing.

High ink level

TIP: You are recommended to keep Bidirectional selected in all cases, increasing the number of es if necessary to avoid coalescence and banding.

TIP: Select High ink level for backlit and some textile applications, or if you want high color saturation.

Substrate settings 62



ENWW

Setting

Description

If too low

If too high

Cutter

The printer's built-in cutter can cut the substrate automatically between each print.

Disable the cutter in the following cases: ●

You want to increase the speed of printing.

●

You want to use the take-up reel.

●

You want to cut the substrate manually.

●

The leading edge of the substrate tends to curl and cause substrate jams.

In some cases, the cutter is automatically disabled. Auto tracking (OMAS)

The substrate-advance sensor (also known as the Optical Media Advance Sensor, OMAS) is located under the print platen; it can track the substrate advance automatically.

Disable the sensor in the following cases: ●

The substrate allows ink to through to the platen. Clean the sensor after using this substrate.

●

You are instructed to do so by the front , because the sensor is dirty or unable to track this particular substrate.

Load the substrate and print the diagnostic plot 1.

Load the substrate in the normal way, paying particular attention to the following points. ●

The stop at the right-hand end of the spindle has two possible positions on the spindle. Always use the leftmost position if possible. Use the rightmost position only if the substrate roll requires the full width of the spindle.

●

Turn off the substrate-advance sensor (OMAS) in the RIP if the substrate is transparent or dark, or if the printer recommends you to do so.

●

Align the printheads.

Open the HP diagnostic chart in the RIP. The chart is stored in your printer, at http://ip-addr/ hp/device/webAccess/images/new.tif, where ip-addr is the IP address of your printer. You can also find it at http://www.hp.com/go/L26500/manuals/.

3.

Select a suitable number of es for the substrate family. See Select the number of es on page 66.

4.

Print the plot.

Substrate settings

2.

ENWW


Add a new substrate

63

Change settings while printing You can use the front to change the following settings while printing. ●

To change temperature and vacuum settings while printing: select the icon, then Image quality maintenance > Adjust printing params, and choose the setting that you want to adjust. You can use the arrow keys to adjust the curing temperature, the drying temperature or the vacuum pressure. The changes that you make take effect immediately, but they are not saved: the next job will use the settings in the media profile as usual.

●

To change substrate advance calibration while printing (in case of banding): select the icon, then Image quality maintenance > Substrate advance calib > Adjust substrate advance. You can use the arrow keys to adjust the substrate advance. The changes that you make take effect immediately, but they are not saved for the next job. See also the Maintenance and troubleshooting guide.

●

To enable or disable extra printhead cleaning while printing: select the icon, then Image quality maintenance > Enable extra PH cleaning or Disable extra PH cleaning. In this case, the change of setting is saved for subsequent jobs. NOTE: Extra printhead cleaning shortens the life of the printhead cleaning cartridge.

Advanced settings Here are some more advanced settings, which you are not recommended to change, unless you have problems that you cannot resolve any other way. The drying and curing temperatures used by the printer are determined by adding the offset to the base temperature. The base temperatures shown in the table are the default values for each substrate family, but may be changed by the printer depending on the printer settings in use. You cannot change the base temperatures yourself, but you can change the offsets. The base warm-up drying temperature is determined by the RIP. Your RIP may have an option to return all settings to their default values. Substrate family

Substrate settings

Warm-up drying temperat ure offset

Warm-up curing temperat ure

Warm-up curing temperat ure offset

Cooldown drying temperat ure

Cooldown drying temperat ure offset

Cooldown curing temperat ure

Cooldown curing temperat ure offset

Minimum drying power

Selfadhesive

10

95

0

80

0

95

0

0.7

Banner

10

95

0

80

0

90

0

0.7

Textile

5

85

0

80

0

90

0

0.7

Film

5

85

0

80

0

100

0

0.7

Synthetic paper

5

80

0

75

0

85

0

0

Paperaqueous

5

60

0

75

0

85

0

0

10

75

0

75

0

90

0

0.7

Papersolvent

64



ENWW

Substrate family

Warm-up drying temperat ure offset

Warm-up curing temperat ure

Warm-up curing temperat ure offset

Cooldown drying temperat ure

Cooldown drying temperat ure offset

Cooldown curing temperat ure

Cooldown curing temperat ure offset


Low-temp.

10

80

0

75

0

85

0

0

Mesh

10

85

0

80

0

85

0

0.7

The various settings mentioned above are described below. Setting

Description

If too low

Warm-up drying temperature

The base temperature that the substrate in the print zone must reach before printing starts.

This setting is determined by the RIP. You cannot change it.

Warm-up drying temperature offset

This offset is added to the base warm-up drying temperature, and the total is displayed in the front while the printer is preparing to print.

Bleeding or coalescence may appear in the first 200-300 mm of the print.

