Winchester 1200 Military Manual 5z1j6p

CHAPTER 3 OPERATOR AND ORGANIZATIONAL SERVICE AND MAINTENANCE

INSTRUCTIONS

Section I. SERVICE UPON RECEIPT OF MATERIEL 3-l. General Refer to table 2-l. Table S-1. Service Upon Receipt of Materiel Sl

1 2 3 4

Refwence

.-lotion Remove shotgun and items from container. Remove VCI, clean and lubricate. Inspect for: Missing parts Proper assembly Function, using once-fired empty round.

Paragraph 3-4 Figure B-2 Figures 2-2 and 2-3.

Caution: Do not use live ammunition when hand functioning weapon.

Section II. REPAIR PARTS, SPECIAL TOOLS AND EQUIPMENT 3-2. Special Tools and Equipment a. Opwcztor. Refer to appendix B, section II. b. OrganizathzaZ. Refer to appendix B, section V.

3-3. Repair Parts a. Operator. None authorized. b. Organizational. Refer to appendix B, section IV.

Section Ill. LUBRICATION INSTRUCTIONS 34. General a. Refer to table 3-2 for cleaning and lubrication materials. Use stock numbers for requisitioning purposes. b. Refer to table 3-3 for usual lubrication instructions. c. Refer to table 3-4 for lubrication instructions for unusual conditions. Table J-Z. Materials Rkquired for Maintenance Functions E’SN

6850-965-2332

8

1tc*r

CARBON REMOVING COMPOUND: (P-C-111) (5 gal. pail).

IJSN

6850-224-665’7

5350-221-0872

8010-582-5382

8010-221-0611

Itew CLEANING COMPOUND, RIFLE BORE: small arms bore cleaner, solution (CR) (6 oz can). CLOTH, ABRASIVE : crocus, ferric oxide and quartz, jeancloth-backing, closed coating, 9 w, 11 lg, 50-sh-sleeve (CA). LACQUER: black (jet) lusterless type I, color 37038 (16 oz aerosol can) Spec TT L 9950 type I nitrocellulose base. LINSEED OIL, RAW: (TT-L00215) (1 gal. can). LUBRICATING OIL, GENERAL PURPOSE : (PL special). AGO 20027A

/ten1

FSN

4 02 can. 1 qt can. LUBRICATING OIL, WEAPONS: (LAW) for below zero operations (1 qt can). RAG, WIPING: cotton for general purpose use (50 lb bale). SEALING COMPOUND : 150/375 in-lb locking torque lo-15 viscosity, gun color MIL-S-22473 Grade AA (lo-CC bottle).

9150-273-2389 9150-231-6689 9150-292-9689 7920-205-1711 8030-081-2341

Table 3-4. Lmbrication Instructions for Unusual Conditions T!~pe

Note.

Reduce lubrication intervals to less then daily, if inspection indicates rust or corrosion.

Extreme cold (below 0°F.)

Make certain all components are dry and free from condensation before applyine luhriention. Also refer to TM !I-20i.

Table $4). Lubrication Instructions for Usual Conditions Procedure Note.

Shotmn will ONLY be disassembled for cleanincr and lubrication into major groups and assemblies when a THOROUGH INSPECTION indicates the weapon is dirty and c o n t a m i n a t e d a n d t h a t functionina of the weapon would he impaired.

Clean bore and locking lug area of the barrel assembly and other powder-fouled surfaces with rifle bore cleaning compound (CR). Remove all foreign matter. Thoroughly dry bore and chamber, including the locking lug area. Lightly oil bore, barrel extension, and external surfaces of the weapon, using general purpose lubricating oil (PL special).

1

2 3

which are intended for infrequent firinn, or *re placed in *rms rooms for safekeepinn for prolonW periods, will have R film of aeneral purpose luhricatinrc oil (PL special) applied to the internnl and external ~r‘oups immediately after inspection a n d elennina. Special attehtion should be civen to bore, chamber, and lockinn hart area.

Hot and dry

For general clenninz procedures. refer to TM 9-208-l and TM 9-247.

5 6 7

All components affected by powder fouling will be cleaned with carbon removing compound (P-C-111). Warning: Avoid skin . The compound should be washed off thoroughly with running water if it comes in with the skin. A good lanolin base cream, after exposure to compound, is helpful. The use of gloves and protective equipment is recommended. Wipe or blow dry and oil with general purpose lubricating oil. Thereafter, clean and oil as required. Wipe wooden components with slightly oiled rag. Remove surplus oil with a dry cloth. Apply a light coat of linseed oil and rub into wood with heel of hand. Note.

With patch and cleaning rod. remove oil from bore and chamber of barrel assembly before firina.

Inspect shotgun frequently for rust. Lightly oil with general purpose lubricating oil (PL special). If exposed to salt air, high humidity or moisture, more frequent cleaning and oiling will be required to protect components. Note. Weapons

Note.

4

Lubricate with weapons lubricating oil (LAW). Keep weapon protected as much as possible.

