Lpi Stormaster Ese Air Terminal 4o4b2u

Lightning Protection System

LIGHTNING PROTECTION INTERNATIONAL PTY LTD Active in Industry

PROUD AUSTRALIAN MANUFACTURER

The LPI story Lightning Protection International Pty Ltd (LPI) is a fully Australian owned manufacturer and supplier of direct strike lightning protection, transient voltage surge suppression and earthing/grounding solutions. For many years, LPI have been providing specialist lightning protection advice to customers in some of the most lightning prone areas of the world. Our personnel have extensive experience in risk management, system design, training, installation, certification and commissioning of systems in a wide variety of industry groups.

2

LIGHTNING

LPI maintains a third party Quality Management System to AS/NZS ISO 9001:2008.

Our extensive experience has involved risk management, system design, training, certification and installation and commissioning in key industry groups such as: Telecommunications & Broadcasting

LPI’s range of products and services are exported from its head office and research facility (in Tasmania, Australia) and via regional offices worldwide.

•

Petrochemical, Oil & Gas

•

Highrise buildings and hotels –

The company has been recognized within Australia for its outstanding export successes and has been awarded several prestigious export awards.

•

P R OT E CT I O N

I N T E R N AT I O N A L

all types of structures Sporting centre and grounds – Golf courses, race tracks, stadiums •

Aviation – Civil & Military

•

Mining – Coal, Gold, Nickel, Iron, Copper, Bauxite, etc.

•

Industrial facilities of all kinds

•

Defence – communications, surveillance and storage of armaments

•

Power generation and distribution

•

Rail / transport systems

•

Monuments / Ecological sites

PTY

LT D .

>>

www.lpi .com .au

LIGHTNING PROTECTION INTERNATIONAL PTY LTD Lightning & the need of safety Lightning is one of the most devastating natural phenomena. There are many discharges during lightning storms and some of them can even reach hundreds of kilo amperes. The electrical discharges are a great hazard to people, animal, buildings and electronic equipments. The economic consequences of lightning are also very important; it can cause fire, stop production of a factory or interrupt critical processes. A direct lightning discharge lasts a very short time but the intensity is enough to provoke electrocution resulting in heart failure and causing burns of different degrees to the human beings. Lightning is a constant hazard where the buildings and equipments are becoming more complex and sensitive every day. One lightning strike discharge can damage the buildings and cause failures to the electronic devices inside the building and sometimes it may even results in fire and important economical losses. Until now, there is no device that can prevent lightning formation or lightning strikes. However, it is possible to create a path (divert) for the lightning discharge to the ground which will minimise the damage to the environment through a well designed Lightning Protection System (LPS). The lightning protection should be considered preferably during the initial stage of the building/structure design which has 4 basic objectives: Capture lightning.

Disperse lightning current in the ground quickly and safely.

Conduct lightning current to earth avoiding damage.

Avoid the secondary effects of lightning (surge/temperory overvoltages)

The phenomena of lightning During the formation of a cumulonimbus (cloud forming a towering mass with a flat base at fairly low altitude and often a flat top, as in thunderstorms), there is an increase of ionisation and a potential difference is generated between the thunder cloud and the ground, which gives rise to small discharges.

between the cloud and the ground. This object/structure will be hit with the lightning strike. The cloud charge will try to find the straightest/shortest path to earth and if this path is not controlled, damages can be severe.

FIGURE 1 Negatively charged stepped leader moves towards ground Launch of upstreamer from highest ground point as field intensification rises

Electrical effects: Damages/destruction to the electrical & electronic equipments. Abnormal rise in ground voltage and surges/transients can damage all the equipment connected to the electrical network.