Warm-up curing temperature

The base temperature that the substrate in the curing zone must reach before printing starts.

This setting is determined by the printer. You cannot change it.

Warm-up curing temperature offset

This offset is added to the base warm-up curing temperature, and the total is displayed in the front while the printer is preparing to print.

The beginning of the print is not fully dry, or looks oily.

Cool-down drying temperature

The base temperature at which the substrate can be under the drying module without being damaged. At the end of a job, the substrate is not stopped until this temperature is reached.


Cool-down drying temperature offset

This offset is added to the base cool-down drying temperature.

A long time is needed to finish the print.

Cool-down curing temperature

The base temperature at which the substrate can be under the curing module without being damaged. At the end of a job, the substrate is not stopped until this temperature is reached.


Cool-down curing temperature offset

This offset is added to the base cool-down curing temperature.

A long time is needed to finish the print.

The end of the print may be damaged if the cutter is disabled.


The minimum power applied in the drying module while printing, so the substrate does not cool too much in lightly inked areas.

A heavily inked area that comes after a lightly inked area will have bleeding or coalescence defects.

The substrate is damaged in blank or lightly inked areas of the print, especially with a high number of es.

ENWW


If too high

A longer time to start printing is required. Vertical banding or ink smears may occur.

Substrate degradation (blisters, adhesive detachment) at the beginning of the print.

Add a new substrate

Substrate settings

The substrate at the beginning of the next print may be damaged, because it has stopped moving under too high a temperature. This case is uncommon.

65

Temperature profile Many of the main and advanced substrate settings are related to temperature control, since this is a critical area for correct printing results with latex inks on a wide variety of substrates. The diagram below graphically represents the evolution of drying and curing temperatures during the various printing phases.

NOTE: Target temperatures and time are not to scale. For the specific values used for a given substrate type (family), consult the main and advanced settings tables above. NOTE: tp time can be modified through the printer’s front .

Select the number of es Increasing the number of es will tend to improve the print quality but reduce the speed of printing.


es

Uni/ bidir

Self adhesi ve

Banner

Textile

Film

Synthet ic paper

Paper aqueou s

Paper solvent

Low temp.

Mesh

4

Bidir

No

No

No

No

No

No

No

No

No

6

Bidir

Maybe

Start here

No

No

No

Start here

Maybe

Maybe

No

8

Bidir

Start here

Yes

No

No

No

Yes

Start here

Start here

Start here

10

Bidir

Yes

Yes

No

No

No

Yes

Yes

Yes

Yes

12

Bidir

Yes

Yes

Start here

Maybe

Maybe

Yes

Yes

Yes

Yes

16

Bidir

Yes

Yes

Yes

Start here

Start here

Yes

Yes

Yes

Yes



ENWW

es

Uni/ bidir

Self adhesi ve

Banner

Textile

Film

Synthet ic paper

Paper aqueou s

Paper solvent

Low temp.

Mesh

18*

Bidir

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

20 to 32

Bidir

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

* Unlike other printmodes, the 18- printmode has 1200 dpi x 1200 dpi input data resolution at 1 bpp (1 bit per pixel). Therefore, to generate a 18- media preset you should start either from an existing 18- preset or from scratch. In the same way, do not clone an 18- media preset to generate a preset with a print mode other than 18-. Key ●

Bidir: bidirectional

●

No: not recommended

●

Maybe: may be worth trying for extra speed

●

Start here, Yes: recommended

NOTE: More specific settings for many substrates from different vendors are available in the HP Media Finder at http://www.hp.com/go/latexmediafinder/.

Check the quantity of ink on the substrate Check that the ink quantities in your media preset are adequate. Look at the color patches in the HP diagnostic chart and check that the patches have the correct amount of ink using the guidelines below: 1.

Too much ink: There are several possible symptoms of this problem. The last two or three scales of the chart look the same.

Substrate settings

●

ENWW


Add a new substrate

67

●

Vertical bands.

●

Horizontal bands.

●

Coalescence, grain (can be caused by an excess of light ink).

Try reducing the amount of ink in your RIP software, then reprint the chart and check again.

Substrate settings

You may have chosen a media preset that uses more ink than your substrate allows. Consult your RIP documentation to make sure you’re applying the right media preset, and to find out how to lower the total ink limits of the media preset. For a quick solution, you could change to a different media preset that uses less ink: for example, paper-aqueous presets use less ink than self-adhesive presets.

68



ENWW

2.

Correct amount of ink: The top level of each patch shows a smooth gradient, there are no visible defects and increasing amounts of ink result in increasing color density.

3.

Too little ink: The whole chart looks washed out.

