Lpile 6 Manual, Version 1 1c1z3r

’s Manual for LPile, Version 6 A Program for the Analysis of Deep Foundations Under Lateral Loading

by

Shin-Tower Wang, Ph.D., P.E. William M. Isenhower, Ph.D., P.E.

2010

Copyright © 2010 by Ensoft, Inc. All rights reserved. This book or any part thereof may not be reproduced in any form without the written permission of Ensoft, Inc.

Date of Last Revision: August 23, 2010

Program License Agreement

IMPORTANT NOTICE: Please read the of the following license agreement carefully. You signify full acceptance of this Agreement by using the software product. Single- versions of this software product is licensed only to the (company office or individual) whose name is ed with Ensoft, Inc., or to s at the ed company office location, on only one computer at a time. Additional installations of the software product may be made by the , as long as the number of installations in use is equal to the total number of purchased and ed licenses. s of network-licensed versions of this software product are entitled to install on all computers on the network at their ed office locations. However, this software can be used simultaneously by as many s as the total number of purchased and ed licenses. The is not entitled to copy this software product unless for backup purposes. The license for this software may not load, rent, lease, or transfer this software package to any other person, company, or office location. This software product and documentation are copyrighted materials and should be treated like any other copyrighted material (e.g. a book, motion picture recording, or musical recording). This software is protected by United States Copyright Law and International Copyright Treaty. Copyright © 1987, 1997, 2004, 2010 by Ensoft, Inc. All rights reserved. Printed in the United States of America. Except as permitted under United States Copyright Act of 1976, no part of this publication may be reproduced, translated, or distributed without the prior consent of Ensoft, Inc. Although this software product has been used with apparent success in many analyses, new information is developed continuously and new or updated versions of the software product may be written from time to time. All s are requested to inform Ensoft, Inc. immediately of any possible errors that are found in the software product. As modifications, updates, or new versions are produced, notices will be sent to all subscribed s that keep their current address on file with Ensoft, Inc. No warrantee, expressed or implied, is offered as to the accuracy of results from software products from Ensoft, Inc. The software products should not be used for design unless caution is exercised in interpreting the results and independent calculations are available to the general correctness of the results. s are assumed to be knowledgeable of the information in the program documentation (’s Manual and Technical Manual) that are distributed with the digital media. s are assumed to recognize that input parameters, e.g. soil parameters, structural properties, program control parameters, and many others, can have significant effect

on the computed solution and must be chosen carefully, s should have a thorough understanding of the relevant engineering principles and relevant theoretical criteria (appropriate references are contained in the software documentation).

iv

Table of Contents

Chapter 1 Introduction .................................................................................................................... 1 1-1 General Description .............................................................................................................. 1 1-2 Program History.................................................................................................................... 1 1-2-1 LPile 1.0 (1986) ............................................................................................................. 1 1-2-2 LPile 2.0 (1987) ............................................................................................................. 2 1-2-3 LPile 3.0 (1989) ............................................................................................................. 2 1-2-4 LPile 4.0 (DOS Version, 1993) ..................................................................................... 2 1-2-5 LPile Plus 1.0 (DOS Version, 1993).............................................................................. 2 1-2-6 LPile 4.0 (Windows Version, 1995) .............................................................................. 3 1-2-7 LPile Plus 2.0 (Windows Version, 1995) ...................................................................... 3 1-2-8 LPile Plus 3.0 (Windows Version, 1997) ...................................................................... 3 1-2-9 LPile Plus 3.0M (Soil Movement Version, 1998) ......................................................... 4 1-2-10 LPile Plus 4.0/4.0M (2000).......................................................................................... 4 1-2-11 LPile 5.0 (2004) ........................................................................................................... 4 1-2-12 LPile 6 (2010) .............................................................................................................. 5 1-3 Technical ................................................................................................................. 5 1-3-1 Technical by Telephone ................................................................................... 6 1-3-2 Upgrade Notifications and Internet Site ........................................................................ 6 1-3-3 Software Customization................................................................................................. 6 1-3-4 Changes of Policy ............................................................................................ 6 Chapter 2 Installation and Getting Started...................................................................................... 7 2-1 Installation and Computing Hardware Requirements........................................................... 7 2-1-1 Single Version ....................................................................................................... 8 2-1-2 Network Version............................................................................................................ 8 2-1-3 Software Updates........................................................................................................... 9 2-1-4 Installation of Software Updates.................................................................................... 9 2-2 Getting Started ...................................................................................................................... 9 2-2-1 File Pull-down Menu ................................................................................................... 10 2-2-2 Data Pull-down Menu.................................................................................................. 11

v

2-2-3 Computation Pull-down Menu..................................................................................... 11 2-2-4 Graphics Pull-down Menu ........................................................................................... 13 2-2-5 Window Pull-down Menu............................................................................................ 13 2-2-6 Help Pull-down Menu.................................................................................................. 13 Chapter 3 Input of Data................................................................................................................. 14 3-1 Data Pull-down Menu ......................................................................................................... 15 3-2 Project Information Dialog ................................................................................................. 15 3-3 Program Options Dialog ..................................................................................................... 15 3-3-1 Computational Options ................................................................................................ 16 3-3-2 Units of Input Data and Computations ........................................................................ 17 3-3-3 Analysis Control Options............................................................................................. 17 3-3-4 Output Options............................................................................................................. 18 3-3-5 Loading Type and Number of Cycles of Loading ....................................................... 18 3-3-6 Text Viewer Options.................................................................................................... 18 3-3-7 Interaction Diagram for Nonlinear Bending Sections ................................................. 18 3-4 Structural Dimensions and Material Properties .................................................................. 19 3-5 Pile Batter and Ground Slope ............................................................................................. 22 3-6 Soil Layering and p-y Curve Models .................................................................................. 23 3-7 Shear-Resistance Curve at Pile Tip..................................................................................... 27 3-8 p-y Modification Factors..................................................................................................... 28 3-9 Output Depths of p-y Curves .............................................................................................. 28 3-10 Axial Thrust Loads for Interaction Diagram .................................................................... 29 3-11 Traditional Loading Analysis ........................................................................................... 29 3-11-1 Pile Head Loading and Options ................................................................................. 29 3-11-2 Distributed Lateral Loading....................................................................................... 31 3-11-3 Lateral Soil Movements............................................................................................. 32 3-12 Load and Resistance Factor Design .................................................................................. 32 3-12-1 Unfactored Loads....................................................................................................... 32 3-12-2 Load and Resistance Factors...................................................................................... 33 3-12-3 Summary of Factored Load Cases ............................................................................. 34 Chapter 4 Graphics ....................................................................................................................... 35 4-1 Introduction......................................................................................................................... 35 4-2 Graphics Mouse Commands ............................................................................................... 35 vi

4-3 Types of Graphics ............................................................................................................... 35 4-4 Fast Graphics ...................................................................................................................... 35 4-4-1 View Pile-Soil Geometry............................................................................................. 35 4-4-2 p-y Curves .................................................................................................................... 35 4-4-3 Deflection vs. Depth .................................................................................................... 36 4-4-4 Moment vs. Depth........................................................................................................ 36 4-4-5 Shear vs. Depth ............................................................................................................ 36 4-4-6 Soil Reaction vs. Depth ............................................................................................... 36 4-4-7 Load vs. Top Deflection .............................................................................................. 36 4-4-8 Load vs. Max Moment................................................................................................. 36 4-4-9 Pile Length vs. Top Deflection .................................................................................... 36 4-4-10 EI vs. Moment............................................................................................................ 37 4-4-11 Moment vs. Curvature ............................................................................................... 37 4-4-12 Interaction Diagram ................................................................................................... 37 4-4-13 K22 vs. Lateral Load ................................................................................................... 37 4-4-14 K23 vs. Lateral Load ................................................................................................... 37 4-4-15 K32 vs. Moment .......................................................................................................... 37 4-4-16 K33 vs. Moment .......................................................................................................... 38 4-4-17 K22 vs. Pile Top Deflection ........................................................................................ 38 4-4-18 K23 vs. Pile Top Deflection ........................................................................................ 38 4-4-19 K32 vs. Pile Top Rotation ........................................................................................... 38 4-4-20 K33 vs. Pile Top Rotation ........................................................................................... 38 4-5 Presentation Graphs ............................................................................................................ 38 Chapter 5 Example Problems........................................................................................................ 39 5-1 Introduction......................................................................................................................... 39 5-2 Example Problem 1............................................................................................................. 41 5-2-1 Loading and Boundary Conditions .............................................................................. 41 5-2-2 Pile Details................................................................................................................... 42 5-2-3 Selection of Form of p-y Curves.................................................................................. 43 5-2-4 Results of Computations with p-y Curves ................................................................... 43 5-2-5 Input and Output Files ................................................................................................. 47 5-3 Example Problem 2............................................................................................................. 47 5-3-1 Loading and Boundary Conditions .............................................................................. 48 vii

5-3-2 Pile Details................................................................................................................... 48 5-3-3 Selection of Form of p-y Curves.................................................................................. 49 5-3-4 Results of Computations with p-y Curves ................................................................... 50 5-3-5 Input Data - Initial Run................................................................................................ 51 5-3-6 Input Data - Final Run ................................................................................................. 51 5-3-7 Output Data - Final Run............................................................................................... 51 5-4 Example Problem 3............................................................................................................. 51 5-4-1 Loading and Boundary Conditions .............................................................................. 52 5-4-2 Pile Details................................................................................................................... 54 5-4-3 Selection of Form of p-y Curves.................................................................................. 55 5-4-4 Results of Computations with p-y Curves ................................................................... 55 5-4-5 Input Data .................................................................................................................... 57 5-4-6 Output .......................................................................................................................... 57 5-5 Example Problem 4 Buckling of a Pile-Column................................................................. 57 5-6 Example Problem 5............................................................................................................. 59 5-6-1 Input Data .................................................................................................................... 61 5-6-2 Output Data.................................................................................................................. 61 5-7 Example Problem 6............................................................................................................. 61 5-7-1 Input Data .................................................................................................................... 63 5-7-2 Output Data.................................................................................................................. 63 5-8 Example Problem 7............................................................................................................. 63 5-8-1 Input Data .................................................................................................................... 64 5-8-2 Output Data.................................................................................................................. 64 5-9 Example Problem 8............................................................................................................. 64 5-9-1 Input Data .................................................................................................................... 67 5-9-2 Output Data.................................................................................................................. 67 5-10 Example Problem 9........................................................................................................... 67 5-10-1 Input Data .................................................................................................................. 69 5-10-2 Output Data................................................................................................................ 69 Chapter 6 Validation ..................................................................................................................... 70 6-1 Introduction......................................................................................................................... 70 6-2 Case Studies ........................................................................................................................ 70 6-3 Verification of Accuracy of Solution.................................................................................. 71 viii

6-3-1 Solution of Example Problems .................................................................................... 71 6-3-2 Check of Echo Print of Input Data............................................................................... 72 6-3-3 Investigation of Length of Word Employed in Internal Computations ....................... 72 6-3-4 Selection of Tolerance and Length of Increment......................................................... 72 6-3-5 Check of Soil Resistance ............................................................................................. 74 6-3-6 Check of Mechanics..................................................................................................... 74 6-3-7 Use of Non-Dimensional Curves................................................................................. 76 6-3-8 Concluding Comments on Verification ....................................................................... 76 6-3-9 Input Data for Verification Problem............................................................................ 77 6-3-10 Output Data for Verification Problem ....................................................................... 77 Chapter 7 Line-by-Line Guide for Input....................................................................................... 78 7-1 Key Words for Input Data File ........................................................................................... 78 7-1-1 TITLE Command......................................................................................................... 78 7-1-2 OPTIONS Command................................................................................................... 79 7-1-3 SECTIONS Command................................................................................................. 80 7-1-4 AXIAL THRUST LOADS Command ........................................................................ 80 7-1-5 SOIL LAYERS Command .......................................................................................... 87 7-1-6 TIP SHEAR Command................................................................................................ 87 7-1-7 PILE BATTER AND SLOPE Command.................................................................... 87 7-1-8 LRFD LOADS Command ........................................................................................... 87 7-1-9 LRFD FACTORS AND CASES Command ............................................................... 87 7-1-10 LOADING Command................................................................................................ 87 7-1-11 SOIL MOVEMENTS Command............................................................................... 87 7-1-12 GROUP EFFECT FACTORS Command.................................................................. 87 7-1-13 P-Y OUTPUT DEPTHS Command .......................................................................... 87 7-2 LRFD Data File................................................................................................................... 87

ix

Chapter 1 Introduction 1-1 General Description LPile is a special purpose program that can analyze a pile or drilled shaft under lateral loading. The program computes deflection, shear, bending moment, and soil response with respect to depth in nonlinear soils. The program has graphic capabilities for presenting the results and includes a interface for data entry. The pile is modeled The soil and rock is modeled using lateral load-transfer curves (p-y curves) based on published recommendations for various types of soils and rocks. The p-y curves are internally generated by the program. Alternatively, the can manually input p-y curves for a soil layer. The program also contains specialized procedures for computing p-y curves for layered soils. Several types of pile-head boundary conditions may be selected, and the properties of the pile may be input as a function of pile length. Additionally, LPile can compute the nominalmoment capacity and provide design information for rebar arrangement. The may also ask the program to take into cracked/uncracked flexural stiffnesses while computing the response of a pile.

1-2 Program History 1-2-1 LPile 1.0 (1986) When the IBM XT® personal computer was introduced in 1984, Dr. Lymon C. Reese, the founder of Ensoft, Inc., foresaw future improvements in analysis and design of pile foundations through the use of improved software. The development of LPile 1.0 for its first commercial distribution was begun in 1985 and was completed in 1986. Although the general theory and methodology of LPile 1.0 was similar to COM624, which operated primarily on mainframe computers, LPile was completely rewritten with a new solver and new interactiveinput method. LPile was developed for analyzing single piles and drilled shafts under lateral loading. LPile was compiled by the IBM Fortran compiler on the IBM XT personal computer. LPile 1.0 had the following features: •

The program could generate p-y curves internally for soft clay, stiff clay with free water, stiff clay without free water, and sand. The program also allowed s to input defined p-y curves for a selected layers.

•

Modifications of the p-y curves for layered soils were introduced in the program based on the recommendations of Georgiadis (1983).

•

A total of four boundary conditions and loading types were available for the pile head. Distributed loading could also be specified at any pile depth.

•

An interactive input was provided for the to prepare the input data step-by-step.

1

Chapter 1 – Introduction •

An option was introduced for considering tip-resistance curves.

1-2-2 LPile 2.0 (1987) With the introduction of new graphics hardware for personal computers such as EGA color monitors and an improved central processor on IBM® AT computers, the need for graphic display of computed pile deflection, bending moment, shear, and soil resistance became desirable for engineering software. The second version of LPile was introduced in 1987 with a separate graphics module. Improvements were also made on the main program and input editor. 1-2-3 LPile 3.0 (1989) With the wide acceptance of LPile by government agencies, universities, and engineering firms during the first three years, improvements in -friendliness were considered essential. LPile 3.0 was introduced in 1989 with an input preprocessor featuring pull-down menu, spreadsheet cells, and on-screen help commands. High-resolution graphics for CGA, EGA, and VGA displays were also added to the output post-processor. The main program also added the following technical features: •

New p-y criteria for vuggy limestone/rock.

•

Options for modifying internally-generated p-y curves in special conditions.

•

The pile head was allowed to be positioned either above or below the ground surface.

1-2-4 LPile 4.0 (DOS Version, 1993) LPile 4.0 was released in 1993, about 4 years after the previous upgrade. Features incorporated into the new version were: •

New p-y criteria for soils whose strength is represented using both cohesion and friction angle.

•

New p-y criteria for sand based on the recommendations of the American Petroleum Institute’s API-RP2A (1987).

•

New procedures for including the effect of sloping ground on p-y curves.

•

New graphic plots for representing load versus deflection at the pile head and load versus maximum bending moment.

1-2-5 LPile Plus 1.0 (DOS Version, 1993) New technology for pile foundations required the incorporation of nonlinear properties for the pile’s flexural rigidity during analysis of their lateral deflections. A separate computer program named STIFF was developed in 1987 to provide the with information about the relationship of applied moment versus flexural rigidity of a structural element, and to compute the ultimate bending capacity from a specified structural section. LPile Plus was thus developed in 1993 by combining LPile 4.0 and STIFF. With the functionality obtained from STIFF, LPile Plus had the capability to take into the flexural rigidity of uncracked and cracked sections individually, which led to a more reasonable solution for the flexibility of a pile under lateral loading.