Note.

Hot and humid

step

I’roreifurc

of Climate

Clean shotgun daily (or as required). In sandy or dusty areas, wipe weapon free of oil to prevent sand and dust from collecting on the outside and working components. No&. Protect weapon from wuter while fordina. if possible.

Immersion in water.

During deep fording, it is possible for the weapon to become completely submerged. If this occurs, eject the round from the chamber to allow water to run from the bore. Normally, if the round is left in the chamber, it will form a vacuum and will not allow the water to drain freely. If the above condition occurs, the weapon should be wiped dry as soon as possible. If inspection reveals rust or corrosion is evident, the weapon should be turned in to organizational maintenance for complete cleaning and lubrication of all components.

Section IV. PREVENTIVE MAINTENANCE CHECKS AND SERVICES 3-5. General a. Refer to table 3-5. AGO 20027A

b. All deficiencies, shortcomings, and corrective action taken will be recorded on DA Form 2407 at the earliest opportunity. 9

Table f-5. Preventive Maintenance Checks and Servaces

lOperator f

Daily

A-

s h: $ z

B-before operation D-during operation

OW.

w -

M

1 2 3

X X X

X X

X

X X

4

X

X

X

Aw-2ttgk,ytion

M-monthly

Item to be inspected

Reference

X

Gun Shoulder Stock Group

5

X

X

X

Magazine Cap ~.

6

X

X

X

Barrel and Bayonet Band As; sembly.

7 8

X X

X X

X X

Trigger Guard Pin ~~ ..~~ _~. Trigger Guard Group ._.. . . .

9

X

X

X

10

X

X

X

Slide Arm Bridge Retaining Screw. Fore End Group _

11

X

X

X

Breech

12

X

X

X

E j e c t o r . ..~.....__...__._

Bolt

~.

Group _

Warning: Before starting inspection, make certain that weapon is cleared. Inspect the chamber and magazine tube to insure that both are empty. Determine that no ammunition is in position to be introduced. N o t e . Weekly and monthly inspections apply only if weapon is used drily. Clean and lubricate ..~__....~...____.____--..------___-----..._.. Actuate controls _....~~_.....__.________--.._.--_-____.__--....__ Check for missing parts, proper assembly of weapon and if major groups and assemblies are properly secured. Determine that sling is secured to gun shoulder stock group and bayonet band assembly. Stock cannot be cracked or loose. Structural strength must not be impaired. Check for burs, stripped threads, and if properly secured to m+gazinc tube. Bayonet band assembly must be secured to barrel assembly. Check for unusual pits or damage to bore of barrel assembly. Assure that bore is dry and free of obstructions before firing. Check for burs and if bent or loose _._~~.._____.~__~__ . . . . . . . . ..__. Check hammer, safety and trigger for proper operation. Actuate disconnector assembly for proper functioning. Check left hand and right hand slide arm for being bent or other damage. Check carrier assembly for freedom of movement. Check for stripped threads and damaged screw slot. Determine that slide arm bridge is secured to bolt slide. Check for proper functioning and cracks in fore end. Structural strength must not be impaired. Check slide arm extensions for excessive wear, burs or being bent. Slide arm extension cap must be secure to the slide arm extension. Check assembly slots on cap for burrs. Cam pin must be free of burrs. Breech bolt must have free movement in camways of receiver. Check protrusion of firing pin. Check extractor claw for damage. Check component for visible rust or corrosion. Check for burrs or being bent. Test weapon with dummy round or once-fired empty round to insure proper ejection of cartridge. Check ejector pin for being secure in receiver and if damaged.

Tables 3-3, 34 Figure 2-l Table 3-l and fig. B-2 Figure 6-2 Figure 5-l Figure 3-l I

Figure 3-2 Figure 5-3 Figures 5-7, 5-8 and 5-9 Figure 5-4 Figure 5-10

Figures 5-11, 5-12

Figures 5-5, 5-6

1 x x

X

Receiver and Magazine Group.. Magazine tube should be secured to the receiver. Check tube for dents, .‘Figure 5-13 burrs or damage which will restrict the cartridge. Check helical compression spring (magazine) for kinks, and magazine follower for being broken or burred. Check for rust and corrosion in components.

Section V. TROUBLESHOOTING

34. General Refer to table 3-6. Table $16. Troubleshooting

MalfuIietion

I

Probable ca”se

Corrective action

. For corrective action of malfunctions not listed in this table, refer to direct ~~Ml~kI~l.

Note.

Failure to fire

_

_

_

Failure to load

Pump shell into chamber.

Empty

Load magazine (step 2, fig. 2-2).

magazine

F a u l t y a m m u n i t i o n _. _

_ _ Pump out defective shell and use other ammunition.

Foreign matter in firing pin aperture of cam pin, bolt or bolt slide.

Clean applicable items (4, 8, or 9, fig. B-4 and table 3-3).

Operator fails to disengage safety. Foreign matter in safety aperture in trigger.

