Furnace Transformers 63x3p
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report 445h4w
Overview 1s532p
& View Furnace Transformers as PDF for free.
More details 6h715l
- Words: 4,268
- Pages: 9
Electrical Engineering of Arc Furnaces Transformers Furnace Transformer Types & Design Characteristics Dipl.Ing.Univ. Egon Kirchenmayer Siemens AG, PTD T LC Nuremberg ()
Siemens Energy & Automation
Loaded Transformer Loading the secondary winding with a current I2 causes a magnetic flux of that winding. This flux is linked also with the primary winding and tends to reduce the total flux seen by the primary winding. Therefore a compensating current I1 will flow in the primary winding producing a compensating flux. The ampere turns of both windings are nearly equal: I 1 ×w1 = I 2 ×w 2 and
Furnace Transformers 1. Mode of Functioning of a Transformer
F I1 I2
U1
U2
Fx F
dΦ dt
(Law of Induction)(1)
If there is no consumer connected to the terminals of the secondary winding, the secondary current will be zero (I2=0) and the transformer is in the so called no load operation. The magnetic flux which flows in this case trough the secondary winding is the same as in the primary winding: Φ . The variation in time of this flux induces in the secondary winding the voltage U02:
U 02
dΦ = w2 × dt
After elimination of
(2)
dΦ from the formulae (1) dt
and (2) we come to the conclusion that the ratio of the no load voltages corresponds to the ratio of the turns of the windings:
U 01 w1 = =ü U 02 w 2 ü is the transformation ratio.
Furnace Transformers
1
The flux between both windings is called stray flux Φ x. The bigger the stray flux is, the weaker is the magnetic coupling between both windings. The secondary winding is now linked with the main flux Φ and with the stray flux Φ x.
U 2 = w2 ×
The mode of functioning will be illustrated based on a simplified single phase model with two windings placed on an iron core. A sinusoidal ac-voltage source U01 is connected to the terminals of the inner winding (Which is placed directly on the core). A magnetic flux Φ will then flow trough the core. The variation in time of this flux multiplied with the number of turns corresponds to the applied voltage at the terminals:
U 01 = w1 ×
I1 w2 1 = = I 2 w1 ü
d (Φ − Φ x ) dΦ dΦ = w2 × − w2 × x dt dt dt
Using equation (1):
w2 ×U 01 − U x 2 (3) w1 dΦ = w 2 × x is the short circuit voltage dt
U2 = U x2
of the transformer related to the secondary winding. This voltage is related normally to the no load voltage and is given in Percent.:
ux =
U x2 %] ×100[ U 02
Equation (3) can be expressed by an equivalent circuit or by voltage phasors as follows: Ux2
w2/w1U01
I2 w2/w1U01
Ux2 U2
X2
U2 I2
The short circuit reactance is calculated based on the short circuit voltage, the no load voltage and the rated power as follows:
X =
ux U2 × 0 [ Ω] 100 % S n
The short circuit resistance is calculated based on the short circuit loss and the corresponding current as follows:
R=
PCu [Ω ] 3 ×I 2
Transformatorenwerk Nürnberg
2. Electrical Characteristics of Furnace Transformers
variation of short circuit voltage and short circuit impedance with the tapping range:
Furnace Transformers have to adapt the electrical energy to the requirements of the electrical furnaces. The energy will be absorbed normally from a medium voltage system (30, 20 or 10 kV) and transformed to a range of 100 to 1400 V. If a special type of transformer is chosen, it can be connected also directly to the 110 kV or even to the 220 kV system.
0,40
1,00 Secondary Voltage(p.u.) Secondary current
The variation in time of the currents is influenced by the mode of operation of the arc furnace. The variation of power covers the whole range between no load and short circuit of the electrodes including a superimposed inrush current:
Power Short circuit voltage Short circuit impedance related to U2
The secondary voltage can be regulated in a ratio of 2:1 to 3:1 or even more. As higher the power of a furnace transformer, as higher is normally the maximum value of the secondary voltage.
3. Types of Furnace Transformers Current at different moments of time within the first seconds after the first ignition of the arc in a new batch.
3.1. AC-Furnace Transformers
3.1.1.Variable-Flux Voltage Regulation The furnace transformer contains in this case one active part. The voltage regulation is done by changing the number of turns in the high voltage winding by means of a tap changer. As the supplying voltage on the high voltage side remains unchanged, the flux density will change with changing numbers of turns.(Variable-Flux voltage regulation).
Currents in the three phases, two minutes after the first arc ignition in a new batch.
Currents in the three phases, 40 minutes after the first arc ignition in a new batch. Furnace Transformers are characterised by a typical definition of power, a great tapping range and very high currents on the low voltage side. Usually, a range of constant power and a range of constant current are defined, while the secondary voltage decreases and the primary (applied) voltage remains unchanged. In some cases the range of constant power is omitted. In those cases the rating is defined by a range of constant secondary current only. Furnace transformers show a typical Furnace Transformers
2
The high voltage winding can be star or delta connected. The low voltage winding can have a star-, delta- or open-circuit connection. Transformatorenwerk Nürnberg
This type of furnace transformer has the most economic design, as only one active part is required. (see also 3.1.4). The range of application is limited due to the maximum height of the primary voltage as the transient over-voltages in the tapping winding increase considerably with higher system voltages. The voltage regulation is normally done in unequal steps due to the variable flux regulation. A coarse equalisation can be achieved in some cases using different numbers of turns per step.