2

Chapter 1 – Introduction 1-2-6 LPile 4.0 (Windows Version, 1995) The success of Windows 3.1 from Microsoft, Inc. as the new platform for personal computers pushed software development into a new era with strong demand for -friendly features. LPile 4.0 for Windows was released in 1994 with input preprocessor and output postprocessor written specifically for the Windows 3.1 platforms. 1-2-7 LPile Plus 2.0 (Windows Version, 1995) The initial windows version for LPile Plus was released in 1995. The preprocessor program used a mouse with pull-down menu, dialog boxes, grid cells, and push buttons to improve the process of data entry. The graphics program, also running within the Windows platform, ed any printer device recognized by the Windows environment. The main program added an option for s to specify the rebar area at each location externally. 1-2-8 LPile Plus 3.0 (Windows Version, 1997) With the 32-bit operating systems provided by Microsoft Windows 95 and Windows NT, software developers were provided with tools to develop interfaces with advanced, highresolution graphics. LPile Plus 3.0 was developed based on the technological advances for new interfaces. The significant features of this upgrade can be summarized as follows: •

A new soil criterion for weak rock was added to the previously-existing eight soil types. The p-y criterion for weak rock is primarily applicable to the weathered sandstone, claystone, and limestone with uniaxial compressive strengths of less than 1000 psi.

•

Computations are available for pile responses at various pile lengths. The is provided with a plot of pile length versus pile-head deflection that is helpful for determining the critical pile penetration.

•

An option is now provided to compute values for a foundation stiffness matrix which may be used in structural analysis models for a certain range of loads. Under this new option, the program creates curves of incremental loading versus foundation stiffness components K22, K23, K32, and K33, as shown in Figure 1.1.

•

Improved file-management features are also included to help the during program execution. The may now use menu items for data entry, computation, output review, and graphics display under the same application window.

•

The may select to input data in English units or SI units for convenience. The SI units are enforced in many publications and documents. The program is able to convert between units internally.

•

All grid cells for data entry were developed with functions that understand mathematics formulas. The is allowed to input such formulas as PI*36^2/4.0 for the crosssectional area of a circular pile with 36 units of outside diameter.

•

The graphical observation of output curves features a new interface that allows several levels of zooming in areas of particular interest. The may thus observe detailed behavioral measurements of any portion of the modeled pile.

3

Chapter 1 – Introduction 1-2-9 LPile Plus 3.0M (Soil Movement Version, 1998) A special version for LPile Plus 3.0 was released in 1998 called version 3.0M. The LPile Plus 3.0M software is the standard LPile Plus 3.0 version with the addition of the following two additional capabilities: •

The is able to input a profile of soil movements versus depth as additional loading on the pile. The soil movements of the soil may be produced from any action that causes soil movements, such as movements due to slope instability, lateral spreading during earthquakes, and seepage forces. The 3M module incorporates an alternative solution to the governing differential equation to for the lateral movement of the soils.

•

The can input nonlinear curves of flexural stiffness versus bending moments for different pile sections. This feature is useful for cases where the pile has different structural properties along its depth.

1-2-10 LPile Plus 4.0/4.0M (2000) LPile 4.0/4.0M was developed for compatibility with Windows NT, 95, 98, and 2000. Modules used for computations were compiled as DLL (dynamic link library) functions, which significantly increased performance. The new features for this upgrade can be summarized as follows: •

The program has the capability to generate and take into nonlinear values of flexural stiffness (EI). These values are generated internally by the program based on cracked/uncracked concrete behavior and -specified pile dimensions, and material properties for reinforced concrete sections. The program adds a new option for analyzing prestressed concrete sections in Version 4.0.

•

The can specify both deflection and rotation at the pile as a new set of boundary conditions in Version 4.0.

•

LPile Plus 4.0 can perform push-over analyses and analyze the pile behavior after a plastic hinge (yielding) develops.

•

Soil-layer data structures and input screens are improved in Version 4 to help the enter data conveniently with default values provided. More than 100 error-checking messages are added into Version 4.0

•

Files opened recently will be listed under File menu. New options for graphics title, legends and plot of rebar arrangement are incorporated into Version 4.0.

•

New data and formats are added to the output file in Version 4.0

1-2-11 LPile 5.0 (2004) LPile Version 5.0 was developed to meet needs for more versatility. Two more p-y criteria were added into the program. The option of specifying soil movement became a standard feature in the program. The can use a presentation graphics utility to prepare various engineering plots in high quality for presentations and reports. The new features for this version can be summarized as follows:

4


Version 5 allows the to define multiple sections with nonlinear bending properties. This feature permits the designer to place reinforcing steel on sections of a drilled shaft as needed, depending on the computed values of bending moment and shear.

•

Version 5 allows the to enter externally computed moment vs. EI curves for multiple sections.

•

Version 5 can analyze the behavior of piles subjected to free-field soil movement in lateral direction. Free field displacements are soil motions that may be induced by earthquake, nearby excavations, or induced by unstable soils.

•

The p-y criteria for liquefiable sand developed by Rollins, et al. (2003), and p-y criteria for stiff clay with -specified initial k values, recommended by Brown (2002), were added into Version 5.0.

•

The types and number of graphs generated by Version 5 have increased over previous versions. More importantly, the graphs may now be edited and modified by the in an almost unlimited number of ways.

•

Many hints and notes were added into input windows to assist the in selecting proper data for each entry.

1-2-12 LPile 6 (2010) •

Version 6 has the capability of performing analyses for Load and Resistance Factor Design. Up to 100 load case combinations may be defined and up to 100 unfactored loads may be defined. Load case combinations are defined by entering the load factors for each load type and the resistance factors for both flexure and shear. Optionally, the may enter the load case combinations by reading an external plain-text file.

•

Improvements on the computation of flexural rigidity (EI) of drilled shafts allow the program to converge even plastic hinges were developed in the push-over analyses.

•

The can specify either US customary units (pounds, inches, feet) or SI units (kilonewtons and meters) for inputting and displaying data. Most commonly-used customary units such as lbs/ft2(for shear strength) and lbs/ft3 (for unit weight) are used in Version 6.0.

•

A total of 12 p-y criteria for different types of soil and rock were included into Version 6.0.

•

The Input dialogs for definition of soil properties have been improved to aid the . Default values for some input properties are provided. Hints and notes are also shown on input dialogs to assist the for data entry.

•

Over 175 error and warning messages have been provided, making it easy for occasional s to run the program and to solve run-time errors.

1-3 Technical Although LPile 6 was programmed for ease of use, some s may still have questions. The Ensoft technical staff strongly encourages s to utilize electronic means of via email. In any request, please include the following information: 5


Software version (obtained from the Help/About menu)

•

Description of the problem

•

Attach a copy of input-data file (file extension .lp6d)

•

Name and telephone number of the person and of the ed (or name and office location of the ed company)

Although immediate answers are offered on most technical requests, please allow up to two business days for a response in case of difficulties or schedule conflicts. 1-3-1 Technical by Telephone Technical help by means of direct calls to our local telephone number, (512) 244-6464, is available, but limited. The current policy of Ensoft is that all telephone calls for software will be answered free of charge for each call if the has a valid maintenance contract. The maintenance is free of charge within the first year of the software purchase. A maintenance fee will be required after the first year of purchase. Annual maintenance policy and the invoice will be sent to the in advance before the maintenance contract expired. Request of software by email is most welcomed because the staff can review your email and input/output files for solving the problems efficiently. 1-3-2 Upgrade Notifications and Internet Site Subscriptions for software updates are available for a fee ( Ensoft for latest pricing). All s who are subscribed to the software update compact disk service and keep their address current on file at Ensoft will receive update compact disks by mail quarterly when new versions become available. All s with current maintenance subscriptions may also obtain updates from our website (http://www.ensoftinc.com), plus additional information on software updates, demos, and new applications; technical news, and company information. 1-3-3 Software Customization Customized versions of the LPile may also be obtained under contractual agreement for the costs of additional programming. Ensoft to discuss what options are available. 1-3-4 Changes of Policy The software policy and associated expenses are subject to change without notice, as many of the costs associated with technical are outside of Ensoft’s direct control. However, any change of policy will be provided during telephone calls for software .

6

Chapter 2 Installation and Getting Started 2-1 Installation and Computing Hardware Requirements LPile 6 is distributed with a black USB security device. This method of distribution is compatible with Windows operating systems from Windows 95 through Windows Seven, has better capabilities over other alternatives, and allows s to obtain software updates or replacements via the Internet. Before installing, your personal computer should be equipped with the following: •

An open USB port

•

At least 50MB of free space on the hard disk drive

•

At least 2 GB of random access memory (RAM)

•

At least 128 MB of video memory

•

A monitor with a display resolution of 1,280 by 1028 pixels or greater

•

Windows 2000, Windows XP, Windows Vista, or Windows 7 operating systems with latest service packs installed To install the software:

1. Insert the black USB key into any USB port. 2. Insert the compact disk from Ensoft. If Autoplay is enabled, Windows will ask you if you want to run Setup.exe. If Autoplay is not enabled then from My Computer double click the drive into which the installation compact disk is inserted. 3. Select to install LPile, and then select on the radio button for “Single- License” if installing a single- version of the software or select “Network License” if installing a network version of the software. Note: if the wrong version for the license is selected and program installation is completed, it will be necessary to completely uninstall the software prior to re-installation for the correct license version

7

Chapter 2 – Installation and Getting Started

2-1-1 Single Version If your license is for a single-, select that option and click next. Follow the directions in the dialog boxes until the installation is completed. 2-1-2 Network Version At the following window, choose the appropriate option for either “Client Computer” or “Software Server.” Note that the “Server” version should be installed by the network while logged in with full istrative privileges enabled and must be installed only on one server computer. The USB security device must be plugged in to the software server after the software installation is completed, and the Server computer must be logged onto the network in order for “Client” s to access LPile.

8

Follow the on-screen instructions until installation is complete. 2-1-3 Software Updates Ensoft will maintain the software, produce software improvements and/or fixes and place the latest software programs on Ensoft’s website. s with current maintenance contracts may the latest program update for free from the following URL: http://www.ensoftinc.com. 2-1-4 Installation of Software Updates 1. the appropriate file specified above to a local directory. If the was not made to the computer with the hardware lock, the ed file must be copied to the appropriate computer. 2. Navigate to the directory the installation file is located in and then double click to execute the installation. Follow the on-screen instructions until installation is complete.

2-2 Getting Started A general diagram showing the menu choices and operation flowchart of the program is presented in Figure 2-4. The following paragraphs provide a description of the program function and will guide the in using the program.

9

Chapter 2 – Installation and Getting Started

Start LPile

File Menu Open or save an existing data file

Data Menu Input or edit data or program options

Help Menu Help available for most commands

Computation Menu Perform analysis and view output report

Graphics Menu Generate and view output graphics

Figure 2-4 Operational Flowchart for LPile Start the program by navigating to the shortcut in the start menu and clicking on it. The main program window will appear. You should see a blank window with a toolbar at the top with the following choices: File, Data, Computation, Graphics, Window, and Help. As a standard Windows feature, pressing Alt displays the menu operations with underlined letters. Pressing the underlined letter after pressing Alt is the same as clicking the operation. For example, to open a New File, the could press Alt, F, N, in sequence, Ctrl+N, or click File then New. Additionally, holding the mouse cursor over an icon displays the icon function. 2-2-1 File Pull-down Menu The File pull-down menu is used to control basic file operations for input data files. Most of these program function are also available from the programs speed bar by pressing the indicated speed button.

10

A list of recently opened files is displayed in between Save As… and Exit. •

New: Create a new data file.

•

Open…: Open an existing data file. If a partially-completed LPile input file, or an invalid data file is opened, an information window reporting that an “invalid or incomplete” file is being opened. Clicking OK dismisses the message, and the previously saved data should be available. If a complete input file is loaded, an information window reporting that “Data File: (name of file), has been read by LPile” should appear, and the should click OK.

•

Save: Save input data under the current file name.

•

Save As…: Save input data under a different file name.

•

Exit: Exit the program. If the input file was modified but unsaved, a prompt will appear asking if the would like to save changes.

2-2-2 Data Pull-down Menu Please refer to Chapter 3 for a detailed discussion of this menu. 2-2-3 Computation Pull-down Menu

2-2-3-1 Run Analysis: This option runs the analytical computations. Analyses can be performed successfully only after all data has been entered and saved. An existing input file will automatically be resaved to disk upon running analysis. To indicate to the that an analysis is in progress, LPile changes the cursor to an hourglass and displays a message of “Please wait while computations are in progress” during the execution. A message box showing “The analysis was completed without errors.” Is shown after the execution is successful. If there are input or runtime errors

11

Chapter 2 – Installation and Getting Started during execution, appropriate error messages will appear in the dialogue box. In addition, nonfatal warning messages for unusual situations warranting the attention of the are also shown. In most cases, the program will display information that explains the causes of error and suggest corrective actions. If no explanations are given, the may send the input file to Ensoft via email for a detailed diagnosis. The following text files are produced: File Extension *.lp6d *.lp6o *.lp6r *.lp6t

Description Input file Output report file Processor run notes file Graphics titles file

These files will be created in the same directory as the input file.

2-2-3-2 View Input Text: This menu option activates the -specified text editor to display the analytical input data in plain-text format. This option is available after the input data has been saved to disk, or when opening an existing input-data file. It is useful for experienced s who may just want to change quickly one or two parameters using the text editor, or for s wishing to observe the prepared input data in text mode. 2-2-3-3 View Processor Run Notes: The program begins each analysis by first saving the current data to disk, then starting the analysis routine that reads the input data from the saved disk file. If an error is detected, the program will display a message dialog that informs the about the type of error and will in many cases suggest a solution for the error. Input errors may consist of missing data, erroneous data, or inconsistent data. Usually, the content of the error message dialog is copied to the processor run notes file. If the processor-run notes stop without listing the line “The Execution is in progress…,” the should check the input corresponding to the last line read and the line that immediately follows (that was not read). In some cases, the processor-run notes will also include an error message. 2-2-3-4 View Output Report: This option has the text editor open the analytical-output data. The option becomes available only after a successful run has been made. Certain output files may be too large for Microsoft Notepad to handle, so other text editors (Microsoft WordPad, for example) would need to be used. Output files usually contain the following information: 1. Authorized -license information 2. If selected, the output will contain a section related to computations of ultimate bending moment and variations of flexural stiffness with applied moment, including an echo-print of the input data as well as result tables. 12

3. Echo-print of input data for pile analysis. s are strongly recommended to check the echoprint of their input data for mistakes. 4. If selected, data for selected p-y curves printed for verification. 5. Data for deflection, bending moment, shear, soil resistance, and related information, as a function of depth for the modeled pile. 6. Output verification of the finite-difference approximations, providing data about the maximum moment and lateral force imbalances observed during execution (maximum imbalances should usually consist of small numbers). 7. Output summary table, containing information about the results and number of iterations performed until convergence was reached. 8. If selected, summary table of pile-head deflection versus pile length. 9. If selected, summary table of data generated for foundation stiffness. 2-2-4 Graphics Pull-down Menu Please refer Chapter 4 for a detailed discussion of this menu. 2-2-5 Window Pull-down Menu Cascade: This option organizes all open windows so that they are all visible. See above for an example. 2-2-6 Help Pull-down Menu

2-2-6-1 Contents: The main reference files for help are accessed through this option. 2-2-6-2 Update: Opens the LPile update page in the ’s default browser. 2-2-6-3 About: This option provides a screen describing the program version, date, and methods for accessing technical .