Disengage safety (step 1, fig. 2-3). Clean trigger (16, fig. B-3 and table 3-3).

Failure to move bolt slide fully forward.

Push fore end forward (step 3, fig. 2-2).

Failure to load or feed

Dbstruction in the chamber _ Defective carrier assembly . _ . . . Foreign matter in RH or LH slide arm s or magazine tube.

Clean receiver (table 3-3). Notify direct maintenance. Clean applicable items (2, 3, fig. B-3 and 28, fig. B-2).

Failure to function correctly

Foreign matter in bolt, bolt slide or safety well of trigger guard.

Clean applicable items or area (8, 9, fig. B-4 and 18, fig. B-3).

Section VI. MAINTENANCE PROCEDURES 3-7. Removal/Installation of Major Components a. Operator. Field stripping of weapon into major groups and assemblies is not authorized. 21. Organizational. Refer to table 3-7. 3-8. Disassembly/Assembly of Major Components a. Operate.

None authorized.

b. Organizational. Refer to table 3-7. Note. White arrows shown on illustrations indicate disassembly, black arrows indicate assembly. 12

3-9.

Cleaning, inspection and Repair

a. Clsmin~g instrwtions. Refer to table 3-3.

B. Inspection. Refer to tables 3-6 and 3-7. c. Repair. ( 1) Replace- bayonet band screws or bayonet band assembly if damaged or unserviceable.

(2) No other repair parts are authorized for organizational maintenance. If necessary, evacuate shotgun to direct maintenance personnel. AGO ZOW7A

.

Table 3-17. Operator and Organizational Maintenance Guide fov Winchester Shotgun,

Model 1200 Group of assembly

Removal/installation

Disassembly assembly

Cleaninrr. inspection and repair

-

FirC

CLEANING Shotgun .._ . . . . __..__.___

Refer to paragraph 3-4. INSPECTION

Shotgun

Visually inspect the components for wear, cracks, dents and damage. Make certain all parts are properly installed and in working condition.

.._

__

B-2 thru B-4

REPAIR S h o t g u n

Remove all traces of rust or scarred areas from finished surfaces with cloth, moistened with light oil. Tables 3-3 thru 3-6.

Gun shoulder stock group

Vote.

Stock WOUI) will not be removed from receiver and magazine YIBUP.

Barrel and bayonet band assembly.

Figures 3-l and 3-2.

Trigger guard group

16, figure B-2,

Tables 3-3 thru 3-5.

Fore

18, figure B-2.

Tables 3-3 thru 3-5.

end

group

~.

_

Paragraph 3-9c. Remove burs on barrel assembly by stoning (Organizational maintenance only).

Vutc.

l*‘ore end PROUD will not be removed from receiver and maaazine croup.

Breech bolt group _

22, figure B-2.

Tables 3-3 thru 3-5.

Receiver and magazine group.

28, figure B-2.

Tables 3-3 thru 3-6.

mission of the copyright owner, Olin Mathicson ester - Western Division, New Haven, Corm.

BAND ASSEMBLY

WISE.

REMOVEjlNSTALL CAP.

REMOVE/INSTALL BARREL AND BAYONET BAND ASSEMBLY. WE 60052

Figure 3-l. Removal/installation of barrel and ba.yonet band assembly. AGO 20027A

13

REMOVE/INSTALL SCREWS.

PLASTIC ‘HAMMER

INSTALL BAYONET BAND ASSEMBLY.

REMOVE BAYONET BAND AS%f+faLY.

Figure Y-2.

14

Renzoval/installatiOrf

of

bawnct

band assembly.

WE 60053

CHAPTER 4 DIRECT AND GENERAL MAINTENANCE INSTRUCTIONS

Section I. REPAIR PARTS, SPECIAL TOOLS AND EQUIPMENT 4-l. Special Tools and Equipment

4-3. Improvised Tools and Equipment

Refer to appendix B.

Refer to table 4-l.

4-2. Maintenance Repair Parts Refer to appendix B. Table 4-l. Improvised Tools

Item

TOOL, assembling cam pin

Reference

~.

TOOL, disassembling and assembling slide arm extension cap.

Figures 4-l and 5-12

Required for

To assemble cam pin to breech bolt and bolt slide.

~.

To disassemble and assemble slide arm extension cap to front end of slide arm extension assembly.

Figures 4-2 and 5-10

-----,-

i

1- 3/4 t-

i-43 w

-----1 _ I

I^

DRILL R/OD OR COLD ROLL STEEL NOTE: ALL DIMENSIONS SHOWN ARE IN INCHES.

WE 60216

Figure 4-f. Improvised tool for assembling cam pin.

AGO 20027A

15

BODY: BLADE: RIVETS:

6-l/2 LONG BY l/4 THICK COLD ROLL STEEL. 1 INCH BY l/8 X l-1/2 TOOL STEEL, FLAT STOCK. 3/16 BY l/2 L O N G .