As the electric field gains in strength, the descending leader breaks up the dielectric field in the air. Ultimately, this may break through the layers of dielectric field in the air and strike the surface via the upward propagating tracer from the surface. In normal conditions there is a balance between positive and negative charges in the atmosphere, where the ground is more negatively charged than the air and the elements placed on the ground. However, the formation of storm clouds creates a charge polarization; usually, the lower part of the cloud is charged negatively, inducing then a positive charge at the ground and other elements on it. The electric field at the atmosphere can reach kilovolts in a short span of time. When the electric field is high enough, the cloud starts discharging towards the ground. The path formed by this discharge is called “downward leader” and produces a very sharp variation of the electric field, causing the corona effect. One of these objects/structure will be forming the upward leader, which will move towards the downward leader thus forming the discharge path

LIGHTNING

P R OT E CT I O N

Electrodynamical effects: Structure/building damages. The conductors & equipments which falls within the vicinity of the flow of lightning current are submitted to mechanical strengths due to the magnetic field originated. This may cause deformations and rupture the conductors & equipments.

FIGURE 2 Stepped leader progresses towards ground Upstreamer is attracted towards stepped leader

Thermal effects: Lightning strikes can lead to fires. Heat dissipation by the Joule effect can even cause fires. Effects on living beings: Electrocutions and burns. Currents ing through during a short lapse are enough for electrocution risk by respiratory or cardiac arrest. Further burn risk appears.

FIGURE 3

Induction effects: Within a variable electromagnetic field, induced currents appear in every conductor.

Leader and streamer meet to form ionised path for lightning discharge

I N T E R N AT I O N A L

The consequences of all these effects are important economical losses because of the damages in buildings and equipment due to lightning strike. Lightning can cause service interruptions, stops production processes or force to switch off and on again the utility machinery if the control equipment is affected by lightning.

PTY

LT D .

>>

www.lpi .com .au

3

LPI STORMASTER ESE AIR TERMINAL LPI 4-Step Approach to Lightning Protection

The Stormaster ESE range LPI Early Streamer Emission (ESE) air terminals in both Anodised Aluminium and Stainless Steel.

It is the strategic aim of our company to be able to provide a complete packaged solution. LPI has identified 4 key steps when considering the complete approach to lightning protection, ask for our LPI 4 Step approach to lightning protection.

Ordering Code: XX: Available in 15,30,50 and 60 YY: Bank for Gold (anodised aluminium) model, SS for stainless steel model. ZZ: Blank for standard model (to FRP Mast), GI for 2 inch BSP GI Pipe adaptor.

Our System design approach includes Definition and provision of area protection

Certified Performance As one of the leading companies in the field of lighting protection, LPI has invested heavily in field and laboratory testing as part of its ongoing commitment to research and development.

Creation of a bonded earthing system Protection of mains power lines Protection of signal, data and communication lines:

LPI Stormaster ESE The LPI Stormaster (Early Streamer Emission) range of terminals provides a safe and efficient system for the protection of your facility from direct lightning strikes.

How does the LPI Stormaster ESE Terminal work?

Throughout the product development of the Stormaster ESE the proto-type models were subjected to intense testing under high voltage conditions. Following further refinements the Stormaster terminals were subjected to final testing by an independently accredited test laboratory which com-

The LPI Stormaster ESE terminal captures The Stormaster ESE air terminal uses the lightning energy at a preferred point. the naturally occurring electrical field to complete the timely release of an upward streamer. This process provides for a safe and efficient method of controlling dangerous lightning energy at a preferred point. As a thunderstorm gathers overhead, the ambient electrical field surrounding the Stormaster ESE begins to rise in voltage. Upon the approach of a downward leader towards the protected area, there is a rapid increase in the electric field which initiates the triggering of an upward streamer from the Stormaster ESE terminal. The early initiation allows for a larger or enhanced area of protection to be provided by the Stormaster ESE in comparison to a conventional rod, in accordance with NF C 17-102. With the release of the upward streamer from the finial tip earlier than other competing structural points, the Stormaster ESE terminal becomes a preferred point for the capture of the lightning discharge within the protected area.

4

LIGHTNING

P R OT E CT I O N

I N T E R N AT I O N A L

pleted testing in full compliance with the French National Standard NF C 17-102. The final testing of Stormaster ESE terminals showed effective performance as defined in this Standard. LPI Stormaster ESE lightning air terminal is tested & certified from RI (Central Power Research Institute), Bangalore, Government of India.