13

Chapter 3 Input of Data The input of specific parameters for an application is controlled under options contained within the Data menu. It is recommended that the choose each menu and enter parameters in a consecutive manner, starting from the top option. Windows may optionally be left open on the screen. The selection of other menu options will then produce new windows on top of those that were left open. Many of the menus will have Add Row and Delete Row buttons. The former always adds a new row to the end of all existing rows, and the latter deletes the row where the cursor is currently located. All cells that require numeric data may accept mathematical expressions as entries. In general, one may enter numerical expressions in the same manner as most spreadsheet programs allow, but one must omit the leading equal sign. Entering a mathematical expression works similarly to entering normal numeric data; the simply types the expression then presses the “Enter” key. The following table shows a list of ed operations and constants, with the order of operations following the order listed. Implicit multiplications using constants is not ed (use 2*pi instead of 2pi). Negation of the constants pi or e is not allowed. For instance, instead of entering PI the must enter −(pi). Scientific notation is inferred if e or E is immediately following by a number (i.e. 29e6 or 0.5e-5), for input of very large or very small numbers. After an expression is calculated, the numbers will be displayed using standard notation. Mathematical Operators (listed in precedence) Symbol Description () Parenthesis (may be nested) ^ Exponentiation * Multiplication / Division + Addition – Subtraction/Negation Mathematical Constants Symbol Value 3.141592654… π (PI or pi) e (or E) 2.718281828…

14

Chapter 3 – Input of Data

3-1 Data Pull-down Menu

3-2 Project Information Dialog

3-3 Program Options Dialog All program options have been consolidated into a single input dialog box. The program options are used by the to select features of each set of data being analyzed by LPile Plus. This input dialog provides options that are grouped into Computational 15

Chapter 3 – Input of Data Options, Engineering Units Options, Analysis-Control Options, Output options, Loading Options, and Text Viewer Options. Some default settings are provided if the does not have any desire to make a change. The should to click the OK button in order to save the accepted selections; otherwise, the selections will not be stored when the screen is closed.

3-3-1 Computational Options •

Use Load and Resistance Factors: If left checked, LPile permits inputs of load cases defined for various pile-head boundary conditions. If checked, LPile can perform Load and Resistance Factor Design (LRFD) computations. In this mode, the may enter up to 100 unfactored loads of various types. All loads are assumed to be for shear and moment pile-head loading conditions. The program will then add all loads of the same load type to obtain the total unfactored load for the load type in question. The LRFD case load combinations may be either read from an external file (with the file type of lrfd) or may be entered by the .

•

Compute Pile-Head Stiffness Matrix Components: :If a check mark is placed on this option, the program automatically selects up to ten additional lateral loads and moments based on the initial values specified by the . Multiple analytical runs are automatically produced to determine the nonlinear variation of foundation stiffness. The program selects the additional loads based on the initial values specified by the in the Boundary Conditions and Loading window screen under the Data menu. This option can only be used if the selects to input Shear [F] and Moment [F-L] as boundary conditions. The program automatically reduces the -specified values of lateral load and moment in ten decrements to zero. Computations are performed for all twenty runs to 16

Chapter 3 – Input of Data form the curves of foundation stiffness for a range of loading. Higher values of lateral load and/or moment should be inputted by the if curves of foundation stiffness for a wider range of loading are desired. In the output file and graphics, the is provided with plots of four values of a matrix that can be used to represent the foundation stiffness in the superstructure analysis for a certain range of loading. The axial component of the foundation-stiffness matrix must be calculated separately perhaps with the help of computer programs designed to find the axial capacity and short-term settlements of drilled shafts or driven piles. s are strongly recommended not to select this option on initial runs until being assured to have a working analytical model. This option considerably increases computation time. In the output file and graphics, the is provided with plots of four values of a matrix that can be used to represent the foundation stiffness in the superstructure analysis for a certain range of loading. The axial component of the foundation-stiffness matrix must be calculated separately perhaps with the help of computer programs designed to find the axial capacity and short-term settlements of drilled shafts or driven piles. •

Include Shearing Resistance at Pile Tip: Activates Shear Resistance Curve at Pile-Tip under the Data menu.

•

Include Loading by Lateral Soil Movements: Activates Lateral Soil Movements under the Data menu.

•

Include Modification Factors for Group Action: Activates p-y Modification Factors for Group Action under the Data menu.

•

Computer Nonlinear Bending Stiffness Only: If checked, LPile will only compute the nonlinear moment-curvature relationships for the non-elastic pile sections entered. If unchecked, the program will compute nonlinear moment-curvature relationships for all non-elastic sections and perform computations of pile response under lateral loading using the nonlinear moment-curvature relationships.

3-3-2 Units of Input Data and Computations Here the can specify either US customary units (pounds, inches, feet) or SI units (kilonewtons and meters) for inputting and displaying data. 3-3-3 Analysis Control Options The Analysis Control Options are used to specify the maximum number of iterations, the convergence tolerance on deflections, the limit on excessive deflection of the pile head, and the number of pile increments. The maximum number of iterations performed by the program for the pile solution can be set by the . Many problems will converge in under 100 iterations unless a plastic hinge is being developed in an analysis using nonlinear EI. If a push-over analysis is being performed using the displacement and moment pile-head boundary condition, the iterations limit should be set to the maximum value of 1000 to allow for plastic hinges to develop in the pile.

17

Chapter 3 – Input of Data Recommended Lower Limit Upper Limit:

100 to 300 10 1,000

The Excessive Deflection Value is used to end analyses in which iterative solution is diverging without limit. The should enter a value of deflection for the pile head that is grossly excessive to stop the analysis. The recommended value is 10 times the pile diameter. The Excessive Deflection Value is used to end analyses in which iterative solution is diverging without limit. The should enter a value of deflection for the pile head that is grossly excessive to stop the analysis. The recommended value is 10 times the pile diameter. 3-3-4 Output Options •

Generate p-y Curves at -Specified Depths: Activates the Output Depths of p-y Curves option under the Data menu.

•

Print Summary Tables Only: This option allows the to specify the number of finitedifference nodes where results will be printed in the table of output. As a default, results are printed at every finite increment of pile length. This option is disabled if the has a check mark on the Only Print Summary Tables option under the Options menu. A value of 1 prints the values at every node; 2 prints values at every other nodes, etc.

3-3-5 Loading Type and Number of Cycles of Loading Here the can specify either static or cyclic loading. The type of loading is very important when analyzing piles under lateral forces. Further information on the influence of loading type is included in the Technical Manual. In general, cyclic loading is primarily used for low-frequency, large amplitude storm wave or wind loads. Earthquake and machine vibrations produce dynamic loads and are not considered cyclic in this program. If cyclic loading is selected, the must also specify the number of cycles of loading, ranging from 2 to 5,000 cycles. The effect of cyclic loading is to change how the soil resistance is computed for the p-y curves, as described in the Technical Manual. 3-3-6 Text Viewer Options The should enter the complete path and command line for their preferred text editor or word processor. As a default, the command line c:\windows\notepad.exe sets Microsoft Notepad as the default text editor. An internal text editor can also be selected. The selected text editor will be used for View Input Text File, View Processor Run Notes, View Output Text File, and Text Viewer under the Computation menu. 3-3-7 Interaction Diagram for Nonlinear Bending Sections Checking the Compute Interaction Diagrams box activates the Axial Thrust Loads for Interaction Diagram option in the Data menu. The will need to select the LRFD rules to be applied, as well as the type of transverse reinforcement, as the type of transverse reinforcement may determine the resistance factor to be employed. 18


3-4 Structural Dimensions and Material Properties LPile Plus has the capability to evaluate the nominal moment capacity and nonlinear bending stiffness relationships for deep foundations made from normally-reinforced concrete, pipe sections, and prestressed concrete. These features can determine how the effective bending stiffness will vary as the concrete cracks in tension and the reinforcing steel yields. Use of the features to evaluate ultimate moment capacity and nonlinear bending stiffness is essential when analyzing the behavior of drilled shafts under lateral loading. The should to click "OK" button in order to save the accepted selections; otherwise, the selections will not be stored when the screen is closed.

19


20


21


The selects can input pile shape and material properties in this multi-page dialog. This is done in the following steps: 1

Use the option buttons to select the desired section type and shape.

2

At the top of the window, right under the pull down menu, click on the tab to the right of Section Type. This second tab is for inputting dimensions for the shape selected, e.g. the will be asked to input length, width, and depth for a rectangular concrete pile, or length, diameter, and thickness for a pipe pile.

3-5 Pile Batter and Ground Slope The specifies the ground slope and batter angles using the dialog. The drawing in the dialog realistically illustrates the ground slope and pile batter along with the sign convention for loading. If flat ground slope is selected and the pile is vertical, the angles will be zero. •

Slope Angle: This is the angle, in degrees, formed between a sloped ground surface and the horizontal surface. As indicated in the following figure, the value of the slope angle is 22

Chapter 3 – Input of Data positive if the pile tends to move downhill upon application of the lateral load. The lateral capacity provided by soils in a positive slope is thus reduced. Piles that tend to move uphill in a sloping ground use negative values of slope angle. The lateral capacity provided by soils in a negative slope is thus increased. •

Batter Angle: The sign convention that is used to for battered piles also depends on the direction of the applied lateral load and is shown in the figure.

3-6 Soil Layering and p-y Curve Models

23

Chapter 3 – Input of Data This data table allows the to specify the different types of soil to be used for the automatic generation of lateral load-transfer curves (p-y curves). LPile 6 will automatically generate the selected curves under default conditions. •

Layer: The soil layer number is assigned automatically to each soil layer. This number is automatically provided by the program as new rows of soil layers are added. The maximum number of soil layers that may be entered is limited to 40.

•

p-y Curve Soil Model: There are 13 internal types of soils that can be specified in LPile 6 using the dropdown box: 1. Soft Clay (Matlock) 2. Stiff Clay with Free Water (Reese) 3. Stiff Clay without Free Water (Reese) 4. Modular Stiff Clay without Free Water 5. Sand (Reese) 6. API Sand (O’Neill) 7. Liquefied Sand (Rollins) 8. Weak Rock (Reese) 9. Strong Rock (Vuggy Limestone) 10. Piedmont Residual 11. Silt (cemented c-phi) 12. Loess 13. Elastic Subgrade In addition, s may choose to define their own p-y curves by selecting the last option, Input p-y Curves. Stiff clay with free water, in general, is used to represent soil conditions where stiff clay is the top layer with water existing above the ground line or in any conditions where it is believed that any annular space between the pile and soil may fill with water. A general review of the theory of p-y curves for different types of soils is included in the Technical Manual.

•

Top of Soil Layer Below Pile Head: Values for the top of the soil layer are entered according to the origin of coordinates. The origin of coordinates is always at the pile head, which is the point of application of boundary conditions and corresponding loads. A positive value for the Top Layer entry indicates a distance measured downward from the top of the pile. A negative value indicates a distance measured above the top of the pile (only used for when the pile head is embedded below the ground surface). The value of zero may be used in the first layer if the pile head is at the level of the ground line.

•

Bottom of Soil Layer Below Pile Head: Values for the bottom of the soil layer are also entered according to the origin of coordinates. The coordinate of the bottom of each layer should always be equal to the coordinate of the top of the immediately consecutive layer. 24

Chapter 3 – Input of Data The bottom of the last soil layer must at least reach the same depth as the bottom of the modeled pile •

Soil Properties: The last column contains a context-sensitive button that varies depending on the p-y curve soil type selected. The table button activates a soil type specific data entry dialog where the enters effective unit weight, shear strength parameters, and any other required soil/rock property parameters, depending on the soil type selected. Descriptions follow: o Effective Unit Weight: Values of effective unit weight for each soil depth are entered in units of force per unit volume. The program will linearly interpolate values of unit weight located between the top and bottom depths of the layer. Soil layers should be sub-divided anywhere step changes in values are needed, such as at the depth of the water table. o k Value for Soil Layers: This is the value for k used in the equation Es = k x. This constant is in units of force per cubic length and depends on the type of soil and lateral loading imposed to the pile group. It has two different uses: (i) to define the initial (maximum) value of Es on internally generated p-y curves of stiff clays with free water and/or sands; and (ii) to initialize the Es array for the first iteration of pile analysis. o Undrained Shear Strength: Values of undrained shear strength (cu) for clays and silts at each depth are entered in standard units of force per unit area. The undrained shear strength is not needed for sand layers. The undrained shear strength is generally taken as half of the unconfined compressive strengths. o Internal Friction (degrees): Values of the angle of internal friction φ for sands and/or silts at each soil depth are entered in degrees. o Strain: Values of strain at 50% of the maximum stress ε50 for clays and/or silts at each soil depth are entered in standard units of strain. Strain value is not needed for sand layers. If soil test data are available, the may enter the value based on the stressstrain curves measured in the soil laboratory. The p-y curves for weak rocks need a strain parameter krm which is equivalent to ε50. More information can be found in the Technical Manual. o Elastic Modulus for Weak Rock: The mass modulus for weak rock should be entered for this value. This value may be measured in the field using an appropriate test or may be obtained from the product of the modulus reduction ratio and Young’s modulus measured on intact rock specimens in the laboratory o Uniaxial Compressive Strength: This value is the uniaxial compressive strength of weak rock at the specified depth. Values at elevations between the top and bottom elevations will be determined by linear interpolation. Any input values that are considered unreasonable are flagged in the output file and a warning dialog box is displayed. However, the analysis is performed normally.

25

Chapter 3 – Input of Data o Rock Quality Designation: The secondary structure of the weak rock is described using the Rock Quality Designation (RQD). Enter the value of RQD in percent for the weak rock. o Strain Factor krm: The parameter krm typically ranges between 0.0005 and 0.00005. The input window for weak rock is shown as a sample.

. •

Input p-y Curves

26

Chapter 3 – Input of Data This layer option allows the to enter specific relationships of soil resistance (p) and lateral movement of the pile (y) at specified depths. These cases usually arise when local data for the soil response are available. To use external p-y curves, the needs to select Input p-y Curves under the p-y Curve Soil Model column in the Soil Layers window. Then, clicking on the context-sensitive button in the far right column opens a window where the can input the effective unit weight of the soil. Finally, the can define lateral deflection and soil resistance values for points in the upper and lower curves by clicking on the corresponding External p-y Curve for Layer button in the far right column. A general description for the data needed under each column for the subwindow option of -Input p-y Curves is listed below: 1. Point: This is a sequential number that is provided to each point of the soilresistance curve that is being defined. This number is automatically provided by the program as new rows are added. The maximum number of points in each soilresistance (p-y) curve is limited to 17 and the minimum is 2. 2. Lateral Deflection: y Values of lateral movement must be inputted in units of length. As a reference, a review of the theory of “Soil Response” is included in Part II, Chapter 3 of the Technical Manual. 3. Soil Resistance: p Values of load transfer must be inputted in units of load per unit depth. As a reference, a review of the theory of “Soil Response” is included in Part II, Chapter 3 of the Technical Manual.

3-7 Shear-Resistance Curve at Pile Tip

This menu option allows the to enter a shear-resistance curve at the bottom of the pile. This menu option is inactive under default conditions. A maximum of 15 points may be defined in the shear-resistance curve at the pile tip. A minimum of two points are required to form a curve.

27

Chapter 3 – Input of Data In general, shearing resistance at the pile tip would only be applicable to those cases where the pile is short (with only one point of zero deflection along their depth). In addition, these curves would only make noticeable differences when using large diameter shafts.

3-8 p-y Modification Factors

This menu option allows the to enter modification factors for soil resistance (p) and/or lateral movement of the pile (y) at specified depths. A maximum of 30 entries of modification factors for p-y curves may be used in an analysis. The program allows the input of modification factors for any depths of the soil profile. The p-y modification factors only apply to p-y curves that are internally generated by the program. If the requests the printout of internally-generated p-y curves, outputted curves will include the changes produced by the specified p-y modification factors. •

Depth: These values represent the depths where modification factor for p-y curves are being specified. Intermediate values of p-y modification factors located between two specified depths are obtained by linear interpolation of the specified factors. It is therefore necessary to have at least two entries of modification factors. Modification factors must be inputted in ascending order of depths.

•

p-Multiplier: The p-multiplier values may be larger or smaller than one. However, in most cases these values are smaller than one to for group effect of closely-spaced piles or drilled shafts. A large reduction in p-values (and/or increase of y-values) may also be used to represent liquefiable layers of sand.

•

y-Multiplier: The y-multiplier values may be larger or smaller than one. However, in most cases these values are larger than one to for group effect of closely-spaced piles. A large increase in y-values (and/or reduction of p-values) may also be used to represent liquefiable layers of sand.