- I I - -

NOTE: ALL DIMENSIONS SHOWN ARE IN INCHES.

1/8

WE 60215

Figure 4-2. Improvised tool for disassembling and assembling slide arm extension cap.

Section II. TROUBLES,HOOTING 4-4. General

Troubleshooting malfunctions, probable causes,

and corrective actions for the 12 Gage, Shotgun, Riot Type, Winchester, Model 1200 are listed in table 4-2.

Table 4-2. Troubleshooting Malfunction

Failure to fire

Probable cause

Failure to feed

Short or broken firing pin ~. Foreign matter in firing pin aperture in bolt. Broken hammer Bent or damaged helical torsion spring (hammer). Burred or broken trigger spring N&u. l’rirrter aw%w is H c o m p o n e n t o f

Corrective action

Repair magazine tube (28, fig. B-2). If unserviceable, turn in weapon for replacement. Replace (2, fig. B-4). Zlean aperture in bolt and bolt slide (8, 9, fig. B-4). Replace (13, fig. B-3). Replace (12, fig. B-3). Remove burs or replace sear bracket assembly (9, fig. B-3).

saw bracket assembly.

Broken sear Broken triggei Foreign matter in sear notch of hammer. Burred trigger guard or foreign mat in safety well. Damaged disconnector assembly or helical torsion spring (disconnector). 16

Replace sear bracket assembly (9, fig. B-3). Replace (16, fig. B-3). Glean sear notch on hammer (table 3-3 and 13, fig. B-3). Repair t.rigger guard or clean safety well (18, fig. B-3 and table 3-3). Replace, 7, 8, fig. B-3).

AGO 20027A

Table 4-e. Troubleshootirlg-Continued Probable cause

Malfunction

Failure to extract or eject

Worn, burred or broken extractor Bent or broken helical compression spring (extractor). Burred or bent ejector Broken or bent carrier assembly Corroded magazine follower

corrective action Replace (7, fig. B-4). Replace (6, fig. B-4).

Repair or replace (24, fig. B-2). Replace (4, fig. B-3). Failure to load or feed Clean (table 3-3) or replace magazine follower (27, fig. B-2). D a m a g e d m a g a z i n e t u b e _ Turn in weapon for replacement. Broken or kinked helical compres- Replace (26, fig. B-2). sion spring (magazine). Clean magazine tube (28, fig. B-2). Foreign matter in magazine tube D o u b l e feeding _ _. _ ~. _ Burred or broken LH or RH slide Replace (2, 3, fig. B-3). arm s. Note. Cartridge Stop and cut off are eomwnents of above items.

Failure to function correctly

Foreign matter under LH and RH slide arm s. Damaged disconnector assembly _ Burs or foreign matter in bolt slide and bolt. Broken or bent disconnector or helical torsion spring (disconnector). Burred or bent slide arms

Notr.

Clean (table 3-3) (2, 3, fig. B-3). Replace (7, fig, B-3). Repair (8, 9, fig. B-4) or clean (table 3-3). Replace (7, 8, fig. B-3). Repair or replace slide arm extension (21, fig. B-2).

Slide arms are components of slide a r m cstenrion rcswmbly.

Broken or burred cam pin Weak or damaged firing pin Safety sticks ~. ’ Burred safety _ _. _ Damaged hammer housing

Section III. INSPECTION 4-5. General Refer to

AGO 20027A

TB 9-1000-247-35.

Repair or replace (4, fig. B-4). Replace (2, fig. B-4). Repair (14, fig. B-3). Repair (14, fig. B-3). Replace (17, fig. B-3).

CHAPTER 5 REPAIR INSTRUCTIONS

Section I. GENERAL MAINTENANCE 5-1. General

(1) Parts will be replaced, when unservice-

This section provides instructions on general maintenance procedures. 5-2. General Repair Methods

a. Disassembly and Assembly Procedures. (1) In disassembling the shotgun, remove the major groups and assemblies whenever possible. Refer to figure B-2 and paragraph l-3b. Groups and assemblies may be disassembled, as necessary, into individual parts. (2) Complete disassembly of a unit is not always necessary in order to make a required repair or replacement. Good judgment should be exercised to keep disassembly and assembly operations to a minimum. (3) During assembly, assemblies and groups should be assembled first, then installed to form a complete unit. Lubricate frictional (sliding) surfaces before assembly. b. Replacement of Parts.

able. (2) If screws and washer are damaged, they will be replaced. (3) All springs should be replaced if they are broken, deformed, fail to function properly, or fail to meet specific requirements. 5-3. Cleaning and lubrication a. Cleaning. Refer to figures 5-14 thru 5-16. b. Lubrication. Prior to assembly of major groups and assemblies, all components will be lubricated in accordance with table 3-3. 54. Finished Surfaces a. All metal surfaces subjected to wear and abrasions and which reflect light or will be subject to rust or erosion, will be treated with black lacquer. b. All surfaces must be clean and dry prior to spraying. Allow two hours for lacquer to dry.