PTY

LT D .

>>

www.lpi .com .au

LPI STORMASTER ESE AIR TERMINAL Protection Performance

PROTECTION RADIUS (M) - (Rp) h = height of Stormaster terminal

h(2D - h) +

4

5

6

10

15 20 45 60

Stormaster 15 SS

13

25

32

32 33

34 35 35 35

Stormaster 30 SS

19

28

48

48 49

50 50 50 50

Stormaster 50 SS

28

55

68

69 69

70 70 70 70

Stormaster 60 SS

32

64

79

79 79

80 80 80 80

above area to be protected (m)

The protection radius (Rp) of a Stormaster ESE terminal is calculated using the following formula as defined by the French National Standard NF C 17-102. Rp (h) =

2

Protection Level 1 (High Protection)

T(2D + T) for h 5m where:

The following key parameters determine the calculation of Rp.

Protection Level 2 (Medium Protection)

•

Stormaster 15 SS

18

36

45

46 49

52 55 60 60

Stormaster 30 SS

25

50

63

64 66

68 71 75 75

Stormaster 50 SS

35

69

86

87 88

90 92 95 95

Stormaster 60 SS

40

78

97

97 99 101 102 105 105

Stormaster 15 SS

20

41

51

52 56

60 63 73 75

Stormaster 30 SS

28

57

71

72 75

77 81 89 90

Stormaster 50 SS

38

76

95

96 98 100 102 110 110

Stormaster 60 SS

44

87 107 107 109 111 113 120 120

•

T as established during the test. Stormaster - ESE-15 SS = T (μs) 15 Stormaster - ESE-30 SS = T (μs) 30 Stormaster - ESE-50 SS = T (μs) 50 Stormaster - ESE-60 SS = T (μs) 60 h = actual height of Stormaster terminal above the area to be protected (m). D (in m) depends on the selected level of protection, protection levels are specified in annex B of the standard NF C 17-102. D = 20m for protection level 1 (High Protection) D = 45m for protection level 2 (Medium protection) D = 60m for protection level 3 (Standard protection)

Advantages of the Stormaster ESE Terminal

Lightning Strike Recorder (LSR1)

A typical Stormaster ESE installation consists of a single Stormaster ESE terminal with an enhanced area of protection and downconductors connected to a dedicated earthing system designed to have a low inpedance to lightning. 1.

LPI’s Stormaster ESE system is simple to install and requires no special maintenance.

2.

LPI’s Stormaster ESE system is a cost effective solution for providing your lightning protection whilst providing superior safety.

3.

The Stormaster ESE range of terminals have been fully tested in accordance with NF C 17-102 in a high voltage laboratory.

LPI personnel and its associates have been involved in a number of field trials throughout lightning prone regions of the world. This experience has extended throughout such countries as Australia, India, Indonesia, Sri Lanka, USA and South Korea.

P R OT E CT I O N

LPI have developed a LSR which is designed for easy mounting on a downconductor to effectively count the number of lightning srikes captured by the Stormaster ESE Terminal. When the lightning rod receive an impact of the lightning strike, discharge counter detects the energy dissipated by the down conductor, thereby incrementing the number. The LSR1 operates by sensing current by means of an inductive pick up loop. With the voltage impulse detected by the current transformer (CT) a trigger to the pulse counter then turns the counter to the lightning event.

LPI has an ongoing commitment to Research and Development.

LIGHTNING

Protection Level 3 (Standard Protection)

The equipment does not require either external or internal power supply, as it is electromechanical and uses the power of the induced current dissipated through the down conductor. It must be placed on the down-conductor above the control/testlink t and, in all cases, 2mtrs above the ground. Its use is not obligatory but is highly recommended by NF C 17-102 standard. Features

I N T E R N AT I O N A L

PTY

7 Digits

Up to 9,999,999 counts

IP 67 enclosure

Testable using LSR-Tester

LT D .