3-9 Output Depths of p-y Curves

28


3-10 Axial Thrust Loads for Interaction Diagram

3-11 Traditional Loading Analysis 3-11-1 Pile Head Loading and Options

29


This menu option allows the to enter the desired boundary conditions and corresponding loading at the pile head. There are five options for boundary conditions at the pile head. The selects the desired boundary condition using a dropdown list of the choices described below. The program allows up to ten rows of boundary conditions and corresponding loading at the pile head. •

Pile-Head Loading Types

1. Shear and Moment: This boundary condition is selected to specify values of applied lateral load in units of force and applied moment in units of force × length at the pile head. This condition implies that the pile head is free to rotate and move laterally. The lateral force is considered positive when applied from left-to-right. The moment is considered positive when applied clockwise. 2. Shear and Slope: In this boundary condition, the defines the applied lateral load in units of force and the slope in radians at the pile head. The lateral force is considered positive when applied from left-to-right. The slope is positive when the pile head rotates counterclockwise. A fixed-head condition (with no restrictions to lateral movements) may be modeled by specifying a slope equal to zero. 3. Shear and Rotational Stiffness: For this boundary condition, the defines the applied lateral load in units of force and a value for rotational stiffness (moment per radian of rotation) at the pile head. The lateral force is considered positive applied from left-to-right. The values for rotational stiffness are always positive. A fixed-head condition (with no restrictions to lateral movements) may optionally be modeled by specifying a large value of rotational stiffness. This boundary condition should be selected if the wants to model an elastically-restrained type of pile-head connection. 4. Displacement and Moment: This is selected to specify values of lateral displacement nd moment at the pile head. The displacement is considered positive applied from left-to-right. The moment is considered positive when applied clockwise.

30

Chapter 3 – Input of Data 5. Displacement and Slope: This is selected to specify values of lateral displacement and the pile-head slope in radians. The displacement is considered positive applied from left-to-right. The slope is positive when the pile head rotates counterclockwise. Load 1: This value is the first load in the loading type description; shear force for the first three loading type conditions and displacement for the last two loading type conditions. Load 2: This value is the second load in the loading type description. Axial Load: This value is input in units of force. It is applied at the pile head and may be entered after specifying the boundary conditions as well as the corresponding loading. Axial loads entered in this column are only used to for secondary moments produced when the pile deflects (also known as P-Δ effects). Compute Top Y vs. L: This column contains a drop-down yes/no option for performing computations of top deflection versus pile length for this pile head loading condition if pile-head loading condition does not prescribe the pile-head lateral deflection value. No computations of top deflection versus pile length will be made if either of the displacement-moment or displacement-slope pile-head conditions is specified. 3-11-2 Distributed Lateral Loading

To model a distributed lateral loading anywhere along the length of the pile, the should check the box next to Include Distributed Lateral Loads, then click the Enter Distributed 31

Chapter 3 – Input of Data Lateral Loads button to open up a window for inputting depth and lateral load intensity. The program allows up to ten different inputs of lateral load values, which are placed in units of load per unit depth. The must enter values in increasing magnitudes of depth. The program linearly interpolates the values of lateral loads existing between specified depths. At least two entries (two depths) of distributed lateral loads are needed. 3-11-3 Lateral Soil Movements

This table allows the to specify free-field soil movement in the soil profile. The soil movement may be deflection along only a portion of the pile length if desired. In general, a pile under lateral load moves against a soil mass. However, in some cases, the soil itself will move and the soil loading or reaction must be considered by taking into the relative movement between the soil and the pile. LPile 6 will automatically generate the soil reaction at each pile increment based on the relative movement between the soil and pile at that particular depth. A maximum of 50 entries is allowed for definition of the soil movement profile in an analysis. •

Depth Below Pile Head: These values represent the x-coordinate corresponding to the depth where the soil move. Intermediate values of soil movement located between two specified depths are obtained by linear interpolation of the specified values. It is therefore necessary to have at least two entries of depths. Soil movement must be inputted in ascending order of depths.

•

Lateral Soil Movement: The soil movement values may be positive for soil moving from left to right or negative for soil moving from right to left. However, it is critical that the soil movement occurs in the same direction of as the applied loads.

3-12 Load and Resistance Factor Design 3-12-1 Unfactored Loads

32


3-12-2 Load and Resistance Factors The controls the definition of load cases either by reading the LRFD load case data file from the Options dialog box or by entering the specific load case. To include a load type in a a load case combination, the enters a positive, non-zero value. In addition, the may enter the resistance factors for structure resistance in bending and shear capacity and may also enter a descriptive name for the load case combination. The current version of LPile does not compute structural shear capacity, so the resistance factor for shear is not used by the program and does not need to be entered. However, if the resistance factor for shear is defined and saved the in the LRFD load case data file, future versions of LPile that do compute shear capacity will be able to use the input value for this factor.

33


3-12-3 Summary of Factored Load Cases The summary of factored load cases is provided for the to view the factored loads computed by LPile. LPile computes this summary by first adding all pile-head loading of the same type together, then multiplying the sum by relevant load factor. In the case of distributed loads, the program integrates the individual distributed load profiles and computes the equivalent concentrated forces at nodes on the pile, adds all forces from the same load type together, then multiplies the sum by the relevant load factor.

34

Chapter 4 Graphics 4-1 Introduction The Graphics menu is used to display graphs of output data provided by a successful program run. Options for the display of graphs under this menu are only enabled after a successful run has been made. Even after performing successful runs, some graphing options may be disabled since the types of output are controlled by the program options enabled.

4-2 Graphics Mouse Commands The following mouse commands are available within a graphic window: Action

Event Description

Mouse Left Click and Drag

Magnifies the area within the drag/release

Mouse Right Click

Zoom out

Mouse Double Click on Legend

Turns the selected curve on/off

4-3 Types of Graphics Two types of graphics are provided by LPile; fast graphics and presentation graphics. Fast graphics are graphs that can be displayed either from the Graphics pull-down menu or by clicking a button on the speedbutton bar. Fast graphics have limited features for modifying the graphs and their contents. Presentation graphics are displayed using the presentation graphics command from the Graphics pull-down menu or by pressing the button on the speedbutton bar.

4-4 Fast Graphics 4-4-1 View Pile-Soil Geometry This menu option is used to display a graphical representation of the side view of the modeled pile and soil layers. This command option becomes active after data of Pile Properties, Soil Layers, Soil Weight, and Soil Strength have been entered under the Data menu, or when opening previously-executed data files. 4-4-2 p-y Curves LPile 6 is capable of generating graphs of internally-generated p-y curves at specified depths located between the lower of the ground surface or top of pile and the pile tip. This graphics option is enabled if the asked the program to print p-y curves for verification purposes by checking in the Options dialog (see Section 3.3.3 for further information). When specified, the graphics screen will show the p-y curves for all specified depths.

35

Chapter 4 – Graphics 4-4-3 Deflection vs. Depth The may select this command option to display a graph lateral deflection versus depth for the modeled pile. This curve is automatically generated in all analytical runs of a laterally-loaded pile. The number of points on the deflection curve is equal to the selected number of pile increments. Several curves may be contained in this graphics if the selects to input several load cases. 4-4-4 Moment vs. Depth The may select this command option to display a graph bending moment versus depth for the modeled pile. This curve is automatically generated in all analytical runs of a laterally-loaded pile. The number of points on the moment curve is equal to the selected number of pile increments. Several curves may be contained in this graphics if the selects to input several load cases. 4-4-5 Shear vs. Depth The may select this command option to display a graph of shear versus depth for the modeled pile. This curve is automatically generated in all analytical runs of a laterally-loaded pile. The number of points on the shear curve is equal to the selected number of pile increments. Several curves may be contained in this graphics if the selects to input several load cases. 4-4-6 Soil Reaction vs. Depth The may select this command option to display a graph of soil reaction versus depth for the modeled pile. This curve is automatically generated in all analytical runs of a laterally-loaded pile. The number of points on the soil-reaction curve is equal to the selected number of pile increments. Several curves may be contained in this graphics if the selects to input several load cases. 4-4-7 Load vs. Top Deflection This menu option is enabled if the specifies two or more load cases in the input data. The specified load cases must have varying lateral loads with or without changes in applied moments or applied axial loads. The may select this menu option to display a graph of curve of applied lateral load versus pile-top deflection. 4-4-8 Load vs. Max Moment This menu option is enabled if the specifies two or more load cases in the input data. The specified load cases must have varying lateral loads with or without changes in applied moments or applied axial loads. The may select this menu option to display a graph of applied lateral load versus maximum bending moment along the pile length. 4-4-9 Pile Length vs. Top Deflection This menu option is enabled if the selects Generate Pile Length vs. Top Deflection option under the Options menu of the input data. The may select this menu option to display a graph of pile length versus pile-head deflections. The should refer to Chapter 3 (Section 3.3.6) for more information about the usage of this curve. 36

Chapter 4 – Graphics 4-4-10 EI vs. Moment This menu option is enabled if the selected to perform a section analysis. The may select this menu option to display a graph of bending stiffness versus bending moment. Values of bending stiffness shown in these curves are used internally in each finite increment of pile analysis when the selects the analysis of pile response with nonlinear EI. The number of curves depends on the number of axial loads specified for section analysis. 4-4-11 Moment vs. Curvature This menu option is enabled the selected to perform a section analysis. The may select this menu option to display a graph of bending moment versus curvature. These curves are helpful to find the ultimate bending moment of the modeled cross section. The number of curves depends on the inputted number of axial loads used for section analysis. 4-4-12 Interaction Diagram This menu option is enabled if the selected to perform a section analysis and inputs several axial load cases for the section analysis. The may select this menu option to display an unfactored interaction diagram (ultimate bending moment vs. axial load) of the modeled cross section. These curves are helpful to find the ultimate bending moment for several axial load cases in the modeled cross section. The number of curves depends on the inputted number of axial loads used for section analysis. 4-4-13 K22 vs. Lateral Load This graphics option is enabled if the asked the program to generate foundation stiffness placing a check mark in Generate Foundation Stiffness under the Options menu. When enabled, the selection of this command option will show a curve of the K22 (or sometimes written Kyy) component of a 6×6 foundation stiffness matrix. The should refer to Chapter 3 (Section 3.3.7) for more information about the usage of this curve. 4-4-14 K23 vs. Lateral Load This graphics option is enabled if the asked the program to generate foundation stiffness placing a check mark in Generate Foundation Stiffness under the Options menu. When enabled, the selection of this command option will show a curve of the K23 (or sometimes written Kyθ) component of a 6×6 foundation stiffness matrix. The should refer to Chapter 3 (Section 3.3.7) for more information about the usage of this curve. 4-4-15 K32 vs. Moment This graphics option is enabled if the asked the program to generate foundation stiffness placing a check mark in Generate Foundation Stiffness under the Options menu. When enabled, the selection of this command option will show a curve of the K32 (or sometimes written Kθy) component of a 6×6 foundation stiffness matrix. The should refer to Chapter 3 (Section 3.3.7) for more information about the usage of this curve.

37

Chapter 4 – Graphics 4-4-16 K33 vs. Moment This graphics option is enabled if the asked the program to generate foundation stiffness placing a check mark in Generate Foundation Stiffness under the Options menu. When enabled, the selection of this command option will show a curve of the K33 (or sometimes written Kθθ) component of a 6x6 foundation stiffness matrix. The should refer to Chapter 3 (Section 3.3.7) for more information about the usage of this curve. 4-4-17 K22 vs. Pile Top Deflection This graphics option is enabled if the asked the program to generate foundation stiffness placing a check mark in Generate Foundation Stiffness under the Options menu. When enabled, the selection of this command option will show a curve of the K22 versus pile top deflection. 4-4-18 K23 vs. Pile Top Deflection This graphics option is enabled if the asked the program to generate foundation stiffness placing a check mark in Generate Foundation Stiffness under the Options menu. When enabled, the selection of this command option will show a curve of the K23 versus pile top rotation. 4-4-19 K32 vs. Pile Top Rotation This graphics option is enabled if the asked the program to generate foundation stiffness placing a check mark in Generate Foundation Stiffness under the Options menu. When enabled, the selection of this command option will show a curve of the K32 versus pile top deflection. 4-4-20 K33 vs. Pile Top Rotation This graphics option is enabled if the asked the program to generate foundation stiffness placing a check mark in Generate Foundation Stiffness under the Options menu. When enabled, the selection of this command option will show a curve of the K33 versus pile top rotation.

4-5 Presentation Graphs This option provides a graphing tool for s to customize the various aspects of a presentation graph, such as font size, line colors, styles, and widths, data point markers, legend text and type, axis and grid scaling, etc. A detailed description of each function and options are given in the associated Help file for the Presentation Graphs tool. Note that it is possible to copy and save the presentation graphs in several graphics formats. In addition, it is possible to copy graphs to the Windows clipboard for easy pasting into word processing or presentation programs. Most s find using the Enhanced Windows Metafile graphics format to be most flexible in use.

38

Chapter 5 Example Problems 5-1 Introduction Several problems are provided herein as examples of different applications that may be solved using LPile 6. Each example focuses on a particular computational feature of the program. Input files for each example are automatically copied to the LPile 6 directory during installation. The data files are named LPile 6 Example X.lp6d, where X represents the desired example number (1 through 15). Example problems provide the information on input and output of various cases, and present a quick tutorial for real-world applications. The is encouraged to study these examples and, with modifications, may use them to solve similar problems. However, by no means can these limited examples explore the full functions and features provided by LPile 6. The main features of each example included with LPile 6 are summarized as follows. Example 1 - Steel pile ing a retaining wall. Among other aspects, this problem uses sample applications of the following program features: •

pile made of a standard structural steel shape,

•

pile with head fixed against rotation,

•

printout of internally-generated p-y curves at different depths for verification purposes,

•

application of several lateral loads, and

•

usage of sloping ground surface.

Example 2 - Bored pile ing a retaining wall. Includes the following program features: •

pile made of a reinforced-concrete section,

•

comparison of values obtained with pile head fixed and free against rotations,

•

application of several lateral loads,

•

analysis with nonlinear bending stiffness, and

•

usage of sloping ground surface.

Example 3 - Steel pile ing an offshore platform. Includes the following program features: •

pile made of two different steel sections,

•

pile with head elastically restrained against rotations, and

•

cyclic loading.

Example 4 - Buckling of a pile column. Includes the following program features: •

pile made of a standard structural steel pipe,

•

pile with head free to rotate, and 39

Chapter 5 – Example Problems •

application of several axial loads.

Example 5 - Ultimate bending moment for bored piles. Includes the following program features: •

reinforced concrete pile of circular cross section,

•

nonlinear materials,

•

printout of interaction diagram, and

•

printout of nonlinear flexural rigidity.

Example 6 - Foundation Stiffness of Concrete Pile with Nonlinear Flexural Rigidity. Includes the following program features: •

reinforced concrete pile of circular cross section,

•

pile with head free to rotate,

•

nonlinear materials,

•

printout of interaction diagram,

•

printout of nonlinear flexural rigidity, and

•

generation of foundation stiffness.

Example 7 - Input of Distributed Load and External p-y Curves. Includes the following program features: •

reinforced concrete pile of circular cross section with two different section properties,

•


•

input of distributed lateral load on a section length of pile with linear variation, and

•

input of externally-specified p-y curves.

Example 8 - Case Study of Piles in Cemented Sands. Includes the following program features: reinforced concrete pile of circular cross section, •


•

input of several lateral loads, and

•

use of internal p-y curves for silts.

Example 9 - Sample of Various Program Options. Includes the following program features: •

drilled shaft with reinforced concrete cross-section and belled bottom,

•


•

sample coordinates for embedded pile head,

•

use of p-reduction factors assuming closely spaced piles,

•

use of several soil layers,

•

input of shear-resistance curve at pile tip, and

40

Chapter 5 – Example Problems •

determination of top deflections versus varying pile lengths.

5-2 Example Problem 1 The general description and geometrical configuration of Example Problem 1 is shown in Figure 5.1. The pile is a standard structural steel shape (HP14x89), two layers of soil are indicated, and the ground surface is sloping downward with respect to the lateral loading. In an actual design, the data shown in this example problem might be for a particular trial run. That is, the selection of the particular section for the pile and its length might change in the course of the computations. Furthermore, the soil profile has been idealized and in an actual case there would almost certainly be a need for consideration of the variation of the soil properties with depth and across the site. 5-2-1 Loading and Boundary Conditions The service load along the pile axis is 88.8 kN (20 kips), if the load factor (global factor of safety) is taken as 2.5, the axial load Q to be used in the computations is 222 kN (80 kips). As it will be seen, the ultimate bending moment is affected only slightly by the presence of the axial load. The sketch of the pile in Figure5.1 shows that its top is fixed against rotation. Thus, it is assumed that the top of the steel section projects a sufficient distance into the reinforced-concrete base of the retaining wall so that no rotation of the top of the pile will occur. This assumption is not strictly true, but research is yet to be done to yield expressions for the rotation of an embedded steel member into a concrete mat. The assumption of pile-head fixity is conservative because the maximum bending moment will occur at the top of the pile and any rotation of the pile head will cause a decrease in the maximum moment. The computations that follow are aimed at finding the lateral load Pt that will cause a plastic hinge to develop at the top of the pile. Secondly, the computations should reveal if there is a possibility of excessive deflection, which is thought to be unlikely for most retaining walls.