Try increasing the amount of ink in your RIP software, then reprint the chart and check again. You may have chosen a media preset that uses less ink than your substrate allows. Consult your RIP documentation to make sure you’re applying the right media preset, and to find out how to increase the total ink limits of the media preset. For a quick solution, you could change to a different media preset that uses more ink: for example, self-adhesive presets use more ink than paper-aqueous presets.

Substrate settings

NOTE: Backlit and some textile substrates usually need to be used with the “High Ink Limit” option enabled in the RIP.

ENWW


Add a new substrate

69

Faster printing The obvious way to increase speed is to reduce the number of print es, although this will tend to reduce print quality. Bear in mind the following considerations. ●

With fewer than 10 es, you may see an increase in grain.

●

With fewer than 8 es, the printer is more sensitive to substrate advance problems.

●

With fewer than 8 es, you may need to reduce the ink quantity to improve print quality.

●

If you want to use the high ink level option, you must use at least 10 es.

●

As you reduce the number of es, the best curing temperature may be more difficult to find, and may be more sensitive to the ambient temperature and humidity.

Here are some other suggestions for increasing the speed of printing. ●

Concatenating prints saves time, because one can be sent while another is being printed.

●

Disable the cutter: select the icon, then select Substrate handling options > Enable cutter > Off. With most substrates, this saves some time at the end of the printing process.

●

Increase the cool-down curing temperatures. This also saves some time at the end of the printing process, but may cause slight substrate deformation, depending on the substrate.

See also the Maintenance and troubleshooting guide.

Color calibration The purpose of color calibration is to produce consistent colors with the specific printheads, inks and substrate that you are using, and in your particular environmental conditions. After color calibration, you can expect to get identical prints from your printer on different occasions. Color calibration can be launched from your RIP software; see your RIP documentation for details. In outline, the process consists of the following steps. 1.

A calibration test chart is printed.

2.

The HP Embedded Spectrophotometer (or, if you prefer, a different spectrophotometer) scans and measures the test chart.

3.

The RIP uses the measurements to calculate the necessary correction factors for consistent color printing on that substrate.

Substrate settings

Color calibration with the Embedded Spectrophotometer is not recommended for the following substrate types. It may be possible to calibrate some of these substrates by using an external color measurement device.

70

●

Non-opaque substrates such as clear film, backlit substrates, and some textiles.

●

Substrates with an uneven surface, such as perforated vinyl or punched-window substrates.

●

Substrates that suffer deformation from drying and curing, such as paper-based substrates.

●

Very elastic substrates, such as some textiles without liner.



ENWW

Substrates suitable for color calibration include even-surfaced adhesive vinyls (neither punched nor perforated), PVC banners and some opaque, stiff textiles. Some textiles require the take-up reel for successful printing. However, the take-up reel may fail to cope with the backward movement of the substrate between the printing and scanning phases of color calibration. To avoid this problem, proceed as follows. 1.

Ensure that the take-up reel is enabled.

2.

Advance the substrate until the loop-shaper reaches its lowest position.

3.

Manually rewind the take-up reel, using the buttons on the take-up reel motor, to collect the substrate and raise the loop-shaper until it almost touches the take-up reel spindle.

4.

Set the take-up reel's wind direction to neutral.

5.

Launch color calibration from the RIP.

6.

When the color calibration has finished, you can re-enable the take-up reel.

Color profiles Color calibration provides consistent colors, but consistent colors are not necessarily accurate. For instance, if your printer prints all colors as black, its colors may be consistent but they are not accurate. In order to print accurate colors, it is necessary to convert the color values in your files to the color values that will produce the correct colors from your printer, your inks and your substrate. A color profile is a description of a printer, ink and substrate combination that contains all the information needed for these color conversions. These color conversions are performed by your Raster Image Processor (RIP), not by the printer. For further information on the use of color profiles, see the documentation for your application software and for your RIP. In addition to the color profiles used for printing, you may wish to calibrate and profile your monitor (display device), so that the colors you see on the screen relate more closely to those that you see on your prints.

Color reproduction tricks

●

To achieve the best dark colors in vinyl gloss and other substrates, use as much black and as little composite (CMY) as possible when creating the ICC profile.

●

Light inks should be avoided as much as possible in high-density colors such as secondaries and tertiaries (dark red, blue, green, ...).

●

Light inks should be restricted to the lowest-density colors, starting the use of dark inks as early as possible. Typically, a color of more than 50% density should not contain any light inks.

●

Light inks should be used at no more than 50% of maximum quantity. An excessive amount of light inks can create gloss artifacts in vinyl gloss substrates.

Please refer to your RIP documentation for details of how to create or modify media presets.

ENWW


Color profiles

71

Substrate settings

Latex inks are a new technology, and there are some important guidelines when doing color separations (such as when creating or modifying a new media preset within your RIP) that will help to optimize the printer output in of color gamut, ink usage and print quality. These are as follows:

Presets for HP-branded substrates have been created following the above recommendations in order to optimize black and dark colors. You can find the HP media preset for your substrate family at http://www.hp.com/go/latexmediafinder/.