>>

www.lpi .com .au

5

LPI STORMASTER ESE AIR TERMINAL

IMPORTANT: Stormaster ESE terminal to be a minimum of 2 metres above the highest point of the building. Recommended clearance height = 5 metres

LPI GUY KIT ORDERING CODE: GUYKIT-4M GUYKIT-4M-SS GUYKIT-7M GUYKIT-7M-SS LPI CABLE TIES ORDERING CODE: SS-CABTIE-STD SS-CABTIES-L

If installing either a radial 25mm x 3mm Earth Rods clamped to earthing system or grid Copper Tape Copper Tape type earthing system it Tape Clamp is recommended that all earthing conductors be installed at a depth of Earth Pit between 500mm and 750mm (recommended) Earth Rods Each Radial Trench Clamp with a maximum depth is treated with of 1000mm. In order Earth Enhancing Compound to further assist in LPI Copper Tape 25 x 3mm improving the earth typically 3 Radial lengths of 10m, resistance of the system, 500mm depth with a maximum depth of 1000m it is recommended that the excavated soil of poor quality (rocky/sandy) shall be replaced with the soil of a good quality (garden loam) prior to backfilling the trench.

LPI HIGH VOLTAGE SHIELDED CABLE ORDERING CODE: HVSC-PM

Key components of a lightning earth include:

LPI STORMASTER ESE AIR TERMINAL ORDERING CODE: STORMASTER-ESE-60 STORMASTER-ESE-50 STORMASTER-ESE-30 STORMASTER-ESE-15 ADD-GI TO END OF PRODUCT CODE FOR CONNECTION TO 2” BSP LPI UPPER TERMINATION KIT ORDERING CODE: UTERMKIT-Mk2 UTERM-FACTOUTSIDE-Mk2 LPI MAST ORDERING CODE: FRP-2M FRP-3M FRP-4M LPI INLINE COUPLING ORDERING CODE: ILCOUPLING

LPI LOWER MAST ASSEMBLY WITH BASE ORDERING CODE: ALUMB-3M ALUMB-4M ALUMB-5M ALUMB-6M

Earth Rods Copper bonded (threaded or unthreaded), Solid Copper or Stainless Steel LPI Resistance Lowering Compound (LPI RESLO) The requirement for a low resistance is extremely important with the installation of any earthing system. LPI’s RESLO provides the ability to dramatically reduce soil resistivity even in soils with average electrical conductivity. LPI RESLO is supplied in 10 Kgs packaged bags to suit the site application.

LPI SADDLES AND FIXINGS ORDERING CODE: SAD FIX

LPI HIGH VOLTAGE SHIELDED CABLE ORDERING CODE: HVSC-PM LPI LIGHTING STRIKE RECORDER ORDERING CODE: LSR1

LPI INSPECTION PIT ORDERING CODE: EPIT-P EPIT-D EPIT-C LPI LOWER TERMINATION KIT ORDERING CODE: LTERMKIT EARTH ENHANCING COMPOUND ORDERING CODE: GRIP-10 RESLO-10 LOW EARTH-20

LPI EARTHING SYSTEM TYPICAL PRODUCTS REQUIRED FOR RADIAL LP EARTH (EG): 4 X CBER1214 4 X RTC253 1 X EPIT-P 1 X GRIP-10 20 X FL6T253C

Lightning Protection Earthing The installation of a radial earthing arrangement is recommended for each lightning protection earth, the radial earthing configuration provides an effective means for the safe dissipation of the lightning energy into the ground mass. All individual lightning earths should be bonded together in a ring earth arrangement to minimise ground loops and potential differences under transient conditions. Compliance to NF C17-102 requires an earth DC resistance reading of less than 10 ohms for the lightning earths.