Figure 5-1 General Description of Example Problem 1 41

Chapter 5 – Example Problems 5-2-2 Pile Details The strong axis of the pile is perpendicular to the direction of loading, and data for this axis were included in Figure 5.1. From the steel handbook, the width of the section is 373 mm (14.7 in.) and the depth is 351 mm (13.8 in.). The first consideration is the “diameter” to assign to the shape because the recommendations for p-y curves are based strongly on the results of experiments with cylindrical shapes. At the outset, it can be assumed that the soil in the flanges will move with the pile and that it will behave as a rectangular shape. Secondly, the equivalent diameter of the pile can be computed, as a first approximation, by finding a circular section with the same area as the rectangular section. Thus,

πd e 4 64

= (373 mm)(351 mm)

de = 4

64(373 mm)(351 mm)

π

= 408 mm = 16 inches

As shown above, this computation yields a diameter that is less than 10 percent larger than the width of the steel section. Conservatively, then the equivalent diameter can be selected as the width of the pile, or 373 mm (14.7 in.). Designers probably have a tendency to err on the side of conservatism; however, in a particular solution, all of the assumptions should be carefully examined in the light of the principal aim of the solution. The yield moment may be computed by a procedure proposed by Horne (1978). With no axial load and with bending about the strong axis, the yield moment is computed as follows: Considering the effect of axial load: M y = fy × Zx

(

M y = (276 ) 2.39 ×10 −3 M y = 0.660 MN - m M y = 660 kN - m

Considering the effect of axial load:

42

)

Chapter 5 – Example Problems

a=

Px 2t w f y

a=

222 (2)(0.0156)(276,000)

a = 0.0258 mm M y = M y − t w af y M y = 660 − (0.0156)(0.0258) 2 (276,000) M y = 657 kN - m = 5,815 in - kips 5-2-3 Selection of Form of p-y Curves

The loading from a retaining wall is sustained, not repeated, and the designer is faced with the problem of estimating the consolidation and creep of the clay and/or the deflection due to vibration of the sand. The value of shear strength shows that the clay is overconsolidated; thus, as a first approximation, no consolidation or creep is assumed. Also, the sand, well below the ground surface, is assumed not to undergo densification due to possible vibration. These assumptions will need to be carefully considered after a preliminary solution is obtained. The above discussion shows that static loading is appropriate, for both the clay and the sand. Further, the recommendations for stiff clay above the water table are most appropriate. The next step is to find the value of Pt that will cause a bending moment in the pile of 657 m-kN (5,815 in.-kips). The curve shown in Figure 5.6 shows that the maximum bending moment occurs at the top of the pile, where it is assumed to be fixed against rotation. If the pile head is allowed to rotate some, the negative moment at the pile head will decrease and the value of the maximum positive moment, now at a depth of 2.9 m (9.5 ft), will increase. Further, it is of interest to note that, below a depth of 5 m (16.4 ft) the bending moment is virtually zero. Thus, if it were feasible from a practical point of view, the moment of inertia of the pile could be decreased below 5 meters (16.4 ft). 5-2-4 Results of Computations with p-y Curves

The results of the preliminary computations are shown in Figs. 5.2 and 5.3. As may be seen, the computations show that the pile will fail structurally when the axial load is held at 222 kN (50 kips) and the lateral load reaches a value of 410 kN (92 kips). The pile-head deflection at the failure loading was computed to be about 27 mm (1.06 in.). This deflection is not considered to be excessive; therefore, the failure of the pile is taken to be due to the development of a plastic hinge.

43


Figure 5-2 Generated Curve of Lateral Load vs. Maximum Moment for Example Problem 1.

Figure 5-3 Generated Curve of Lateral Load vs. Maximum Moment for Example Problem 1. The safe loading is found by dividing the loading at failure by 2.5, the global factor of safety, or Pt = 164 kN (37 kips) and Px = 88.8 kN (20 kips). The values used as input data for this study are included in section 5.2.5 and the partial listing of the output text is included in section 5.2.6.

44

Chapter 5 – Example Problems The output text contains an echo-print of the input data, along with the values of four internally-generated p-y curves that the requested for printing. The bottom section of the output contains a table with the principal information needed by the engineer, where computed values are given as a function of depth. The table shows that the length of the pile may be decreased to 10 m (33 ft) and that there will be three points of zero deflection, a sufficient number to ensure that the pile behaves as a long pile. By reducing the length of the pile, some unneeded output can be eliminated and, further, the amount of internal computations performed by the computer is reduced. Plots of deflection and bending moment as a function of depth are shown in Figs. 5.4 and 5.5. In a second run for loadings of Pt of 164 kN (37 kips) and Px of 88.8 kN (20 kips), the deflection at the top of the pile was computed to be 4.0 mm (0.16 in.) and the maximum bending moment was 186 m-kN (138.5 ft-kips), a value that is well below the 657 m-kN (485 ft-kips) that would cause the pile to fail.5.2.5 Input Data - Initial Runate, for both the clay and the sand. Further, the recommendations for stiff clay above the water table are most appropriate. The next step is to find the value of Pt that will cause a bending moment in the pile of 657 m-kN (5,815 in.-kips).

Figure 5-4 Curve of Deflection vs. Depth for Example Problem 1

45


Figure 5-5 Bending Moment vs. Depth for Example Problem 1 The curve shown in Figure 5.6 shows that the maximum bending moment occurs at the top of the pile, where it is assumed to be fixed against rotation. If the pile head is allowed to rotate some, the negative moment at the pile head will decrease and the value of the maximum positive moment, now at a depth of 2.9 m (9.5 ft), will increase. Further, it is of interest to note that, below a depth of 5 m (16.4 ft) the bending moment is virtually zero. Thus, if it were feasible from a practical point of view, the moment of inertia of the pile could be decreased below 5 meters (16.4 ft).

46


Figure 5-6 Curve of Bending Moment vs. Depth for the final run of Example Problem 1.

5-2-5 Input and Output Files

The input data and output files have the filename LPile6 Example 1. These file are found in the Examples folder. The filename extensions for the files are shown below. These files are not shown in this ’s Manual due to their length. The filename for the second run is named LPile 6 Example 1 - Run 2. The input and output files are not shown here due to their length. File Type

Filename Extension

Input

lp6d

Output Report

lp6o

Plot Output Data

lp6p

Runtime Message File

lp6r

Plot Title File

lp6t

5-3 Example Problem 2 This example is similar to Example Problem 1, but in this case the steel pile is replaced by a drilled shaft. The soil is the same as that used in Example Problem 1. The problem with a

47

Chapter 5 – Example Problems reinforced-concrete pile is to find the ultimate bending moment and an appropriate value of flexural stiffness (EI) to use in the computations. 5-3-1 Loading and Boundary Conditions

As with the steel pile in Example Problem 1, an axial load of 88.8 kN (20 kips) is assumed. The pile head is assumed to be fixed against rotation in the first loading case and free to rotate in the second loading case. The problem is to find the lateral load for each of these cases that will cause the shaft to fail. Both of these loading cases might be used in a practical problem to bound the solution if the rotational restraint caused by embedment of the top of the pile causes the pile head to be between fixed and free. 5-3-2 Pile Details

A bored pile with an outside diameter of 760 mm (30 in.) and a length of 15.2 m (50 ft) is employed in this example. As shown in Figure 5.7, the reinforcing steel consists of 12 bars with outside diameter of 25 mm (corresponding to No. 8 bars in US practice) and spaced equally around a 610 mm (24 in.) diameter circle. The ultimate strength of the reinforcing steel and the concrete are 414 MPa (60 ksi) and 27.6 MPa (4 ksi), respectively.

Figure 5-7 Cross-section and Interaction Diagram for Example Problem 2.

48


Figure 5-8 Computed values of Bending Stiffness for Example Problem 2 Information for the interaction diagram of this pile section was obtained with an initial program run (using file Exam2.lp6d, included in Section 5.3.5 of this manual) and the result is also shown in Figure 5.7. The computations of ultimate bending moments, My, are based on a concrete strain at failure of 0.003. For the axial load of 88.8 kN (20 kips), the ultimate bending moment, My, was taken from the curve as 725 m-kN (535 ft-kips). The computations could have been done for only the one axial load; however, the interaction diagram was developed in its entirety to demonstrate the influence of axial load for this particular problem. As it may be seen in the previous Figure 5.7, an increase in the axial load up to a point will increase the value of My so the working load was not multiplied by the global factor of safety to get My. To do so would have been unconservative. LPile Plus 6.0 was also used in the same run (using file Exam2.lp6d) to compute values of EI for the axial load of 88.8 kN (20 kips) and as a function of applied moment. The results are shown in Figure 5.8. Because only a short portion of the length of the pile will be subjected to the ultimate moment, an acceptable procedure is to select a constant value of EI for the computations of the response of the pile and to select a value in the proper range of applied moments. The must that the selection of the proper value of EI to use in the computation of the response of a bored pile can also be done by selecting the proper type of analysis under the Options menu, which using a subroutine that will compute a value of EI as a function of axial loading and computed bending moment. Such a procedure would add the requirement for a second iterative process, in addition to iterating to obtain the proper value of soil modulus, Es. 5-3-3 Selection of Form of p-y Curves

The same criteria that were used for Example Problem 1 for the p-y curves are also used for this example.

49

Chapter 5 – Example Problems 5-3-4 Results of Computations with p-y Curves

The results from the computer solutions with a constant bending stiffness of 120 MN-m2 (290,375 kips-ft2) are shown in Figure 5.9. The maximum bending moment and pile-head deflection, as a function of Pt, are shown in the figure. For this particular example, the maximum bending moment for the two cases is almost the same. For a value of My of 725 m-kN (535 ftkips), Figure 5.9 shows that a lateral load of 480 kN (108 kips) will cause a plastic hinge to develop. In the fixed-head case the maximum bending moment occurs at the pile head and in the free-head case the maximum bending occurs at some distance below the groundline. The pile-head deflections for the lateral load of 480 kN (108 kips) for the two cases are quite different, 12 mm (0.47 in.) for the fixed-head case and 50 mm (1.97 in.) for the free-head case. These deflections are for the lateral load that produces the ultimate bending moment but still are tolerable for most retaining walls. The solution of the bored pile was continued by dividing 480 kN (108 kips) by the selected load factor of 2.6, yielding a value of Pt of 185 kN (41.6 kips), and the deflection and bending moment as a function of depth for this service load, or working load, can be found by making runs with the computer. (The selection of a load factor, or global factor of safety, is to be given careful attention by the person in responsible charge. That 2.5 was used in one example and 2.6 in another is intended to show that the factor will vary from case to case. These particular values are not being recommended but are merely selected to allow the examples to be completed).

Figure 5-9 Maximum Bending Moment (Mmax) and Pile-head Deflection (yt) versus Applied Lateral Load (Pt) for Example Problem 2. 50

Chapter 5 – Example Problems The input for the final runs that were made to find the deflection and bending moment as a function of depth along the pile is included in Section 5.3.6 of this manual. The length of the pile may be reduced if there are more than two points of zero deflection, which ensures that the pile acts as a stable pile. The coding allows a series of runs to be made, so the can compare pile length versus deflection at the pile head, as described in page 59 of the Technical Manual. Output graphics for the final run of this example problem, Exam2b.lp6d, are not plotted but the results are included in Section 5.3.7 of this manual. The results show that the computed deflection, yt, for the free-head case was 6.8 mm (0.27 in.) and for the fixed-head case was 1.6 mm (0.06 in.). The bending moment as a function of depth for the two cases is shown in Figure 5.10. The maximum bending moment, Mmax, for the free-head case is 205 m-kN (151 ft-kips) and for the fixed-head case is 230 m-kN (160 ft-kips), but these maximum values occur at different depths, of course. In either case, the reinforcing steel could be eliminated, or greatly reduced, below a depth of 5 m (16.4 ft). If one were able to control the rotational restraint at the pile head at a value between fixed and free, the curves in Figure 5.10 make it clear that the maximum bending moment could be significantly reduced. Perhaps it is of interest to note that the lateral loads that were computed for the steel pile and for the bored pile were of significant magnitude, indicating that vertical piles can be used economically to sustain lateral loads.

Figure 5-10 Maximum Bending Moment (Mmax) versus Depth for Example Problem 2 5-3-5 Input Data - Initial Run 5-3-6 Input Data - Final Run 5-3-7 Output Data - Final Run

5-4 Example Problem 3 The sketch in Figure 5.11 shows a bent from an offshore platform of the type for depths of water of 100 m (328 ft) or more. Hundreds of such structures have been built where a template 51

Chapter 5 – Example Problems is fabricated on shore, barged or floated to the site, and placed by lifting or controlled submergence. For the case indicated, the weight of the jacket causes the extensions of the legs to push into the soil. With the top of the template above still water, piles are stabbed and driven. The tops of the piles are trimmed, and welded to the jacket, and the annular space between the outside of the piles and the inside of the jacket leg is filled with grout. Finally, a deck section is lifted and its columns are stabbed into the tops of the piles and then welded. The soil at the site is not shown in the sketch; it is considered to be soft clay with some overconsolidation at the ground surface but with an increase in strength with depth as for normal consolidation. The assumption is made that scour will occur around the piles to a depth of 1.5 meters (5 feet). The undrained strength of the clay at that depth is 24 kPa (500 psf) and the strength at 30 m is 72 kPa (1,500 psf). The submerged unit weight is assumed to be 9.0 kN/m3 (57 lb/ft3); ε50 is 0.02 at 1.5 m (5.0 ft) and 0.01 at 30 meters (98 feet). 5-4-1 Loading and Boundary Conditions

The sketches in Figure 5.12 show one of the piles from the structure with the rotational restraint given approximately by an equation. The number 3.5 indicates that the bracing has been discounted and that the member is acting as one whose far end is intermediate between fixed and free. The approximation is adequate for a preliminary solution but, for the final analysis, the superstructure and the piles should be considered as continuous, and the piles analyzed as a group. The critical loading occurs during a storm, and Figure 5.11 shows the approximate position of a wave as it moves past the structure. The selection of a particular wave height and velocity of the wind is a problem in statistics, and the factor of safety to be employed is related to those selections. For this problem, it is assumed that a load factor of 2.4 is appropriate. The axial loading of the pile that is analyzed is 1,250 kN (281 kips); thus, the load in the design computations is 3,000 kN (674 kips). A solution consists of finding the lateral loading Pt that will cause a plastic hinge to develop in the pile, and the safe load by dividing that load by the global factor of safety.

52


Figure 5-11 Idealized View of an Offshore Platform, Example Problem 3

53


Figure 5-12 Superstructure and pile details, Example Problem 3 5-4-2 Pile Details

The sketch in Figure 5.12 shows that the pile to a distance of 4.0 m (13.1 ft) from its top consists of two pipes that are acting together. The outside diameter of this combined section is 838 mm (33 in.) and its moment of inertia is 5.876 × 10-3 m4 (4,117 in4). The lower section has an outside diameter of 762 mm (30 in.) and a moment of inertia of 3.070 × 10-3 m4 (7,376 in4). The ultimate strength of the steel for the piles is assumed to be 3.95 × 105 kPa (57,290 lb/in2). Figure 5.13 shows the results of computations for the ultimate bending capacity of the upper sections of the pile in the example. As shown in the Technical Manual, the stress-strain curve for the steel is bilinear; thus, the ultimate bending moment will continue to increase slightly as the full section of the pile approaches the plastic range. It was decided to accept the value of Mult as the value where the maximum strain is 0.015 which is five times that of concrete. For the upper section, a value of 7,100 m-kN (5,237 ft-kips) was computed. The corresponding value for the lower section of the pile was 4,280 m-kN (3,157 ft-kips).