ENWW

Usage information

6

Retrieving usage information

●

Get ing information

●

Check usage statistics

●

Check usage statistics for a job

●

Request ing data by E-mail

ENWW


73

Usage information

Get ing information There are various different ways of getting ing information from your product. ●

View product usage statistics for the whole lifetime of the product, see Check usage statistics on page 74.

●

Request ing data by E-mail. The product sends data in XML at regular intervals to a specified E-mail address; the data may be interpreted and summarized by a third-party application, or displayed as an Excel spreadsheet. See Request ing data by E-mail on page 74.

●

Use a third-party application to request product status, product usage or job ing data from the product through the Internet. The product provides data in XML to the application whenever requested. HP provides a Software Development Kit to facilitate the development of such applications.

Check usage statistics There are two ways of checking your product's usage statistics. NOTE: The accuracy of the usage statistics is not guaranteed. ●

From the Embedded Web Server, go to the Main tab and select History > Usage.

●

From the front , select the Print usage report.

icon, then Internal prints > information prints >

Check usage statistics for a job You can use the Embedded Web Server to check usage statistics for a particular job: go to the Main tab and select History > ing. NOTE: The accuracy of the usage statistics is not guaranteed.


74

1.

Obtain the IP address of the outgoing mail server (SMTP) from your IT department; this is required in order to send e-mail messages.

2.

Ensure that the outgoing e-mail server is configured to enable relaying of e-mail messages that the product will send.

3.

Open your Web browser and connect to the product’s Embedded Web Server.

4.

Select the Setup tab.

5.

From the Configuration menu in the left-hand column, select Date & Time.

6.

Ensure that the product's date and time have been set correctly.

7.

From the Configuration menu, select E-mail server..

8.

Enter the IP address of the outgoing mail server (SMTP).

Chapter 6 Retrieving usage information


ENWW

Usage information

9.

Specify an e-mail address for the product. The latter does not need to be a valid e-mail address, because the product will not receive messages; but it should have the form of an e-mail address. It serves to identify the product when it sends e-mail messages.

10. From the Configuration menu, select Printer settings. 11. In the ing section, if you set Require ID to On, then every time someone sends a print job to the product, he or she must provide an ID: for example, an ID corresponding to his or her department or to a specific project or client. If someone sends a job without providing an ID, the product will hold the unidentified job in the queue without printing it until an ID is provided. If you set Require ID to Off, then the product will print all jobs whether or not they have an ID. 12. Set Send ing files to Enabled. 13. Set Send ing files to to the e-mail address (or addresses) to which you want the ing information sent. This may be an address that you have created specifically to receive automatically generated messages from the product. 14. Set Send ing files every to the frequency with which you want the information sent, choosing a specific number of days or prints. 15. You may want to set Exclude personal information from ing e-mail to On, so that the ing messages will not contain personal information. If this option is Off, information such as name, job name, and ID will be included. When you have completed the above steps, the product will send ing data by E-mail with the frequency that you specified. The data are provided in XML and can easily be interpreted by a thirdparty program. The data provided on each print job include when the job was submitted, when the job was printed, the printing time, the type of image, the number of pages, the number of copies, the paper type and size, the amount of each color of ink used and various other attributes of the job. ing data are also provided on scan and copy jobs. You can an Excel template from HP's Web site (http://www.hp.com/go/designjet/ ing/) that will enable you to display the XML data more readably in the form of a spreadsheet. Analysis of the ing data will enable you to bill customers precisely and flexibly for the use of your product. You can, for instance: ●

Bill each customer for the total amount of ink and paper used by that customer over a particular period.

●

Bill each customer separately per job.

●

Bill each customer separately for each project, broken down by job.

ENWW



75

7

The ink system

The ink system

Ink system components Ink cartridges The printer's six ink cartridges provide magenta, light magenta, black, yellow, light cyan and cyan ink to the printheads. Each cartridge has a capacity of 775 ml.

Ink cartridges require no maintenance or cleaning, but must be shaken before installation. High-quality printing results continue even when the ink levels are getting low. CAUTION: Avoid touching pins, leads, and circuitry when handling ink cartridges because these elements are sensitive to electrostatic discharge. Such devices are called ESD-sensitive devices. See Glossary on page 87. Electrostatic discharges are one of the main hazards to electronics products. This type of damage can reduce the life expectancy of the device.

Printheads The printheads deposit ink on the substrate. Each printhead is connected to two ink cartridges. For example, the printhead shown below draws ink from the light magenta and magenta cartridges.