Section II. MAINTENANCE OF SHOTGUN S-5. Specific

Refer to table 5- 1.

18

AGO 20027A

Table 5-1. Guide to Maintenance Function of Shotgun M

Item

Removal/installatiin

Cleaning, inspection and repair

Diussembly/awembly

8

s

Iota All pins should be removed from left to right installed right to left when applicable.

Gun shoulder stock group Magazine cap ~~. ~. Barrel and bayonet band assembly Trigger guard group ~.

Figure 5-l ~.~. __ Figure 3 l %gure3-1 _~.~__...__ ?igures 5-3 and B-2 _

Figure B - 2 _.__ _.____.. . . . ..__... Figure B - 2 __________..__ . . . .._...

3 - 2 a n d 5 - 2 _. . . _. _. Figures 5-7, 5-8, and 5-9 ___.. ----. l&e. To uraemble disconnector s p r i n g , t u r n Figures

spring upright so tail of spring is engaged in its proper position in trigger guard pin hole slot. Turn disconnector to upright position and slide front of spring under ledge on disconnector. Compress front of disconnector downward until disconnector button is in line with slot in trigger guard. Hold in this position and push inward until disconnector pin engages hole in opposite

Figure 5-4 ~~ .~~..~_.~~~.~. .~~ b’ote. When barrel and bayonet band assen

Fore end group

Refer to figures 5-14 thru 5-16 for cleaning instructions. Repair Repair Repair Repair

(para (para (para (para

5-2) 62) 5-2) 5-2)

Vote.

If new trigger assembly is installed, it must be adjusted to fit as follows:

a.

With the safety in safe position and .rigger pulled, check the trigger thmugb trig!er stop pin hole with 0.252040005 diameter ,in. b. With the safety in safe position and trigrer pulled, adjust trigger adjustment screw Nithin 0.003-0.005 of sear. Break off end of screw end apply s e a l i n g c o m p o u n d .

side of sear bracket and hammer housinrr. Figure 5-10 ___..___.._ . . . .._._...

Repair (para 5-2)

Figure 5-11,5-12 _____ ___..~.....

Repair (para 5-2)

bly have been removed do not slam th fore end forward or pull the triage] allowing hammer to fall. This may jaz the action, making necessary the remow of trigger guard end the recocking of th hammer by hand.

Breech bolt group Receiver and magazine group

.~~

Figure 5-4 ._~_. ..~..~.~..

Figures 5-5, 5-6 and 5-13 . . _. _ _ Vote. When breech bolt group is removed, the ejector will fall free of the pin in the receiver.

CAUTION: IF SCREWDRIVER IS USED, CARE MUST BE TAKEN TO INSURE THAT SCREWDRIVER IS IN SLOT IN BOLT AND NOT BETWEEN HEAD OF BOLT AND WALL 06 STOCK. IF PRESSURE IS APPLIED TO SCREWDRIVER WHEN IN LATTER POSITION, IT WILL BREAK GUT THE WALL OF THE STOCK.

special permission ight owner, Olin Winchester - Western Division, New Haven, Conn.

SCREW

REMOVE/INSTALL BUTT PLATE SCREWS AND BUTT PLATE.

R EMOVE/INSTALL MACHINE BOLT AND LOCK WASHER.

Reprinted by special permission of the copyright owner, Olin Mothieson Chemical Corp., Winchester - Western Division, New Haven, Conn.

REMOVE/INSTALL STOCK WITH SWNEL

ASSEMBLY.

REMOVE/INSTALL SCREWS AND SWIVEL ASSEMBLY. WE 60057

Figure 5-l. Removal/installation of gun shoulder stock.

20

A G O 20027A

REMOVE COUNTERC LOCKWISE. INSTALL CLOCKWISE.

Figure 5-2. Removal/installation of front sight.

Reprinted by special permission of the copyright owner, Olin Mathieson Chemical Corp., Winchester - Western Division, New Haven, Corm.

NOTE. INSTALL TRIGGER GUARD GROUP TO INSERTING FRONT FND OF RIGHT AND LEFT HAND SLIDE ARM S INTO SLOTS AT FRONT END OF RECEIVER PUSHING REAR END OF GUARD GROUP DOWN UNTIL PROPERLY SEATED (DO NOT FORCE).

PFCFIGFR RY ,.C__.

_..

.

_.

_

_

_

-._.,,. -.__._

REMOVE TRIGGER GUARD PIN.

INSTALL TRIGGER GUARD PIN.

THE HAMMER SPRING MUST FIT IN RETAINING NOTCH OF SAFETY. -dr REMOVE/INSTALL TRIGGER GUARD GROUP. WE 50059

Figure 5-3. Removal/installation of trigger guard group.

AGO 20027A

21

REMOVE FORE END AND BREECH BOLT GROUPS.

REMOVE SLID’ ARM BRIDGE RETAINING SCREW.