54


Figure 5-13 Bending Moment vs. Curvature, Example Problem 3. 5-4-3 Selection of Form of p-y Curves

The soil conditions at the site are in the range of soft clay below the water, and the recommendations for that soil are employed in the computations. Cyclic loading is employed because the design is to reflect the response of the structure to a storm. Some comment is needed about the number of cycles of loading. If the documentation is reviewed for the experiments that resulted in the development of the recommendations, it will be noticed that the cycles of loading were continued until an apparent equilibrium was reached; thus, the criteria reflect the limiting condition (or worst condition). However, during a particular storm, there may be only a small number of loads of the largest magnitude during the peak of the storm. Therefore, the recommendations may be somewhat more conservative than necessary, but at the present, recommendations are unavailable to allow the introduction of the number of cycles into the procedure. 5-4-4 Results of Computations with p-y Curves

In reference to the previously shown Figure 5.12, initial computations were necessary to learn if the lateral loading on the selected pile would cause a critical moment in the upper or lower section. A series of computer runs and plots were made of the maximum moment as a function of Pt for both the upper and lower sections. Figure 5.14 shows that the maximum moment for the upper section, 7,100 m–kN (5,237 ft-kips) and negative in sign, occurred with a lateral load of 1,163 kN (261 kips). At that value of Pt, the maximum moment for the lower section was about 2,500 m-kN (1,843 ft-kips), which was far less than the yield value of 4,280 m-kN (3,157 ft-kips). Thus, the upper section of the pile controls the loading. The deflection of the top of the pile, yt, for the failure loading of 1,163 kN (261 kips) was computed to be 319 mm (12.6 in.) and, in some designs, the deflection might have controlled the

55

Chapter 5 – Example Problems loading. However, the computed deflection will be much less when the factored load is used; furthermore, excessive deflection is rarely a problem in the design of an offshore platform. It is true that personnel could experience distress on a deck that was moving radically; however, in normal circumstances, the personnel are removed from the platform during the occurrence of the design storm. Employing a load factor of 2.4 (global factor of safety), the service value of Pt is 485 kN (109 kips) and, as noted before, the value of Q is 1,250 kN (281 kips). The input data for the run is included in Section 5.4.5 of this manual and the resulting moment diagram is shown in Figure 5.15. The computed value of yt, not plotted here, was 59 mm (2.32 in.) which is undoubtedly acceptable. The output text for this study, in summary form, is included in Section 5.4.6 of this manual. A study of Figure 5.15 shows that the moment diagram is virtually zero below the depth of 15 m; therefore, the selection of the thickness of the wall of the pile below this depth will be based on the requirements of installation, rather than loading. Further, it is evident that the maximum bending moment could be reduced significantly if the designer has some control over the value of the rotational restraint at the mudline. Thus, the opportunity exists for minimizing the cost of the foundation by a judicious selection of the manner in which the piles are ed to the superstructure. For example, a less expensive solution could have been achieved if shims had been used at the bottom of jacket-leg extension and at the ts, with the result that no grouting would have been needed. Finally, the heavy-walled section of the pile, whatever the final design, will be needed in the top 15 m (49.2 ft); therefore, the stratigraphy and methods of installation must be such that the pile can be installed to the proper depth.

Figure 5-14 Results of initial computation with p-y curves, Example Problem 3

56


Figure 5-15 Bending moment as a function of depth, Example Problem 3 5-4-5 Input Data 5-4-6 Output

5-5 Example Problem 4 Buckling of a Pile-Column A special feature of the p-y method is that a solution can be obtained for the load that will cause the buckling of a pile that extends above the groundline. It is not often that such a problem is encountered in practice but a rational solution is much to be desired if such problems do occur. Loading and Boundary Conditions The lateral load at the pile head is 44.5 kN (10 kips) and the loading was static. The lateral load and the axial load are to be applied at the top of the pile which was 2.54 m (8.3 ft) above the groundline. The bending moment at the pile head will be zero. The solution to the problem seeks the same answer as does the Euler solution for a column but, because the response of the soil is nonlinear, an eigenvalue solution is inapplicable. Rather, the answer is obtained by successive solutions of the nonlinear, beam-column equation with the axial load being increased until excessive deflection is computed. Pile

57

Chapter 5 – Example Problems The pile is a steel pipe, 373 mm (14.7 in.) in outside diameter, and with a wall thickness of 22 millimeters (0.87 inch). The EI is 7.52 × 104 kN-m2 (2.62 × 1010 lb-in2). The length is 15.2 meters (50 feet). Had the portion of the pile above the groundline been more than 2.54 m (8.33 ft), the buckling load that was found would have been much less than shown below. Selection of Form of p-y Curves The soil is a sand with an angle of internal friction of 35 degrees. The water table is below the tip of the pile and the sand has a unit weight of 19 kN/m3 (121 lb/ft3). The p-y curves for static loading of sand above the water table are appropriate for the problem. Presumably, the soil properties are those that exist after the pile has been installed. Results of Computations with p-y Curves The input values are shown in Table 1.5 and the results from the p-y method are shown in Figure 1-13. The deflection at the top of the pile, as a function of Px, is shown in Figure 1.13a and the maximum bending moment in Figure 1.13b. Lines drawn asymptotic to the curves give a buckling load of about 4,500 kN (1,012 kips). While the solution to the problem appears to be rather straightforward, there presently are no other rational ways to take the response of the soil into in solving for the buckling loading of a pile. It is also of interest to note that the same type of solution can be used to investigate the effect of the eccentric application of axial loading and the effect of accidental batter.

58


Figure 5-16 Results from computer solution for buckling load, Example Problem 4

5-6 Example Problem 5 Example Problem 5 is included to illustrate functions of program LPile 6 for computing the ultimate bending moment and to form an interaction diagram. A total of eight axial loads are specified for the program to compute the ultimate bending moment at each axial load and to construct the interaction diagram (ultimate bending moment versus axial load). Only the tables of output for axial load of 0 kips, 100 kips, and 500 kips are shown in the following pages. The ultimate bending moment of a reinforces-concrete section is taken at a maximum strain of concrete of 0.003 based on the ACI code. It should be noted that the flexural rigidity (EI), corresponding to the ultimate bending moment, is significantly lower than that of the uncracked EI value. Therefore, the should also pay attention to the variation of EI versus moment as shown in the first two columns in the output summary. In general, the moment 59

Chapter 5 – Example Problems distribution is not much affected by the EI used in the computation. However, if the deflection is more critical for the design, then careful interpretation of EI should be done. As shown in Figure 5.17, three ranges of EI magnitude can be found in the output. The first range of EI magnitude is associated with the uncracked stage. The concrete is uncracked and the EI is more-or-less constant and is equal to the calculated EI for the gross section. The second range of EI magnitude is for the cracked stage. A significant decrease in the EI value takes place as cracks continue propagating. The third range of EI magnitude is for the cracked and large strain stage. The EI value is further reduced because the concrete stress-strain curve (shown in the Technical Manual) is softened at large strains. The resulting interaction diagram for the reinforced concrete section is shown in Figure 5-18. The input and output data for this problem are included in Section 5.6.1 and 5.6.2 of this manual.

Figure 5.17 Flexural rigidity versus applied bending moment, Example Problem 5

60


Figure 5-18 Interaction diagram of reinforced-concrete pile section, Example Problem 5 5-6-1 Input Data 5-6-2 Output Data

5-7 Example Problem 6 This example is presented to illustrate the capability of Program LPile 6 to perform analyses that can yield results of direct benefit to the designer of a reinforced-concrete pile. The pile is 30-inches in diameter and 25-ft in length. The pile is embedded in a dense sand with an internal friction angle of 38 degrees. In general, with input information provided for reinforcement in the same data file, the program will compute the ultimate bending moment as the first step. Loading and preliminary data on piles are selected, and the program yields values of pile deflection, moment, shear, and soil resistance as the second step. The can then compare the maximum bending moment computed in the second step with the ultimate bending moment in the first step for an allowable factor of safety. The properties of the pile can then be changed, if necessary or desirable, and further computations made to achieve the final selection of the properties of the pile. The EI values used on a given pile may have a significant effect on the resulting deflections of the modeled pile. The relationship between bending moment and EI is computed during the first step of this example application. The can ask the program to include the nonlinear moment-versus-EI variation directly into the computations. Alternatively, the may also manually input the justified EI values for different pile sections, based on the curve of bending moment versus depth obtained earlier. In this example, the option for automatic

61

Chapter 5 – Example Problems iterations using internally-generated, cracked/uncracked EI values was given to the computer for the final solution. The procedure that is illustrated is, of course, only one aspect of the design of a pile but is certainly an important one. The input and output data for this study are included in Sections 5.7.1 and 5.7.2 respectively. In many computer programs for superstructure analyses, the is allowed to input spring stiffnesses to represent foundations under column bases. To demonstrate another useful tool of LPile 6, this example problem includes a check mark on the option to generate the foundation stiffness matrix. Since the program only deals with lateral loading, only four components of a 6x6 stiffness matrix are generated. Values for the axial spring stiffness should be generated using other tools. In general, values are nonlinear in nature and only valid for a certain range of loading. Iterations might be necessary to achieve convergence between superstructure and pile analyses. Output curves obtained from this example problem for the Kyy and Kθθ stiffness-matrix components are shown in Figs. 5-19 and 5-20.

Figure 5.19 K22 Stiffness Matrix Component, Example Problem 6

62


Figure 5-20 K33 stiffness-matrix component, Example Problem 6

5-7-1 Input Data 5-7-2 Output Data

5-8 Example Problem 7 This example is included to illustrate a common case in which a 16-in. (406 mm)diameter pipe pile is subjected to both, concentrated loads at the pile head and distributed loads along the pile. The head of the pile will be assumed unrestrained against rotations (free-head case) with no applied moment. A lateral load of 5 kips (22 kN) will be applied at the pile head. The non-uniform distributed loads are 20 lb/in (3.5kN/m) at the depth of 2 ft (0.6 m) and linearly increase to 100 lb/in (17.5 kN/m) at the depth of 5 feet (1.5 meters). Figure 5.21 shows a general view of the pile and soil. The distributed load in this case occurs over a pile length of 5 feet (1.5 meters), and an increment length of 0.5 feet (0.15 meters); therefore, the distributed lateral load can be properly reflected by the 10 increments of length of the pile. To demonstrate another feature of LPile 6, the p-y curves shown in Figure 5.21 will be inputted externally for this solution. The program interpolates linearly between points on a p-y curve and between depths of p-y curves. In this example, the deepest p-y curve is at 188 inches (4.8 meters). For any nodes on the pile that extend below the depth of the deepest curve, the program uses the deepest p-y curve for computation. The input and output data for this study are included in Sections 5.8.1 and 5.8.2 respectively.

63


Figure 5-21 Pile and soil details for Example Problem 7

5-8-1 Input Data 5-8-2 Output Data

5-9 Example Problem 8 A field test for behavior of laterally-loaded, bored piles in cemented sands (c-φ soil) was conducted in Kuwait (Ismael, 1990). Twelve bored piles that were 11.8 in. (0.3 m) in diameter were tested. Piles 1 to 4 were 10-ft (3-m) long, while piles 5 to 12 were 16-ft (5-m) long. The study was directed at the behavior of both single piles and piles in a group. The measured load versus deflection curves at the pile head for a 10-ft (3-m) long single pile and a 16-ft (5-m) long single pile are presented in the paper and can be studied by using the soil criteria for c-φ soils.

64

Chapter 5 – Example Problems The piles were reinforced with a 9.8-in (0.25-m) diameter cage made of four 0.87-in (22mm) bars for the 10 ft (3 m)-long piles and six 0.87-in (22-mm) bars for the 16 ft (5 m)-long piles. In addition, a 1.42-in (36-mm)-diameter reinforcing bar was positioned at the center of each pile. The Young's modulus for concrete was measured during a cylinder test and a representative value of 3,200 psi (22 MPa) was selected. The flexural rigidity EI varies with the applied moment but a constant value was reported. After lateral-load tests were completed, the soil to a depth of 6.5 ft (2 m) was excavated to expose strain gauges. The pile was reloaded and the curvature was found from readings of strain. The flexural rigidity was calculated from the initial slope of the moment-curvature curves as 7.0 × 109 lb-in2 (20.2 MN-m2) which seems to be in a reasonable range. The subsurface consisted of two layers as shown in Figure 5.22. The first layer, described as medium dense cemented silty sand, was about 11.5 ft (3.5 m) in thickness. The values of c and φ for this layer were found by drained triaxial compression tests and were 2.9 psi (20 kPa) and 35 degrees respectively. The first layer was underlain by medium dense to very dense silty sand with cemented lumps. The values of c and φ were zero and 43 degrees, respectively. LPile 6, employing the c-φ criteria was used to predict curves of load versus deflection at the pile head for both the 10-ft (3-m) pile and the 16-ft (5-m) pile. Good agreement was found between measured and predicted behavior, as shown in Figs. 5.23 and 5.24. The input data and a summary of the output for the 16-ft (5-m) pile for this study are included in Sections 5.9.1 and 5.9.2 respectively.

Figure 5-22 Soil details for Example Problem 8

65


Figure 5-23 Comparison between measured and predicted load-deflection curves for the single 5-m (16-ft) pile of Example Problem 8

66


Figure 6-24 Comparison between measured and predicted load-deflection curves for the single 3-m (10-ft) pile of Example Problem 8 5-9-1 Input Data 5-9-2 Output Data

5-10 Example Problem 9 This example application has been prepared for an idealized drilled shaft whose head is embedded 12 in. (0.30 m) in soil. The shaft is assumed to have a 20-ft (6.1-m) long straight section of 3-ft (0.91-m) diameter and a 4-ft (1.22-m) long section with a 11-ft (3.35-m) diameter bell at the bottom. The general pile geometry is shown in Figure 5.25. The soil stratigraphy is assumed to be made of four different layers of sand, soft clay, silt and stiff clay. The soil properties and depths are also shown in Figure 5.25. The loads shown acting at the top of the pile in Figure 5.25 are mainly axial and the pile must be checked to withstand the given axial loading using a different program. The LPile run is performed to check the lateral behavior and to help design the shaft reinforcement. A first run of the problem showed that the shaft acted mainly as a short pile with lateral movements observed at the bottom of the shaft. The designer then decided to for the additional amount of soil resistance provided by the large shear forces developed at the enlarged base of the shaft. This was accomplished by placing a checkmark on the option to include shear resistance at pile tip. Lateral movements at the pile head was reduced to below the design67

Chapter 5 – Example Problems specified 0.8-in. maximum deflection. The consideration of shear resistance at the pile tip produced a total 0.5-in. reduction in pile-head deflection. The computer-generated p-y curves were reduced to for closely-spaced piles by utilizing p-reduction factors that varied from 0.75 in the straight shaft and 0.3 in the belled portion. In addition, the program was asked to generate a plot of pile length versus pile-top deflections in order to optimize the design length. The resulting plot included in Figure 5.26 shows that the pile length should not be further reduced in order to have an appreciable factor of safety from the critical length.

Figure 5-25 Shaft and soil details for Example Problem 9

68


Figure 5.26 Pile length vs. top deflection, Example Problem 9 5-10-1 Input Data 5-10-2 Output Data

69

Chapter 6 Validation 6-1 Introduction Two approaches are used to validate the output of the computer program. Firstly, case studies are shown that give the comparison of maximum bending moments from experiment and from computation. Secondly, suggestions are made for checking the output to ensure that the equations of mechanics are satisfied.

6-2 Case Studies The technical literature contains a significant number of cases where results of the tests of piles under lateral load are presented; however, in only a small number of these experiments are the values of bending moment reported from instruments along the pile. The case studies presented herein are concerned with these latter cases because the failure of a pile is most frequently due to the development of a plastic hinge. Table 6.1 gives a list of the cases where bending moment was measured. The table shows the location of the experiment, the reference, a general description of the soil and the position of the water table, the computed lateral load at a load factor of 2.5, and the kind of pile and its size. For each of the cases, a preliminary computation was made, using the analytical methods presented herein, to find the lateral load Pult that would cause the maximum bending moment Mult to occur. The next step was to find the experimental bending moment and the computed bending moment at the load of Pult/2.5. The reason for the comparison at the reduced loading is that the load actually applied to the pile would be reduced by a factor of safety and a value of 2.5 is reasonable. Figure 6.1 presents a comparison of maximum bending moments from computations and from experiment. As it may be seen in the figure, the agreement is excellent. However, it is important to indicate that some of the experiments were used to develop the criteria for the response of soils under lateral loading that are used in the analyses. Nevertheless, the validity of those experiments cannot be questioned as reflecting the behavior of piles under lateral loading, particularly where the loading was cyclic. Obviously, additional experiments with instrumented piles are to be highly desired. Table 6.1 Comparison of bending moments from computer runs and case studies Test No.