76

Chapter 7 The ink system


ENWW

The ink system

The printheads are extremely durable and do not need to be replaced every time an ink cartridge is replaced. They provide excellent results even when the ink cartridges contain a low level of ink. To maintain optimum print quality, the printheads are automatically tested at regular intervals, and automatically serviced when necessary. This takes a little time and can occasionally delay printing. When a printhead eventually needs to be replaced, the front will display a message. CAUTION: Avoid touching pins, leads, and circuitry when handling printheads because these elements are sensitive to electrostatic discharge. Such devices are called ESD-sensitive devices. See Glossary on page 87. Electrostatic discharges are one of the main hazards to electronics products. This type of damage can reduce the life expectancy of the device.

Printhead cleaning kit The printhead cleaning kit contains the printhead cleaning cartridge, the ink funnel and the ink filter.

Printhead cleaning cartridge The printhead cleaning cartridge cleans and maintains the printheads, and seals the printheads when they are not in use to prevent them from drying out.

The cartridge contains a roll of cloth, which is used to clean the printheads. You are notified when 92% of the roll has been used, after which the cartridge should continue to function for at least another 140 m² (1500 ft²) of printed area. A new roll lasts for at least 1850 m² (20000 ft²) of printed area. The printer will refuse to start a print job if it detects the end of the cleaning roll. You should then replace the printhead cleaning cartridge with a new one.

ENWW


Ink system components

77

Ink funnel The ink funnel collects waste ink produced during printhead servicing. It is important that this funnel is installed, as it prevents significant deposits of ink over various other printer parts. From the ink funnel, the waste ink es through the ink tube assembly into the printhead cleaning container.

The ink system Ink filter The ink filter filters tiny droplets of waste ink before they into the printhead cleaning container.

Printhead cleaning container The printhead cleaning container stores waste ink collected by the ink funnel.

78



ENWW

The ink maintenance kit ●

The ink funnel, which collects tiny droplets of waste ink produced during printhead servicing.

●

The ink tube assembly, which es tiny droplets of waste ink collected by the ink funnel to the printhead cleaning container

The ink system

The ink maintenance kit contains the following components.

If the printer asks you to replace the ink tube assembly, you should replace the ink funnel and the ink filter at the same time. ●

The ink filter, which filters tiny droplets of waste ink before they into the printhead cleaning container.

These components are designed to keep the printer's waste ink from damaging the printer and dirtying the environment.

ENWW


Ink system components

79

In order to keep the printer and its surroundings clean, you must ensure that these components are correctly installed and maintained. In particular, these steps are essential: 1.

Connect the ink tube assembly.

2.

Insert the ink funnel.

3.

Insert the ink filter and close the filter box.

4.

Install the printhead cleaning container.

The ink system

If the printer continues operating while these components are incorrectly installed or incorrectly connected, HP will not be responsible for any resulting damage or cleaning expenses. The printer displays a message on the front if it detects any problem with these components.

Order ink supplies You can order the following ink supplies for your printer. Table 7-1 Ink cartridges Cartridge

Capacity (ml)

Part number

HP 792 Black Latex Designjet Ink Cartridge

775

CN705A

HP 792 Cyan Latex Designjet Ink Cartridge

775

CN706A

HP 792 Magenta Latex Designjet Ink Cartridge

775

CN707A

HP 792 Yellow Latex Designjet Ink Cartridge

775

CN708A

HP 792 Light Cyan Latex Designjet Ink Cartridge

775

CN709A

HP 792 Light Magenta Latex Designjet Ink Cartridge

775

CN710A

Table 7-2 Printheads Printhead

Part number

HP 792 Yellow and Black Designjet Printhead

CN702A

HP 792 Cyan and Light Cyan Designjet Printhead

CN703A

HP 792 Light Magenta and Magenta Designjet Printhead

CN704A

Table 7-3 Waste management system Kit

80

Part number

HP 792 Designjet Printhead Cleaning Kit

CR278A

HP 792 Designjet Ink Maintenance Kit

CR279A

HP 789/792 Designjet Printhead Cleaning Container

CH622A



ENWW

8

Print options

Printer states The printer may be in any one of the following states; some of them require waiting. Ready (cold): The printer is powered on but has not printed yet, and the heaters are not turned on.

●

Preparing to print: The printer is warming up the heaters and preparing the printheads to print. This takes 1 to 8 min.

●

Ready for substrate

●

Ready for side A/B

●

Printing

●

Printing side A/B

●

Curing: This takes 1.5 to 5 min.

●

Finishing: The printer is cooling down and preparing for stand-by. This takes 0.5 to 5 min.

Print options

●

If jobs of the same print mode as the already-printed file are sent while the printer is Curing (if the cutter is not enabled) or Finishing, the printer goes to Preparing to print. To save time between prints, concatenate jobs with the same print mode (same number of es) and turn the cutter off to skip the Curing and Finishing states. You can also use nesting to print several jobs in the same workflow. Even if the cutter is on or successive jobs use different print modes, it is better to print them all together without delays to minimize the time spent in Preparing to print.