Reprinted by special permission of the copyright owner, Olin Mathieson Chemical Corp., Winchester - Western Division, New Haven, Corm.

FORE END GROUP

SEPARATE BREECH BOLT GROUP FROM FORE END GROUP.

Figure T-4. Removal/insta~lation

WE 60060

of fore evd and b,cech bolt groups.

Reprinted by special permission of the copyright owner, Olin Mathieson Chemical Corp., Winchester - Western Division, New Haven, Cow.

Figarc

5-5. RC~OUC e.iccto).. AGO

20027A

Reprinted by special permission of. the copyright owner, Olin Mathieson Chemical Corp., Winchester - Western Division, New Haven, Corm.

INSTALL SLIDE ARM RETAINING SCREW.

LOCATION OF EJECTOR AND EJECTOR SUPPOR PIN. BREECH BOLT OMITTED FOR CLARITY.

-_-

-

SEAT EJECTOR ON EJECTOR PIN.

‘\

PLACE EJECTOR BETWEEN BOLT SLIDE AND FRONT END OF LEFT SIDE OF RECEIVER.

BREECH BOLT GROUP.

\$

FORE END GROUP

INSTALL BREECH BOLT AND FORE END GROUPS AND EJECTOR IN RECEIVER.

INSTALL BREECH B O L T GROUP ON FORE END G R O U P . WE 60051

F i g u r e 5-6. Install breech bolt group, ejector and slide arm bridge retaining screw.

23

REMOVE/INSTALL LEFT HAND SLIDE ARM .

REMOVE/l NSTALL TRIGGER STOP PIN SCREW. CAUTION: THE CARRIER PIN IS A COMPONENT OF RH SLIDE ARM . WHEN REMOVING , PLACE THUMB OR FINGER OVER CARRIER ASSEMBLY TO PREVENT LOSS OF CARRIER PLUNGER AND SPRING WHEN THE PIN IS REMOVED.

S

U

P

P

O

R

T

-

CARRIER ASSEMBLY

*

REMOVE/INSTALL RIGHT HAND SLIDE ARM .

REMOVE/INSTALL CARRIER ASSEMBLY, CARRIER PAWL PLUNGER AND HELICAL COMPRESSION SPRING (CARRIER).

\ \\

,,c--.

Reprinted by special permission of the copyright owner, Olin Mathieson Chemical Corp., WinChester - Western Division, New Haven, Coon.

1. PUSH SAFETY TO “OFF” (UNLOCKED) POSITION. 2. PULL TRIGGER.

NOTE: HOLD HAMMER WITH THUMB AND SLOWLY RELEASE SPRING PRESSURE WHEN TRIGGER IS PULLED.

RELEASE HAMMER.

Figure 5-7. LXsassembly/asscmbly

WE 60065

of trigger guard group (1 of 3). AGO 20027A

24

Reprinted by special permission of the copyright owner, Olin Mathieson Chemical Corp., WinChester - Western Division, New Haven, Corm. NOTE: THE RETAINING PIN FOR SEAR BRACKET ASSEMBLY ’ IS A COMPONENT OF DISCONNECTOR ASSEMBLY. PLACE THUMB OR FINGER OVER SEAR BRACKET AS IT IS UNDER PRESSURE OF TRIGGER SPRING. I /’ i

SPRING _

_._4+ DISCONNECTOR ASSEMBLY

I

,/

,,’

L I N E SHOWS PROPER POSITION OF DISCONNECTOR SPRING AT ASSEMBLY. LOCATION OF DISCONNECTOR AND SPRING.

REMOVE/INSTALL SEAR BRACKET ASSEMBLY.

REMOVE/INSTALL DISCONNECTOR ASSEMBLY AND HELICAL TORSION SPRING (DISCONNECTOR).

REMOVE/INSTALL HAMMER PIN.

NOTE: WHEN ASSEMBLING HAMMER PIN, HAMMER SPRING S AND HAMMER, NOTE THAT THESE COMPONENTS EACH CONTAIN A FLAT CUT, AND MUST BE IN PROPER ALINEMENT WITH HAMMER HOUSING AT TIME OF ASSEMBLY. DO NOT DRIVE HAMMER PIN FLUSH WITH THE HOUSING. IT MUST PROTRUDE APPROXIMATELY l/R INCH TO ALLOW PROPER FUNCTIONING OF DISCONNECTOR.

REMOVE/INSTALL

HAMMER

GROUP.

F i g u r e 5 - 8 . Disassembl?J/nssemblU

of

tliggw gunwl

g,‘oup

(2 of 3).

25

NOTE: TO INSTALL PRESS S IN WITH THUMB AND FINGER

Reprinted by special permission of the copyright owner, Olin Mathieson Chemical Corp., Win Chester - Western Division, New Haven, Con

THIN-BLADED

REMOVE/l NSTALL HAMMER SPRING S.

SEPARATE/ASSEMBLE HAMMER AND HELICAL TORSION SPRING.