Location of Test

Reference

Soil

Position of Water

1 2 3 4 5 6 7 8 9 10 11

Japan (static) Lake Austin (static) Lake Austin (cyclic) Sabine (static) Sabine (cyclic) Houston (static) Houston (cyclic) Manor (static) Manor (cyclic) Arkansas R. (static) Mustang Is. (static)

Japan (1965) Matlock, (1970) Matlock, (1970) Matlock, (1970) Matlock, (1970) Reese & Welch (1975) Reese & Welch (1975) Reese el al. (1975) Reese el al. (1975) Alizadeh (1970) Reese el al. (1974)

Clay Clay Clay Clay Clay Clay Clay Clay Clay Sand Sand

At mudline Above mudline Above mudline Above mudline Above mudline At 5.5 m At 5.5 m Above mudline Above mudline At 1.0 m Above mudline

70

Pult/2.5 Computer Results kN 22 116 44 53 27 196 196 254 142 196 182

Kind of Pile Steel, 305 mm OD Steel, 324 mm OD Steel, 324 mm OD Steel, 324 mm OD Steel, 324 mm OD Reinf. Conc. 762 mm OD Reinf. Conc. 762 mm OD Steel, 641 mm OD Steel, 641 mm OD Steel, 254 mm OD Steel, 610 mm OD

Chapter 6 – Validation 12

Mustang Is. (cyclic)

Reese el al. (1974)

Sand

Above mudline

182

Steel, 610 mm OD

Figure 7-1 Comparison of maximum bending moments from computational runs and from experimental case studies

6-3 Verification of Accuracy of Solution The best policy for a of a computer program is to assume that the output is in error unless a check is made. There are many "scare" stories about accepting computer output as valid only to learn later, perhaps after some kind of failure, that the output was in error. One kind of check that is valid is that the has made many solutions with the computer and has a good idea of what the output should be. Not many engineers are that fortunate with regard to the problem presented herein. Other kinds of checks that can be made are shown in the following paragraphs. 6-3-1 Solution of Example Problems

A number of example problems have been coded and solved using LPile 6 and the results are included in Chapter 5 of the ’s Manual. The should code some of the example problems on occasion to see if identical results, or nearly identical, are obtained. Another example problem was run and is shown in the following pages. The output from this example problem will be checked to illustrate some of the procedures employed for verification.

71

Chapter 6 – Validation 6-3-2 Check of Echo Print of Input Data

This check is easy to make and should always be carried out. The entering of incorrect data is a frequent error; the coding of the program to allow for echo printing should prevent such errors. For instance, the output text for the example problems in Chapter 5 of the ’s Manual are listed individually, and the echo print of the input data is included in each output file. In each application problem the may always compare that the echo print data in the output file reproduces their desired input parameters. 6-3-3 Investigation of Length of Word Employed in Internal Computations

The assumption is made that the computer being used is capable of double-precision arithmetic, yielding about 10 or 12 significant figures or more. The should be satisfied on this point before making computations; the difference-equation method requires that a relatively large number of significant figures be employed in order to avoid serious errors. 6-3-4 Selection of Tolerance and Length of Increment

The tolerance is a number that is part of the input to be used in making a particular run. The values of deflection for successive iterations are retained in memory and the differences at corresponding depths are computed. All of the differences must be less than the tolerance to conclude a particular run with the computer. The tolerance that was used in the example problems of Chapter 5 of the ’s Manual, and in the study of this Chapter, was l × 10–5 m (3.9 × 10–4 in.), which is the default value provided by the computer program. The has control over the tolerance, but the default value appears to be a good selection. Had a significantly larger value been selected, inaccurate computations would have resulted; had a significantly smaller value been selected, the number of iterations would be increased and, in fact, a very small value would prevent convergence. Verification of accuracy in the solution of the difference equations has been demonstrated and results agree closely with those from the closed-form solution. Also, the exercise presented below demonstrates to a certain extent that accurate solutions are being obtained. Convergence is usually obtained with 12 to 15 iterations, which does not require much time on most computer systems. The must select the length of the subdivisions into which the pile is divided. The total length of the pile is the embedded length plus the portion of the pile above ground, if any. The first step in the selection of the length of increment is to eliminate the lower portion of the pile if there are several points of zero deflection. The behavior of the upper portion of the pile is unaffected as the length is reduced to the point where there are at least two or three points of zero deflection. The number of points of zero deflection is listed on the output for convenience. A possible exception to shortening the pile to facilitate the computations may occur if the lower portion of the pile is embedded in rock or very strong soil. In such a case, small deflection could generate large values of soil resistance that in turn could influence the behavior of the upper portion of the pile. With the length of the pile adjusted so that there is no exceptionally long portion at the bottom where the pile is oscillating about the axis with extremely small deflections and soil resistances, the may wish to make a few runs with the pile subdivided into various numbers of increments. Such a study was done for the example shown in this chapter. Figure 6.2 shows a 72

Chapter 6 – Validation plot of the computed values of groundline deflection and maximum bending moment as a function of the number of increments into which the pile is subdivided. These values become virtually constant with the pile subdivided into 50 increments or more. Errors are introduced if the number of increments is 40 or less. Errors would have been introduced if solutions had been made for large numbers of increments, at some point beyond 250. The computed deflections at successive increments would have been so close to each other that differences would have disappeared and round-off errors would have been introduced. The number of increments at which such errors are introduced will depend, of course, on the number of significant figures employed in the computations of the particular computer being used. The computer used for the examples presented herein, with the code using double-precision arithmetic, employs 8 bytes of storage for a real value, which translates into a word length of approximately 15 decimal digits. For the particular problem that was solved, the pile length was 12.7 m (42 ft) and the diameter was 0.914 meters (36 inches).

Figure 6.2 Influence of length of increment on pile-head deflection and maximum bending moment

The increment length at which good results apparently were obtained was 0.25 m (10 in.) (corresponding to 50 increments) which is about one-third or one-forth of the pile diameter. It is not only the pile diameter but the relative stiffness of the pile compared to the stiffness of the soil that controls the results. The particular runs from which Figure 6.2 was plotted were made with a PC employing an Intel Pentium 120 microprocessor. Research has not been done that would allow a code to be written to enable the computer to select automatically the optimum number of increments for a particular problem. Therefore,

73

Chapter 6 – Validation the will need to do a few studies such as the one demonstrated here in order to be able to select the increment length that will yield an acceptable solution. 6-3-5 Check of Soil Resistance

The output text that is used for the verification of the correctness of the computer results is shown in Section 6.3.10. The pile, with a length of 12.7 m (42 ft) and a diameter of 0.914 m (36 in.), was assumed to be installed in sand with an angle of internal friction of 35 degrees and a unit weight of 18.7 kN/m3 (119 lb-ft3). The top of the pile is unrestrained, a lateral load of 445 kN (100 kips) is applied, and the loading is static. The complete listing of input values that were used in the validation problem is included in Section 6.3.9. As shown in the output text of Section 6.3.10, a p-y curve was printed for a depth of 1.52 meters (5 feet). Initially, it will be assumed that the curve is correct. Also in the output text of Section 6.3.10, the deflection at a depth of 1.52 m (5 ft) is shown as 0.00704 m (0.28 in.) and the soil reaction is 205 kN/m (1,170 lb/in.). The linear interpretation of the p-y curve that is printed for the depth of 1.52 m (5 ft) is as follows. Px = 203.98 kN/m (1,165 lb/in) The close agreement in the tabulated and computed values of soil resistance is reassuring. Some difference would not have been unexpected between the two values of p because the computer uses the equations for the p-y relationship and the check was done by linear interpolation. The next step is to ascertain that the p-y values that are printed are consistent with the equations that are given in Part II of the Technical Manual. As noted in the computer output, the loading is static, the soil is sand with an angle of internal friction of 35 degrees, and a unit weight of 18.7 kN/m3 (119 pcf). The pile has a diameter of 0.914 m (36 in.) and the initial modulus of subgrade reaction of 24,400 kN/m3 (90 lb/in3). Computations of the ultimate resistance, using the equations in Part II of the Technical Manual for response of the near-surface soils, yields 216.9 kN/m (1,240 lb/in.) for pu and for the soils at depth pu is 1,397.5 kN/m (7,987 lb/in.). The former value controls. The deflection at yu is equal to 3b/80 and is 0.034 m (1.34 in.). The value of pu is computed by multiplying 216.9 by the value of As (equal to 1.67, found from Figure 3.25, Part III of the Technical Manual) and becomes 362 kN/m (2,069 lb/in.). These values confirm the last four values in the output for p shown in the computer listing. The value of ym is b/60 and is 0.01523 meter (0.6 inch). The value of pm is found from Bsps and is found to be 260 kN/m (490 lb/in.) (reading a value of Bs = 1.20 from Figure 3.26, Part III, of the Technical Manual). This value confirms another point on the computer output. By referring to the curves giving the characteristic shape of the p-y curves for sand, it can be seen that two significant points on the p-y curve have been confirmed. Other points can be checked, but it will be assumed here that those points are also correct. 6-3-6 Check of Mechanics

The values of soil resistance that are listed in the computer output were plotted as a function of depth along the pile, and the plot is shown in Figure 6.3. The squares were counted

74

Chapter 6 – Validation and the forces that were computed from the area under the curve are shown in the figure. The following check was made of the summation of the forces in the horizontal direction. ∑Fh = 445 − 657 + 227 − 15 = 0 The forces are in equilibrium, which is quite fortuitous in view of the lack of precision in the procedure for numerical integration. The next step is to make a check of the position of the point of the maximum moment. As shown in Figure 6.3, the curve of soil resistance was integrated numerically and the position of zero shear (where the area under the soil-resistance curve is 445 kN [100 kips]) was at approximately 2.8 m (9.18 ft) from the top of the pile. The output in the appendix shows that the depth to zero shear force is between 2.71 m (8.9 ft) and 2.88 m (9.45 ft), which confirms the results of the numerical integration. To obtain a rough check of the value of the maximum moment, the centroid of the area under the curve equal to 445 kN (100 kips) is assumed to be approximately 1.8 m (6 ft) from the top of the pile or 1.0 m (3.3 ft) from the point of maximum moment; thus, the following equation can be written: Mmax = (445)(2.8) - (445)(1.0) Mmax = 806 m-kN (594 ft-kips) The tabulated value of the maximum moment in the output file on Section 6.3.10 is 711 m-kN (524 ft-kips), and the rough check shown above is considered to be acceptable. The next step in ing the mechanics is to make an approximate solution for the deflection. Several assumptions are made, as will be seen. Figure 6.3 shows that zero deflection occurs at depths of approximately 4.9 m (16 ft) and 10.9 m (36 ft) (where the soil resistance is zero), so the assumption is made that a zero slope exists in the deflection curve at midway between these two points, or at a depth of 7.9 meters (26 feet). The deflection at the top of the pile can be computed by taking moments of the M/EI diagram about the top and down to the point of zero slope. In order to simplify the computations, a further assumption is made that concentrated loads can be used to obtain the moment diagram instead of the distributed loads. Referring to Figure 6.3, the concentrated loads to be used in the analysis are the Pt of 445 kN (100 kips), a resisting load of 657 kN (148 kips) at approximately 2.2 m (7.2 ft) from the top of the pile, and a resisting load of 165 kN (37 kips) at approximately 6.8 m (22.3 ft) from the top of the pile. The following equation results: The listing of the output text in Section 6.3.10 shows yt to be 0.0134 meters (0.52 inch). The agreement is startling, in view of the assumptions that were made.

75

Chapter 6 – Validation

Figure 6.3 Plot of soil resistance versus depth

This computation completes the checking of the mechanics of the output from a computer run. While the results are not fully definitive, there is ample reason to trust the coding if a proper selection is made of a computer, the number of increments for a particular run, and the value of the tolerance used for concluding the iterations. 6-3-7 Use of Non-Dimensional Curves

Another type of verification can be made by using the p-y curves as tabulated by the computer. These curves should be checked by the engineer to be sure that they are accurate. Then nondimensional curves can be employed to solve the problem. These curves are presented by Reese and Matlock (1956) and in some detail in a document published by the Federal Highway istration (Reese, 1986). 6-3-8 Concluding Comments on Verification

The above paragraphs present some procedures that can be used for ing the accuracy of the output from the computer. The point cannot be made too strongly that the engineer should make verification a priority in working with LPile 6. The , if desired, may easily perform some of the elementary computations shown in this chapter. With regard to the static equilibrium of the lateral force on a single pile, the values of soil resistance can be computed and plotted along the length of the pile. With the lateral loads at the top of the pile, a check on the equilibrium of lateral forces can be made. A satisfactory check has been made by estimation; a more comprehensive check can be made by use of numerical 76

Chapter 6 – Validation integration of the distributed loads. The program will also conduct such checks internally to ensure the force equilibrium. The final internal check relates to the computed movement of the system. The first step is to refer to the computer output to confirm that the distributed load (soil resistance) and the distributed deflections along the length of the pile are consistent with the p-y curves that were input. If equations were used to compute the values of p and y, it is necessary to interpret the equations at a sufficient number of points to shown that the soil criteria for lateral load was followed. The second step with respect to lateral load is to employ the diagram is Step 1 and to use principles of mechanics to ascertain that the deflection of the individual piles was computed correctly. While employing the steps shown above have confirmed the internal functioning of Program LPile Plus, the application of the program to results of field experiments is useful. The book by Reese & Van Impe (2001)1 presents a discussion of the development of the methods used in Program LPile and applies the methods to several cases. Although the program has been used with apparent success in many analyses, new information is being developed and new versions may be written from time to time. No warranty, expressed or implied, is offered as to the accuracy of results from the program. The program should not be used for design unless caution is exercised in interpreting the results and independent calculations are available to the general correctness of the results. All s are requested to inform ENSOFT, INC. of any errors that are found in the coding for study and correction. 6-3-9 Input Data for Verification Problem 6-3-10 Output Data for Verification Problem

77

Chapter 7 Line-by-Line Guide for Input The input file for LPile Version 6 is a ASCII text file. The data file is updated with the latest data contained in the data editing dialogs of LPile immediately before every analysis is made. The computation functions in LPile begin by reading the input data file. The general format is a series of key words that denote the start of a section of data. The key words may be entered in any order, but the order of input in each section must follow a specific sequence. The content of the input data file is designed to be easily understandable by the .

7-1 Key Words for Input Data File The following table lists the key words that define sections of data. The key words may be entered in any order. Table 7-1 Key Words for Definition of Input Data Input Command Word TITLE OPTIONS SECTIONS AXIAL THRUST LOADS SOIL LAYERS TIP SHEAR PILE BATTER AND SLOPE LRFD LOADS LRFD FACTORS AND CASES LOADING SOIL MOVEMENTS GROUP EFFECT FACTORS P-Y OUTPUT DEPTHS END

Data Type Defined by Key Word Title lines for data file (five lines) Program and analysis options Pile section and material properties Axial thrust loads used in nonlinear moment-curvature computations Soil profile dimension and soil properties used for p-y curve computations Tip shear vs. lateral tip movement data Pile batter and slope data Unfactored loads for LRFD analysis Load and resistance factors and load combination data Pile-head boundary conditions and loading data for conventional analysis Soil movement vs. depth data Group effect factors (p and y-multiplier) data Output depths for reported p-y curves Terminates reading of input data

7-1-1 TITLE Command

The TITLE keyword indicated that the following five lines of text are entered for the problem title. Entering fewer or more than five lines of text will result in an execution error and input of data is stopped.