Change margins The printer margins determine the area between the edges of your image and the edges of the substrate. The margins for a particular print job are selected in the RIP software; if the job exceeds the substrate width, it will be clipped. The front offers additional settings for the bottom margin: see Table 10-4 Margins on page 85. These settings apply only to single prints when the cutter is not in use. The bottom margin is not applied between several prints sent at the same time, nor during double-sided printing.

ENWW


Printer states

81

To set the bottom margin at the front , select the Extra bottom margin.

icon, then Substrate handling options >

NOTE: The extra bottom margin set in the front is applied in addition to the bottom margin selected in the RIP.

Request the printer’s internal prints The internal prints provide various kinds of information about your printer. Request these prints from the front , without using a computer. Before requesting any internal print, make sure that substrate is loaded and that the Ready message appears on the front- display. To print an internal print, select the you want.

icon, Internal prints, then select the type of internal print that

The following internal prints are available:

Print options 82

●

Menu map: Shows details of all the front- menus.

●

Configuration: Shows all the current front- settings.

●

Usage report: Shows estimates of the total number of prints, number of prints by substrate family, number of prints by print-quality option, and total amount of ink used per color. The accuracy of these estimates is not guaranteed.

●

Service information: Provides information that service engineers require.

Chapter 8 Print options


ENWW

9

Accessories

Order accessories The following accessories can be ordered for your printer. TIP: Spare spindles ease the process of switching between different substrates.

Name

Product number CR765A

HP Designjet L26500 61 × 2-inch Spindle

CV063A

HP Designjet L26500 61 × 3-inch Spindle

CV135A

HP Designjet L26500 Maintenance Kit

CQ201A

Accessories

HP Designjet Soft Media Loading Accessory

ENWW


Order accessories

83

10 Printer specifications

Functional specifications Table 10-1 HP No. 792 ink supplies Printheads

Yellow/black, cyan/light cyan and light magenta/magenta

Ink cartridges

Yellow, black, magenta, light magenta, cyan and light cyan. All cartridges contain 775 ml of ink.

Printhead cleaning kit

Non-color-specific

Ink tube assembly

Non-color-specific

Ink filter

Non-color-specific

Table 10-2 Substrate sizes

Width

Minimum

Maximum

584 mm (23 in)

1549 mm (61 in)

Narrow substrate: 254 mm (10 in) Length

1.5 m (59 in)

Roll with maximum external diameter of 180 mm (7.1 in)

Table 10-3 Print resolutions

Printer specifications

Ink level

Number of es

Halftone resolutions (dpi)

Print resolutions (dpi)

100%

4–28 (except 18)

300, 600

1200×1200

18

1200

1200×1200

10–28 (except 18)

300, 600

1200×1200

18

1200

1200×1200

200%

The table above shows the resolutions ed by the printer. See your RIP documentation to find the resolutions ed by your RIP.

84

Chapter 10 Printer specifications


ENWW

Table 10-4 Margins Side margins

5 mm (0.2 in)

Top margin (leading edge)

5 mm (0.2 in)

Bottom margin (trailing edge)

5 mm (0.2 in) (none) 100 mm (3.9 in) (small) 150 mm (5.9 in) (normal) 200 mm (7.9 in) (extra) 300 mm (11.8 in) (extra) 400 mm (15.7 in) (extra) 500 mm (19.7 in) (extra)

Physical specifications Table 10-5 Printer physical specifications Weight (including stand)

290.1 kg

Width

2465 mm

Depth

690 mm

Height

1370 mm

Memory specifications Table 10-6 Memory specifications Memory (DRAM)

512 MB

Hard disk

160 GB

NOTE: An electrician is required for the setup and configuration of the building electrical system used to power the printer and also for printer installation. Make sure that your electrician is appropriately certified according to local regulations and supplied with all the information regarding the electrical configuration. Your printer requires that the following electrical components be supplied and installed by the customer, according to the National Electrotechnical Code (NEC). Table 10-7 Single phase line specifications

Number of power cords

ENWW


Outside Japan

Japan only

2

2

Physical specifications

85

Printer specifications

Power specifications

Table 10-7 Single phase line specifications (continued) Outside Japan

Japan only

Input voltage

220-240 V~ (-10%+6%)

200V (-10%+10%)

Input frequency

50 / 60 Hz

50 / 60 Hz

Power consumption

4.8 kW (overall consumption for both power cords)

4.8 kW (overall consumption for both power cords)

Maximum load current (per power cord)

15 A

15 A

Environmental specifications Table 10-8 Printer environmental specifications Relative humidity range for best print quality

20–80%, depending on substrate type

Temperature range for best print quality

18 to 25°C (64 to 77°F), depending on substrate type

Temperature range for printing

15 to 30°C (59 to 86°F)

Temperature range when not in operation

-25 to +55°C (-13 to +131°F)

Temperature gradient

no more than 10°C/h (18°F/h)

Maximum altitude when printing

3000 m (10000 ft)

NOTE: The printer must be kept indoors. NOTE: If the printer or ink cartridges are moved from a cold location to a warm and humid location, water from the atmosphere can condensate on the printer parts and cartridges and can result in ink leaks and printer errors. In this case, HP recommends that you wait at least 3 hours before turning on the printer or installing the ink cartridges, to allow the condensate to evaporate.

