Yellawood Greenhouse Design Plans 4e3y4a

TM

GREENHOUSE LUMBER 26 2” x 4” x 8’ 8 1” x 4” x 8’ 1 2” x 4” x 8’ 1 2’ x 4’ x 3/4”

YellaWood® treated lumber YellaWood® treated lumber YellaWood® treated lumber YellaWood® exterior treated plywood

FASTENERS 2 manufacturer recommended hinges 10d manufacturer recommended nails (as needed) 1 3/4” manufacturer recommended metal fasteners with neoprene washers (as needed) OTHER 1 30” x 80” hot-dip galvanized or vinyl door 10 4’ x 8’ fiberglass s NOTE: Check with the local building department to determine proper fastening to ground. TIP: Use water repellent or stain with water repellent when your job is finished to help protect your pressure treated wood from splitting, checking, and warping. TIP: If the bottom plates are in with the ground, you may want to consider using .40 ground approved 2x4s. TIP: In some applications you may use screws instead of nails for better hold down power.

Find your local YellaWood® dealer at YellaWood.com

FASTENER AND HARDWARE INFORMATION SHEET FOR MICRONIZED COPPER TREATED PRODUCTS

Micronized copper treated products (micronized copper quaternary or micronized copper azole) offer treated pine with micronized copper preservatives exhibits corrosion rates on metal products similar to CCA pressure treated wood and untreated wood. • For interior or exterior applications – Use fasteners and hardware that are in compliance with the manufacturer’s recommendations and the building codes for their intended use. As with any good design and construction practices, treated wood should not be used in applications where trapped moisture or water can occur. Where design and/or actual conditions allow for constant, repetitive or long periods of wet conditions, only stainless steel fasteners should be used. • For exterior applications – The following minimum galvanization levels may be used for connectors, joist hangers, fasteners and other hardware that are placed in direct with exterior applications of micronized copper treated wood: Fasteners - nails, screws, etc. ASTM – A 153 (1 oz/ft2 ) Hardware - connectors, joist hangers, etc. ASTM – A 653 G90 (0.90 oz/ft2 ) The effects of other building materials within a given assembly, along with environmental factors, should also be considered when selecting the appropriate hardware and fasteners to use for a given project containing treated wood. Stainless Steel fasteners and hardware are required for Permanent Wood Foundations below grade and are recommended for use with treated wood in other severe exterior applications such as swimming pools, salt water exposure, etc. - Type 304 and 316 are recommended grades to use. • Aluminum building products may be placed in direct with YellaWood® brand products used for interior uses and above ground exterior applications such as decks, fencing, and landscaping , direct of micronized copper treated products and aluminum building products should be limited to code-compliant construction applications that provide proper water drainage and do not allow the wood to be exposed to standing water or water immersion. We recommend you the aluminum building products manufacturer for its recommendations regarding use of its aluminum products in with micronized copper treated wood in ground applications or when exposed to salt water, brackish water, or chlorinated water, such as swimming pools or hot tubs. Also check with the aluminum building products manufacturer regarding compatibility with other chemicals and cleaning agents. Osmose for further information on aluminum use in commercial, industrial, and specialty applications such as boat construction.

IMPORTANT INFORMATION

• Consult the end tag to determine which preservative or preservative system was used in the treatment of that particular product. Micronized copper treated products may be used in direct with aluminum building products when limited to code-compliant construction applications that provide proper water drainage and do not allow the wood to be exposed to standing water or water immersion. • Use fasteners and other hardware that are in compliance with building codes for the intended use with micronized copper treated products. • Do not burn preserved wood. • Wear a dust mask and goggles when cutting or sanding wood. • Wear gloves when working with wood. • Some preservative may migrate from the treated wood into soil/water or may dislodge from the treated wood surface upon with skin. • Wash exposed skin areas thoroughly. • All sawdust and construction debris should be cleaned up and disposed of after construction. • Wash work clothes separately from other household clothing before reuse. • Preserved wood should not be used where it may come into direct or indirect with drinking water, except for uses involving incidental such as fresh water docks and bridges. • Do not use preserved wood under circumstances when the preservative may become a component of food, animal feed or beehives. • Do not use preserved wood as mulch. • Only preserved wood that is visibly clean and free of surface residue should be used. • If the wood is to be used in an interior application and becomes wet during construction, it should be allowed to dry before being covered or enclosed. •

• Mold growth can and does occur on the surface of many products, including untreated and treated wood, during prolonged surface exposure to excessive moisture conditions. To remove mold from the treated wood surface, wood should be allowed to dry. Typically, mild soap and water can be used to remove remaining surface mold. For more information visit www.epa.gov. • Projects should be designed and installed in accordance with federal, state and local building codes and ordinances governing construction in your area, and in accordance with the National Design

Disposal Recommendations: boilers in accordance with federal, state and local regulations.

YellaWood® brand pressure treated products are treated with micronized copper quaternary or micronized copper azole using the MicroPro® copper preservative process. Ask dealer for warranty details. Great Southern Wood Preserving Incorporated, its s, subsidiaries and TSO providers, use Osmose, Inc. wood preserving products, methods, systems and technology in the treatment of YellaWood® brand products. For more information visit www.osmosewood.com. For important handling and other information concerning our products or for a copy of the YellaWood® brand Material Safety Data Sheet (MSDS), please visit us at www.greatsouthernwood.com or write us at P.O. Box 610, Abbeville, AL 36310. YellaWood® and the yellow tag are federally ed trademarks of Great Southern Wood Preserving Incorporated. The Great Southern Wood Preserving Incorporated logo is a trademark of Great Southern Wood Preserving Incorporated. MicroPro® is a federally ed trademark of Osmose Incorporated. The MicroPro® Wood Treatment Process is certified under SCS’s Environmentally Preferable Product (EPP) program based on Life-Cycle Assessment. Great Southern Wood Preserving Incorporated makes no warranties expressed or implied as to the fitness for a particular purpose of this plan.

©2009