NOTE: REMOVE FROM RIGHT 1 LEFT AS ONE END OF PIN IS SERRATED WITH LIGHT TAPER. REMOVE/l NSTALL SAFETY

REMOVE/INSTALL TRIGGER PIN.

ER HOUSING

TRIGGER GUARD

“I

b--

PIN

REMOVE/INSTALL TRIGGER.

NOTE: IT MAY BE NECESSARY TO USE- SOtiE FORCE WHEN REMOVING HOUSING. PULL UP AND OUT FROM TRIGGER GUARD. DO NOT PRY. REMOVE/INSTALL HAMMER HOUSING.

WE 60068

Figure 5-9. Disassembly/assembly of trigger guard group (3 of 9). 26

AGO

20021A

Reprinted by special permission of the copyright owner, Olin Mothieson Chemical Corp., Winr - Western Division, New Haven, Corm.

DISASSEMBLY/ASSEMBLY

REMOVE/INSTALL SLIDE ARM CAP.

REMOVE/INSTALL FORE END. WE 60062

Figure

5-10.

Disassembly/assembly of jo,re end group.

27

MAKE CERTAIN THAT THE TAB OF THE BRIDGE DROPS DOWN BETWEEN THE FLANGE AND THE HEAD OF FIRING PIN TO RETAIN IT IN PLACk. CAUTION: HOLD THUMB OVER FIRING PIN TO PREVENT PIN AND SPRING FROM BEING LOST UNTIL BRIDGE IS REMOVED OR INSTALLED. INSTALLATION:

TAB

REMOVE/INSTALL SLIDE ARM BRIDGE.

SLIDE ARM BRIDGE INSTALLED.

Reprinted by special permission of the copyright owner, Olin Mathieson Chemical Corp., Winchester - Western Division, New Haven, Conn. REMOVE FIRING PIN AND SPRING.

PIN

.“_’

REMOVE CAM PIN.

CAUTION: AFTER CAM PIN HAS BEEN REMOVED. PLACE THUMB OR FINGER OVkR THE REAR END OF THE BREECH BOLT BEFORE REMOVING PUNCH. FIRIN G PIN COLLAR AND s EXTRACTOR SPRING ARE UNDER PRESSURE AND WILL FLY OUT IF NOT PROTECTED. \

&

BREECH BOLT

EXTRkCTOR

FIRING PIN COLLAR RETAINING FIRING PIN COLLAR AND EXTRACTOR SPRING DURING REMOVAL OF BREECH BOLT COMPONENTS.

Figure 28

5-11. Diaassembl~/asscmbly

REMOVE FIRING PIN COLLAR, HELICAL COMPRESSION SPRING, EXTRACTOR AND BREECH BOLT. WE 60063

of breech bolt group (1 of 2). A G O 20021.4

INSTALL HELICAL COMPRESSION SPRING ON FIRING PIN. INSERT SPRING AND PIN IN BREECH BOLT FROM REAR, MAKING CERTAIN THAT FIRING PIN ES THRU -HOLE IN CAM PIN. COMPRESS FIRING PIN. \

INSTALL FIRING PIN AND HELICAL COMPRESSION SPRING (FIRING PIN).

NOTE: ALINE CAM SLOT WITH CAM PIN HOLE IN THE BOLT BY LIFTING BOLT SLIDE SLIGHTLY. START END OF CAM PIN NEAREST FIRING PIN HOLE INTO THE BOLT. THE HOLE IN CAM PIN MUST BE IN LINE WITH THE LONG AXIS OF BOLT. USING DRIFT PIN OR (IMPROVISED) CAM PIN ASSEMBLY TOOL, PUSH FIRING PIN COLLAR DOWN TO COMPRESS THE HELICAL COMPRESSION SPRING.

SEAT CAM PIN.

CAM PIN ASSEMBLY

CAUTION: DO NOT HAVE YOUR FACE IN LINE WITH BACK END OF BOLT DURING THIS OPERATION. PUSH CAM PIN IN AS FAR AS IT WILL GO. AT THIS POINT COLLAR MAY PREVENT PIN FROM SEATING FULLY. IF NECESSARY, USE A SMALL ROD OR SCREWDRIVER TO DEPRESS THE UPPER EDGE OF COLLAR WHILE SEATING CAM PIN. BOLT SHOULD BE BOTTOM SIDE UP WITH EXTRACTOR ON RIGHT HAND SIDE. LOOKING THRU BOLT FROM REAR, CLEAR AGE FOR FIRING PIN SHOULD BE VISIBLE. INSTALL CAM PIN.

Reprinted by special permission of the copyright owner, O’in Mothieson Chemical Corp., Winchester - Western Division, New Haven, Corm.

BREECH BOLT

EXTRACTOR

INSTALL BREECH BOLT.

Figzwe 5-M Disaeeembly/assembl~

INSTALL EXTRACTOR, SPRING AND COLLAR.

of breech bolt group (2

of 2).

29

CAUTION: WHEN REMOVING

\

MAGAZINE SPRING FROM

-. \

\

“?