6

LIGHTNING

RESLO comprises specifically selected compounds, which possess excellent electrical conductivity. When RESLO is mixed with water and poured around the earthing system and surrounding soil, the powder and water react to form a hardened mass within an earthing system. RESLO will not wash away under seasonal conditions and therefore provides a permanent presence in working to improve and maintain the integrity of an earthing system. Given that RESLO does not wash away the requirement to re-treat the soil as is the case with other enhancing compounds is eliminated. LPI Ground Resistance Improvement Powder (LPI GRIP) The requirement for a low resistance is extremely important with the installation of any earthing system. LPI’s GRIP provides the ability to substantially reduce soil resistivity in soils of the poorest electrical conductivity such as rocky ground or sandy soils. LPI GRIP is supplied in two kit sizes - A 10 Kgs kit comprises two 5 Kg containers; one 5 Kg kit contains a copper compound whilst the other 5 Kg kit holds a mix of compounds which assist in the mixing process (Hardener). When GRIP is mixed with water and poured around the earthing system and surrounding soil, the powder and water react to form a gelatinous hygroscopic mass which forms an integral part of an earthing system, this effectively increases the surface area of the earthing system in with the surrounding soil. GRIP will not wash away under seasonal conditions and therefore provides a permanent presence in working to improve and maintain the integrity of an earthing system. Given that GRIP does not wash away the requirement to re-treat the soil is eliminated. P R OT E CT I O N

I N T E R N AT I O N A L

PTY

LT D .

>>

www.lpi .com .au

LPI STORMASTER ESE AIR TERMINAL Downconductors

NF C 17 - 102 (2011) The New Standard

NF C17-102 (2011) requires the installation of two downconductors for each installed ESE air terminal, with one downconductor permitted to use electrically continuous natural components of the structure.

NF C17 - 102 is written specifically to ensure compliance with regard to the testing, applications and installation of ESE terminal. The new standard issued in 2011 is deemed to be applicable and structures of any height and for the protection of open areas. The previous version of the standard was first published in 1995 has been cancelled by the French standards organisations UTE and conformity with that version ceased in September 2012. NF C17-102 (2011) includes much more stringent requirements when compared to the 1995 version. The main differences are as follows: 1. There are now four protection levels rather than the previous three levels. 2. There are two new enhanced sub-levels for protection level I (level I+ and I++) 3. Protection of structures taller than 60 metres is now allowed and there are special rules with regard to strike interception and downconductors. The top 20% of the building needs to be protected. 4. Some simple rules regarding downconductors, essentially two are needed, but one of them can be the natural components of the structure. 5. The earlier ban on coaxial insulated downconductors has been removed, but any use of insulated conductors has to follow the separation distance requirements per the IEC 62305 standards.

High Voltage Shielded Cable (HVSC)

Flat tapes Bare, Tinned & PVC Covered

Ultimate direct strike lightning protection as installed across 65 countries around the world

PVT Coated and bare stranded copper cable

Disclaimer LPI maintains a policy of on-going product development, specifications are subject to change without notice.

Downconductor Fixings and Connectors

Application detail, illustrations and schematic drawings are representative only and should be used as guides. It should be noted that 100% protection level for direct strike lightning, lightning detection and surge and transient protection equipment is not possible and cannot be provided due to the lightning discharge process being a natural atmospheric event.

LIGHTNING

P R OT E CT I O N

I N T E R N AT I O N A L

PTY

LT D .

>>

www.lpi .com .au

7

OUR CLIENTS LIST

Distributed by:

ALLIED POWER SOLUTIONS (ISO 9001:2008 & UL listed LPS installer) T - 4, 5 & 6, Third Floor Pankaj Plaza - 3, I.P. Extn., Patparganj Delhi - 110 092 (INDIA) Tel: +91 11 2224 7322 Email: [email protected] Web: www.alliedpowersolutions.org

PO Box 379 Kingston, Tasmania, Australia 7051 49 Patriarch Drive, Huntingfield, Tasmania, Australia 7055

Telephone: Australia: 03 6281 2477 International: + 61 3 6281 2480 Facsimile: + 61 3 6229 1900 Email: [email protected] Web: www.lpi.com.au

BENGALURU Mob: +91 98869 63195, 98860 08218

8

LIGHTNING

P R OT E CT I O N

I N T E R N AT I O N A L

PTY

LT D .

>>

www.lpi .com .au