78

Chapter 7 – Line-by-Line Guide for Input By default, the following lines of text are predefined in LPile, but may be changed to anything that the wishes to enter. The default lines are : Project Name:: Job Number: Client: Engineer: Description: 7-1-2 OPTIONS Command

The OPTIONS keyword begins the definition of program options selected by the . Some options are either Yes or No options and the other options require numerical input. The order of the options must be in the following sequence. Options Keyword (without spaces) Units UseLRFD ComputeKmatrix UseTipShear UseSoilMovement UsePYModifiers ComputeEIOnly

Loading

IterationsLimit ConvergenceTolerance NumberPileIncrements PrintSummaryOnly PrintIncrement

Defines Option for

Permissible Values

Engineering units Perform LRFD analysis Compute pile-head stiffness matrix component values Use tip shear resistance curve Include loading by soil moveements Use p-y modifiers for group action Compute nonlinear momentcurvature values and nominal moments capacity only

USCS, SI YES, NO

Number of cycles of loading

Maximum number of iterations for numerical solution Convergence tolerance for numerical solution Number of pile increments for numerical solution Print summary tables only Printing increment for pile response

79

YES, NO YES, NO YES, NO YES, NO YES, NO If for static loading enter: “STATIC”, followed by 5 spaces, then “1” If for cyclic loading enter: “CYCLIC” 100 = default value, 1,000 = maximum value 1.0×10−5 inches = default value 100 = default, 40 = minium, 500 = maximum YES, NO 1 = default value

Chapter 7 – Line-by-Line Guide for Input

PrintPYCurves ComputeInteration

Report p-y curves at specified depths Compute interaction diagram only

YES, NO YES, NO

7-1-3 SECTIONS Command

The SECTIONS keyword begins the definition of structural properties of the pile to be analyzed. The order of the input data must be in the following sequence. The input data consists of one or more numbers followed by an optional comment. Data written by LPile will be followed by a comment that both describes the input data and the engineering units of the data. SECTIONS Line Number 1 2

3

Properties for rectangular sections 3.0.1.1 Section dimension 3.0.1.2 Section dimension 3.0.1.3 Section dimension 3.0.2.1 Concrete property 3.0.2.2 Concrete property

3.0.2.3 Concrete property 3.0.2.4 Concrete property

3.0.3.1 Rebar properties

Input Value Total Number of Sections, 1 = minimum, 10 = maximum Section number Section Type 0 = rectangular, 1 = drilled shaft, 2 = drilled shaft with casing, 3 = drilled shaft with casing and core, 4 = steel pipe 5 = circular solid prestressed pile, 6 = circular hollow prestressed pile 7 = square solid prestressed pile, 8 = square hollow prestressed pile, 9 = octagonal solid prestressed pile, 10= octagonal hollow prestressed pile, 11 = elastic pile, 12 = elastic-plastic pile 13 = pile with -defined nonlinear bending properties Lines 3.0 Length of section, ft or m Section depth, inches or mm Section width inches or mm Compressive strength of concrete, psi or kPa Maximum coarse aggregate size, in. or mm “Use default concrete tensile strength” (provided for future program option) “Use internal stress-strain curve for concrete” (provided for future program option) Rebar number options: For no rebar enter: “No rebar” If not Section 1 and rebar data same as above section, enter : “Rebar Arrangement Same As 80


3.0.3.2 Rebar arrangement

3.0.3.2.1 3.0.3.2.2 3.0.3.2.3 3.0. 3.2.4 3.0. 3.2.5 3.0. 3.2.6 3.0. 3.2.7 3.0.3.2.8 3.0.3.3.1 3.0.3.3.2 3.0. 3.3.3 3.0. 3.3.4.1 3.0.3.3.4.2 3.0.3.3.4.3 3.0.3.3.4.4 3.0.3.3.4.5 3.0.3.3.4.6 Properties for Drilled Shaft Sections 3.1.1.1 Section dimension 3.1.1.2 Section dimension 3.1.1.3 Section dimension 3.1.2.1 Concrete property 3.1.2.2 Concrete property 3.1.2.3 Concrete property 3.1.2.4 Concrete property 3.1.3.1 Rebar properties

Section Above” If Section 1 or rebar not same as above section enter: “Rebar Arrangement Same As Section Above” If rebar in circular pattern, enter: “Rebar in circle”, and follow by Lines 3.0.2.3.1 through 3.0.3.2.8. If rebar in noncircular pattern, enter: “Rebar in noncircular pattern”, and follow by Lines 3.0.3.3.1 through 3.0.3.3.4.6 Yield stress of bars, psi or kPa Young’s modulus of bars, psi or kPa Number of bars or bundles, maximum of 300 single bars, 150 2-bar bundles, or 100 3-bar bundles Number of bars in bundle, 1 to 3 Bar diameter, inches or mm Bar area, sq. in. or sq. mm Rebar clear cover, inches or mm Rebar circle offset from centroid of section, inches or mm Yield stress of bars, psi or kPa Young’s modulus of bars, psi or kPa Number of bars, Repeat line 3.0.3.3.4.1 through 3.0.3.3.4.6 for all bars in noncircular arrangement Bar identification number Bar size index number Bar diameter, inches or mm Bar area, sq. in. or sq. mm Bar X-coordinate Bar Y-coordinate Lines 3.1 Length of section, ft or m Section diameter, inches or mm Section width inches or mm Compressive strength of concrete, psi or kPa Maximum coarse aggregate size, in. or mm, “Use default concrete tensile strength” (provided for future program option) “Use internal stress-strain curve for concrete” (provided for future program option) Rebar number options: For no rebar enter: “No rebar” If not Section 1 and rebar data same as above

81



3.1.3.2.1 Bar property 3.1.3.2.2 Bar property 3.1.3.2.3 Bar property 3.1.3.2.4 Bar property 3.1.3.2.5 Bar property 3.1.3.2.6 Bar property 3.1.3.2.7 Bar property 3.1. 3.2.8 Bar property 3.1.3.3.1 Bar property 3.1.3.3.2 Bar property 3.1. 3.3.3 Bar property 3.1. 3.3.4.1 Individual bar property 3.1.3.3.4.2 Individual bar property 3.1.3.3.4.3 Individual bar property 3.1.3.3.4.4 Individual bar property 3.1.3.3.4.5 Individual bar property 3.1.3.3.4.6 Individual bar property Properties of Drilled Shafts with Casing 3.2.1.1 Section dimension 3.2.1.2 Section dimension 3.2.1.3 Section dimension 3.2.1.4 Casing property 3.2.1.5 Casing property 3.2.2.1 Concrete property 3.2.2.2 Concrete property 3.2.2.3 Concrete property 3.2.2.4 Concrete property

section, enter : “Rebar Arrangement Same As Section Above” If Section 1 or rebar not same as above section enter: “Rebar Arrangement Same As Section Above” If rebar in circular pattern, enter: “Rebar in circle”, and follow by Lines 3.1.2.3.1 through 3.1.3.2.8. If rebar in noncircular pattern, enter: “Rebar in noncircular pattern”, and follow by Lines 3.1.3.3.1 through 3.1.3.3.4.6 Yield stress of bars, psi or kPa Young’s modulus of bars, psi or kPa Number of bars or bundles, maximum of 300 single bars, 150 2-bar bundles, or 100 3-bar bundles Number of bars in bundle, 1 to 3 Bar diameter, inches or mm Bar area, sq. in. or sq. mm Rebar clear cover, inches or mm Rebar circle offset from centroid of section, inches or mm Yield stress of bars, psi or kPa Young’s modulus of bars, psi or kPa Number of bars, Repeat line 3.1.3.3.4.1 through 3.1.3.3.4.6 for all bars in noncircular arrangement Bar identification number Bar size index number Bar diameter, inches or mm Bar area, sq. in. or sq. mm Bar X-coordinate Bar Y-coordinate Lines 3.2 Length of section, ft or m, Section diameter, inches or mm Casing wall thickness, inches or mm Yield stress of casing, psi or kPa Young’s modulus of casing, psi or kPa Compressive strength of concrete, psi or kPa Maximum coarse aggregate size, in. or mm, “Use default concrete tensile strength” (provided for future program option) “Use internal stress-strain curve for concrete” (provided for future program option)

82




3.2.3.2.1 Bar property 3.2.3.2.2 Bar property 3.2.3.2.3 Bar property 3.2.3.2.4 Bar property 3.2.3.2.5 Bar property 3.2.3.2.6 Bar property 3.2.3.2.7 Bar property 3.2. 3.2.8 Bar property 3.2.3.3.1 Bar property 3.2.3.3.2 Bar property 3.2. 3.3.3 Bar property 3.2. 3.3.4.1 Individual bar property 3.2.3.3.4.2 Individual bar property 3.2.3.3.4.3 Individual bar property 3.2.3.3.4.4 Individual bar property 3.2.3.3.4.5 Individual bar property 3.2.3.3.4.6 Individual bar property Properties for Drilled Shafts with Casing and Core 3.3.1.1 Section dimension 3.3.1.2 Section dimension 3.3.1.3 Section dimension 3.3.1.4 Casing property 3.3.1.5 Casing property 3.3.1.6 Core property 3.3.1.7 Core property

Rebar number options: For no rebar enter: “No rebar” If not Section 1 and rebar data same as above section, enter : “Rebar Arrangement Same As Section Above” If Section 1 or rebar not same as above section enter: “Rebar Arrangement Same As Section Above” If rebar in circular pattern, enter: “Rebar in circle”, and follow by Lines 3.2.2.3.1 through 3.2.3.2.8. If rebar in noncircular pattern, enter: “Rebar in noncircular pattern”, and follow by Lines 3.2.3.3.1 through 3.2.3.3.4.6 Yield stress of bars, psi or kPa Young’s modulus of bars, psi or kPa Number of bars or bundles, maximum of 300 single bars, 150 2-bar bundles, or 100 3-bar bundles Number of bars in bundle, 1 to 3 Bar diameter, inches or mm Bar area, sq. in. or sq. mm Rebar clear cover, inches or mm Rebar circle offset from centroid of section, inches or mm Yield stress of bars, psi or kPa Young’s modulus of bars, psi or kPa Number of bars, Repeat line 3.2.3.3.4.1 through 3.2.3.3.4.6 for all bars in noncircular arrangement Bar identification number Bar size index number Bar diameter, inches or mm Bar area, sq. in. or sq. mm Bar X-coordinate Bar Y-coordinate Lines 3.3

Length of section, ft or m, Section diameter, inches or mm Casing wall thickness, inches or mm Yield stress of casing, psi or kPa Young’s modulus of casing, psi or kPa Core diameter, inches or mm Core wall thickness, inches or mm

83

Chapter 7 – Line-by-Line Guide for Input 3.3.1.8 Core property 3.3.1.9 Core property 3.3.2.1 Concrete property 3.3.2.2 Concrete property 3.3.2.3 Concrete property 3.3.2.4 Concrete property



3.3.3.2.1 Bar property 3.3.3.2.2 Bar property 3.3.3.2.3 Bar property 3.3.3.2.4 Bar property 3.3.3.2.5 Bar property 3.3.3.2.6 Bar property 3.3.3.2.7 Bar property 3.3. 3.2.8 Bar property 3.3.3.3.1 Bar property 3.3.3.3.2 Bar property 3.3. 3.3.3 Bar property 3.3. 3.3.4.1 Individual bar property 3.3.3.3.4.2 Individual bar property 3.3.3.3.4.3 Individual bar property 3.3.3.3.4.4 Individual bar property 3.3.3.3.4.5 Individual bar property 3.3.3.3.4.6 Individual bar property Properties for Steel Pipe Piles

Yield stress of core, psi or kPa Young’s modulus of core, psi or kPa Compressive strength of concrete, psi or kPa Maximum coarse aggregate size, in. or mm, “Use default concrete tensile strength” (provided for future program option) “Use internal stress-strain curve for concrete” (provided for future program option) Rebar number options: For no rebar enter: “No rebar” If not Section 1 and rebar data same as above section, enter : “Rebar Arrangement Same As Section Above” If Section 1 or rebar not same as above section enter: “Rebar Arrangement Same As Section Above” If rebar in circular pattern, enter: “Rebar in circle”, and follow by Lines 3.3.2.3.1 through 3.3.3.2.8. If rebar in noncircular pattern, enter: “Rebar in noncircular pattern”, and follow by Lines 3.3.3.3.1 through 3.3.3.3.4.6 Yield stress of bars, psi or kPa Young’s modulus of bars, psi or kPa Number of bars or bundles, maximum of 300 single bars, 150 2-bar bundles, or 100 3-bar bundles Number of bars in bundle, 1 to 3 Bar diameter, inches or mm Bar area, sq. in. or sq. mm Rebar clear cover, inches or mm Rebar circle offset from centroid of section, inches or mm Yield stress of bars, psi or kPa Young’s modulus of bars, psi or kPa Number of bars, Repeat line 3.3.3.3.4.1 through 3.3.3.3.4.6 for all bars in noncircular arrangement Bar identification number Bar size index number Bar diameter, inches or mm Bar area, sq. in. or sq. mm Bar X-coordinate Bar Y-coordinate Lines 3.4

84

Chapter 7 – Line-by-Line Guide for Input 3.4.1.1 Section dimension 3.4.1.2 Pipe pile property 3.4.1.3 Pipe pile property 3.4.1.4 Pipe pile property 3.4.1.5 Pipe pile property Properties for Circular Solid Prestressed Piles 3.5.1.1 Section dimension 3.5.1.2 Section dimension 3.5.2.1 Concrete property 3.5.2.2 Concrete property 3.5.2.3 Concrete property 3.5.2.4 Concrete property

3.5.3 Strand arrangement

3.5.3.1.1 Auto-arranged strand property

3.5.3.1.2 Auto-arranged strand property 3.5.3.1.3 Auto-arranged strand property 3.5.3.1.4 Auto-arranged strand property 3.5.3.1.5 Auto-arranged strand property 3.5.3.1.6 Auto-arranged strand property 3.5.3.1.7 Auto-arranged strand property

3.5.3.2.1 Manually-arranged strand property

3.5.3.2.2 Manually-arranged strand property 3.5.3.2.3 Manually-arranged strand property 3.5.3.2.4 Manually-arranged strand property 3.5.3.2.5 Manually-arranged strand property

3.5.3.2.6.1 Individual strand property

Length of section, ft or m Core diameter, inches or mm Core wall thickness, inches or mm Yield stress of core, psi or kPa Young’s modulus of core, psi or kPa Lines 3.5

Length of section, ft or m Section diameter, inches or mm Compressive strength of concrete, psi or kPa Maximum coarse aggregate size, in. or mm, “Use default concrete tensile strength” (provided for future program option) “Use internal stress-strain curve for concrete” (provided for future program option) If strands in arranged pattern, enter: “Autoposition strands”, and follow by Lines 3.5.3.1.1 through 3.5.3.1.8. If strands in non-arranged pattern, enter: “Manually-positioned strands”, and follow by Lines 3.5.3.2.1 through 3.5.3.2.6 Strand family type, enter 1 for Grade 250 Lolax strands, 2 for Grade 270 Lo-lax strands, 3 for Grade 300 strands, 4 for Grade 145 smooth bars, 5 for Grade 160 smooth bars, 6 for deformed bars Stand size index number Number of strands Prestressing force, lbs or kN Fraction of prestress loss, decimal Strand clear cover, inches or mm Strand pattern type, enter 0 for circle, 1 for square, 2 for weak square Strand family type, enter 1 for Grade 250 Lolax strands, 2 for Grade 270 Lo-lax strands, 3 for Grade 300 strands, 4 for Grade 145 smooth bars, 5 for Grade 160 smooth bars, 6 for deformed bars Stand size index number Number of strands, Prestressing force, lbs or kN Fraction of prestress loss, decimal Repeat Lines 3.5.3.2.6.1 through 3.5.3.2.6.5 for all strands Strand identification number

85

Chapter 7 – Line-by-Line Guide for Input 3.5.3.2.6.2 Individual strand property 3.5.3.2.6.3 Individual strand property 3.5.3.2.6.4 Individual strand property

Strand size index Strand X-coordinate Strand Y-coordinate

7-1-4 AXIAL THRUST LOADS Command

86

Chapter 7 – Line-by-Line Guide for Input 7-1-5 SOIL LAYERS Command

7-1-6 TIP SHEAR Command

7-1-7 PILE BATTER AND SLOPE Command

7-1-8 LRFD LOADS Command

7-1-9 LRFD FACTORS AND CASES Command

7-1-10 LOADING Command

7-1-11 SOIL MOVEMENTS Command

7-1-12 GROUP EFFECT FACTORS Command

7-1-13 P-Y OUTPUT DEPTHS Command

7-2 LRFD Data File The LRFD data file is used to store load and resistance factors in a format that also defines load case combinations and load case names. The purpose of this data file is to eliminate the need to input data that may be common to many analyses. The LRFD data file is a plain text (ASCII) file. The LRFD data file is read from the Options dialog (see page 15 for more information about the Options dialog).

87

Lpile 6 Manual, Version 1 1c1z3r

Overview 1s532p

More details 6h715l

Related Documents 2w1qw

Lpile 6 Manual, Version 1 1c1z3r

Lpile 2016 Manual 144p1j

Ensoft Lpile Plus 5.0 - Technical Manual 5b124u

New Quickset Manual Version 1 1 g1gs

Lpile Technical Manual 4a6v

Armcad 6 Manual 20uz

More Documents from "Daniyal Ahmad" 1k705u

Fstc Welcome Pack 2015 44135

Reclaim Your Heart Yasmin Mogahed_2 373313

Lpile 6 Manual, Version 1 1c1z3r

Project Use Case Description Final 2qy1c

Types Of School Management 5t191w

List Of Aircraft Engine Manufacturers 1y4iv