Acoustic specifications Table 10-9 Printer acoustic specifications

Printer specifications 86

Idle sound power

≤ 5.1 B (A)

Operating sound power

≤ 7.5 B (A)

Idle sound pressure

≤ 39 dB (A)

Operating sound pressure

≤ 56 dB (A)

Chapter 10 Printer specifications


ENWW

Glossary

Airflow Air is blown through the printing zone to speed up the drying process. Back tension The backwards tension applied to the substrate by the input spindle, which must be constant across the width of the substrate. Too much or too little tension may cause substrate deformation and print quality defects. Bidirectional Bidirectional printing means that the printheads print while moving in both directions. This increases the speed of printing. Bleeding A print-quality defect that occurs when the ink spreads on the substrate across areas of different colors. Coalescence A print-quality defect that occurs when the ink spreads on the substrate within an area of the same color. Cockle A substrate condition in which it is not lying perfectly flat, but rises and falls slightly in shallow waves. Color accuracy The ability to print colors that match the original image as closely as possible, given the fact that all devices have a limited color gamut and might not be able to match certain colors precisely. Color consistency The ability to print the same colors in a particular print job, from print to print and from printer to printer. Curing The substrate is heated in the curing zone to coalesce the latex, creating a polymeric film which acts as a protective layer, while at the same time removing the remaining co-solvents from the print. Curing is vital to ensure the durability of the printed images. Too high or too low a curing temperature may cause print quality defects. Cutter A printer component that slides back and forth across the platen to cut the substrate. Drying The substrate is heated in the printing zone to dry the ink and fix the image to the substrate. Too high or too low a drying temperature may cause print quality defects. Edge holder A metal piece designed to prevent the edge of the substrate from rising while printing is in progress. Firmware Software that controls your printer's functionality and is stored semi-permanently in the printer (it can be updated). Gamut The range of colors and density values reproducible on an output device, such as a printer or monitor. HDPE High Density Polyethylene.

ENWW


Glossary

87

I/O Input/Output: this term describes the ing of data between one device and another. ICC The International Color Consortium, a group of companies that have agreed on a common standard for color profiles. Ink density The relative amount of ink that is deposited on the substrate per unit of area. IP address A unique identifier that identifies a particular node on a T/IP network. It consists of four integers separated by dots. LED Light-Emitting Diode: a semiconductor device that emits light when electrically stimulated. Loading accessory A flexible plastic accessory that fits over the leading edge of the substrate while it is being loaded into the printer. Some substrates are difficult to load without this accessory. Loop-shaper A cylindrical weight inserted into the loop of substrate required by the take-up reel. A light and a heavy loopshaper are provided, to suit different substrate types. Minimum drying power The minimum heat applied in the printing zone so that the substrate does not cool too much in lightly-inked areas. Low minimum power may cause print quality defects; high minimum power may damage the substrate, especially with a high number of es and in blank or lightly-inked areas. Nozzle One of many tiny holes in a printhead through which ink is deposited onto the substrate. OMAS The Optical Media Advance Sensor, otherwise known as the substrate-advance sensor. The sensor located in the print platen that tracks the substrate movement and increases its accuracy. es The number of print es specifies how many times the printheads will print on the same area of substrate. A higher number of es tends to improve print quality and printhead health, but reduces the speed of printing. PC Polycarbonate. PE Polyethylene. PET Polyethylene Terephthalate (polyester). PLA Polylactic Acid. Platen The flat surface within the printer over which the substrate es while it is being printed on. PP Polypropylene. Printhead A removable printer component that takes ink of one or more colors from the corresponding ink cartridge(s) and deposits it on the substrate, through a cluster of nozzles.