PLUG

I/

REMOVE MAGAZINE PLUG.

INSTALL MAGAZINE PLUG.

Reprinted by special permission of the copyright owner, Olin Mothieson Chemical Corp., Winchester - Western Division, .N Haven, Corm . MAGAZINE 1

E t

NOTE: DO NOT ATTEMPT TO REMOVE MAGAZINE FROM RECEIVER AS THIS IS A FACTORY ASSEMBLY OPERATION ONLY. PLUG R E M O V E / I N S T A L L P L U G A N D H E L IC

AL COMPRESSION SP R I N G (M AG A Z I N E) .

FOLLOWER

,,

REMOVE 6 REMOVE/INSTALL MAGAZINE FOLLOWER. WE 60069

30

Figure 5-13. Disasscmbl~/assembl~

o f mccgazitle.

XGO

20027A

Reprinted by

special

permission of

the

copyright

A - CLEANING MAGAZINE TUBE.

B - CLEANING BARREL.

C - CLEANING SLIDE ARM EXTENSION.

WE 60071

31 ,\c,o ?n027A

BRUSH

A _ LUBRICATING

I

RECEIVER

RECEIVER AND MAGAZINE TUBE*

B _ LUBRICATING SLIDE ARM EXTENSION. \

‘> >

C _ L(,BR\CAT]NG

BAND ASSEMBLY

BARREL AND BAYONET BAND ASSEMBLY. h

, ..^ .

_^^,,n

D _ LUB RICATING BREEC

tIGGER GUAKU

rnr\,,D*

Vnuu’-

WE 60070

:H BOLT GKUur.

Figure 5-I 5.

32

E - LU B RICATING Tr

Lubricating

instructic”s*

Aa 20021

NOTE: RURUNSEED OIL IN WOOD TO TREAT STOCK.

A.

STOCK WITH SWIVEL ASSEMBLY.

B. FORE END. WE 60072

Figure 5-16. Cleuniug and treating wooden components.

5-6. Functioning with Once-Fired Empty Rounds

Shotguns authorized to be repaired in the field

will be handfunctioned, using five once-fired empty rounds. Shotguns which fail in abovenoted test will be corrected by replacement of defective parts.

33

CHAPTER 6 MATERIAL USED IN CONJUNCTION WITH MAJOR ITEM

6- 1. General

This chapter contains information on materiel used with the major item. 6-2. Description a. Bayonet, Ml91 7’. (fig. B-l) It is used for

close , guarding of prisoners and riot duty. It can also be used as a general utility knife. It has a cutting edge of 14.81 inches at the bottom running from the point. The handle fits comfortably and has a knurled surface for a firm grip.

b. Sling, Ml. (fig. B-l) It hooks on the gun shoulder stock swivel and adapter swivel of bayonet band assembly and aids the operator in carrying and firing the weapon.

c. ScaBbard, Bayonet, M1.917. (fig. B-l) It is used to carry the bayonet Ml917 when not being used on the shotgun. 6-3. Removal/Installation a. Buyovet, M1917. Refer to figure 6-l. b. Sling, Ml. Refer to figure 6-2.

Figure F-l. Remove/install bayonet, B1917.

6 - 4 .

Disa&embly/Assembly

None authorized. 34

6-5. Cleaning, Inspection and Repair a. Cleaning. AGO

200279

ponents if required. Lubricate with general purpose lubricating oil. b. Irspection.

(2) Sling, ,441. Clean with dry cleaning solvent (SD), using cloth or bristle brush.

(1) Bayonet, M1917. (a) Should fit shotgun properly and latch securely. (b) If blade tip or grips are broken, replace. (c) Blade should be free of nicks, turned edges, rust and corrosion. (2) Sling, .Ml. (a) Inspect for required components such as hooks, fasteners, etc. (b) Check for cuts or other damage which will reduce strength or protective qualities. (c) Examine corners, seams and edges closely. (3) Scabb~ard, Bayonet, M1917. (a) Metal parts should be dark. Repaint if required). (b) Spring should hold bayonet when inserted in scabbard. (c) Loops or hooks for attaching to belt should not be damaged. They will be securely fastened to the metal top plate.

(3) Scabba(rd, Ml917. Clean metal parts with carbon removing compound.’ The same compound can be used to clean plastic com-

c. Repair. Replace bayonet, M1917, Sling, Ml, Scabbard, Bayonet, Ml917 or cleaning rod (wooden) if unserviceable.

y.J

-./STEP I. REMOVE SLING FROM SWIVEL ON BAYONET BAND ASSEMBLY.

_J

STEP 2. REMOVE SLING FROM STOCK SWIVEL ASSEMBLY. TO INSTALL: REVERSE PROCEDURE. WE 60075

Figure 6-2. Remove/install sling.

(1) Bayonet M1917. Remove grease, oil, and dirt with carbon removing compound (PC-111). Lubricate with general purpose lubricating oil (PL special).

35