88

Glossary


ENWW

PVC Polyvinyl Chloride. Spindle A rod that s a roll of substrate while it is being used for printing. Substrate A thin, flat material designed to be printed on, made of paper or other materials. Substrate advance compensation A slight adjustment to the amount of substrate advance between print es, to compensate for the characteristics of different substrate types. The printer normally performs this adjustment automatically, but may need to be recalibrated for substrates not ed by HP, or for an unusual ambient temperature or humidity. Incorrect substrate advance compensation may cause banding with fewer than 8 es, or graininess with 8 es or more. Substrate-advance sensor The sensor located in the print platen that tracks the substrate movement and increases its accuracy. Otherwise known as OMAS (Optical Media Advance Sensor). Unidirectional Unidirectional printing means that the printheads print only while moving in one direction. The speed of printing is lower than in bidirectional. In general, print bidirectional and increasing the number of es is a better way of improving print quality. Vacuum pressure The substrate is held flat against the platen by vacuum suction. Too much or too little suction may cause print quality defects. Too little suction may also cause a substrate jam or damage the printheads.

ENWW


Glossary

89

Index

A access control 18 accessories order 83 ing 74 ing data by E-mail 74 acoustic specifications 86 add new substrate 59 altitude 15 B buzzer on/off 16 C calibration color 70 caution 3 color calibration 70 color profile tricks 71 color profiles 71 color reproduction tricks 71 components of printer 5 connect the printer 13 connection method 13 contrast in front 16 cool-down delay 16 cutter disable 70 D date and time 15 diagnostic plot 60 double-sided printing 54 ing media presets 59 drying enclosure 8 E e-mail alerts 16 edge holders 49 edge holders case 7 Embedded Web Server access 17 e-mail alerts 16

90

10

Index


language 17 usage per job 74 usage statistics 74 environmental specifications 86

substrate unload 55 unload roll 33 view substrate details 56 functional specifications 84

F faster printing 70 features of printer 5 front 9 language 15 front view 6 front- options adjust printing params 64 adjust substrate advance 64 audio alert 16 auto line detection 56 change loaded substrate 20, 32, 53 cooldown wait when idle 16 date and time options 15 disable take-up reel 47 enable extra PH cleaning 64 enable narrow substrate 27, 30 enable take-up reel 34, 35, 41 extra bottom margin 82 form feed and cut 55 internal prints 82 load roll 27 load with accessory 50 manual load 30 max skew setting 29, 32, 53 print usage report 74 reset EWS 18 restore factory settings 17 select altitude 15 select display contrast 16 select language 15 select units 16 side A 54 sleep mode wait time 16 substrate length tracking 58

H hard disk specification 85 HP diagnostic plot 60 I ink

usage 74 ink cartridge about 76 ordering 80 specification 84 ink filter about 78 ink funnel about 78 ink tube assembly about 79 internal prints 82 L labels, warning 4 language 15 loading accessory 50 loading thick substrates 32, 53 loading thin substrates 32, 53 M margins changing 81 specification 85 media presets ing 59 memory specifications 85 O order accessories 83 ink cartridges 80

ENWW

printheads 80 waste management system 80 P paper usage 74 physical specifications 85 porous substrates 23 power specifications 85 print resolution 84 printer states 81 printer's main components 5 printer's main features 5 printhead about 76 ordering 80 specification 84 printhead cleaner specification 84 printhead cleaning cartridge about 77 printhead cleaning container about 78 printhead cleaning kit 77 printing delays 81 printing faster 70 R rear view 7 resolution 84 restart the printer 12 restore factory settings 17 S safety labels 4 safety precautions 1 scanner usage 74 security 18 sleep mode wait time 16 specifications acoustic 86 environmental 86 functional 84 hard disk 85 ink supplies 84 margins 85 memory 85 physical 85 power 85 print resolution 84 substrate size 84

ENWW


statistics usage 74 usage per job 74 substrate add new 59 advanced settings 64 automatic load 27 change settings while printing 64 displaying information 56 edge holders 49 load cut sheet 33 load onto spindle 23 load textile 50 loading accessory 50 manual load 30 overview 19 porous 23 print on both sides 54 settings 60 storage 58 ed families 20 take-up reel 34 tips 19 unload 33 substrate length tracking 57 substrate sizes (max & min) 84 T take-up reel motor 8 using 34 turn the printer on/off U units of measurement

11 16

W warning 3 warning labels 4

Index

91

Hp Designjet L26500 - Manual 6j1h3h

Overview 1s532p

More details 6h715l

Related Documents 2w1qw

Hp Designjet L26500 - Manual 6j1h3h

Hp Designjet L26500 Service Manual 6g4c29

Hp Designjet L26500 Service Manual.pdf 13152l

Designjet 5000 Manual 46h7

Hp Designjet T920 Service Manual 4z1s4h

Hp Designjet T2300 Service Manual 3414x

More Documents from "Printed Pixel, Inc." 4m42q

Hp Designjet L26500 - Manual 6j1h3h

Gestion De La Informacion Estadistica 176w3o

Paul Pierre In Paris Part1 2q603b

Hackear Wii 6v3v5j

Manual Ritmo-peso Perfeito - Portugues 3y2l5z

Biantara Bahasa Sunda m6c6a