3.1.2.Regulation With Intermediate Circuit This type of furnace transformer consists of two active parts enclosed normally in the same tank: a main transformer and a booster transformer. The main transformer contains the high voltage winding, a part of the low voltage winding and the regulating winding. The booster transformer contains the second part of the low voltage winding (connected in series with the first part) and a high voltage winding, fed by the regulating winding of the main transformer. The regulating winding of the main transformer and the high voltage winding of the booster transformer form the intermediate circuit. Mp
winding of the main transformer. Therefore the power of the booster transformer has to be increased. The opened s of the switchgear are stressed by double the voltage of the intermediate circuit. All these effects have to be considered in the design stage. An additional advantage of this type is that equal voltage steps can be achieved along the whole tapping range. There are also no limitations in choosing the size of the tapping range. The example given above contains a also a tertiary winding which is suitable for connecting an external filter or power factor correction equipment. This leads to cost optimisation of such equipment especially in the case of high system voltages.
3.1.3.Regulation With Transformer
an
Auto
This type contains two active parts, an auto transformer with regulating winding and a furnace transformer which are located normally in a common tank. Furnace transformer
Mp
Auto transformer
This type can be connected directly to a high voltage system. Main transformer Booster transformer
mp
This type is normally connected to high voltage systems. Furnace transformers made by Siemens which are connectable to the 110 kV system as well as to the 220 kV system are in service since decades. The voltage of the intermediate circuit can be chosen by the designer. As higher it is, as more sophisticated is the insulation system. But as the current is lower at higher voltages, a less expensive tap changer can be chosen. It is up to the designer to find the optimum. The switchgear can be included in the intermediate circuit. Due to the reduced voltage of the intermediate circuit, a less expensive switchgear can be chosen. If the switchgear is open, the booster transformer will be magnetised from its low voltage winding. This implies, that the booster transformer is designed for the voltage level of the low voltage Furnace Transformers
3
In this case, an intermediate circuit is formed by the common winding and the regulating winding of the auto transformer and the high voltage winding of the furnace transformer. The voltage of this intermediate circuit can be chosen by the designer. As higher this voltage is, as lower is the current, which determines the size and cost of the tap changer. The built in power of the auto transformer decreases with a lower transformation ratio but the cost of the insulation system increases. A tertiary winding can be foreseen to connect a filter or a power factor correction equipment.
3.1.4.Comparison Types
of
the
Three
The possible range of application of the three types has been described above. The following comparison is done from an economical point of view. The built in power of a furnace transformer is normally much higher than the rated power. This is determined by the special power demand of such a Transformatorenwerk Nürnberg
transformer and by the chosen concept. The comparison is done based on the same tapping range for all three types e.g.: Umax/Uconstant/Umin = 1 / 0,8 / 0,5. The ratio between built in power and rated power for the given tapping range is as follows: Variable flux regulation: 1,63 Intermediate circuit regulation: 1,44 Regulation with auto transformer: 1,56 The best ratio is achieved in the case of Intermediate circuit regulation, followed by the regulation with auto transformer. As these types consist of two active parts, the manufacturing effort is much higher than in the case of the variable flux regulation. If the transformer is connected to the medium voltage system, the variable flux regulation leads to the most economical design. If the transformer is connected to the high voltage system, the available manufacturing facilities and the figures given above will determine the chosen type.
3.1.5.Other Characteristics Other characteristics of some special types of furnace transformers are given below: No load star delta switchover of the high voltage winding of furnace transformers with variable flux voltage regulation is used to reduce the built in power in cases where big tapping ranges are required. If for instance a voltage range Umax/Umin = 1 / 0,33 is foreseen, the built in power is only 1,49 times the rated power if such a switchover connection is used. (compare also 3.1.4). An individual regulation of each phase can be realised. In this case, a zero sequence flux can occur. Special measures have to be taken in this case. Furnace transformers for ac-furnaces can be built also as single phase units. In the case of the so called Knappsack-connection, three single phase units are arranged symmetrically around the furnace. Due to the geometrical symmetry the impedance of the three phases is nearly the same. This leads to a uniform load of the three phases. This advantage is compensated by higher manufacturing cost and greater content of material of the single phase units compared with a three phase unit.
Furnace reactor with attached tap changer to be included in the main transformer tank. 3.2. Transformers for DC-Furnaces This type of transformer contains some elements from conventional rectifier transformers (used in electrolysis plants or dc-drives) and other elements from ac-furnace transformers. Transformers for dc-furnaces can be built to be connected to medium voltage systems and to high voltage systems. All kinds of voltage regulation mentioned above can be foreseen in principle for this type of transformer too. In many cases rectifiers with thyristors are used. In this case the voltage regulation can be done via thyristors and there is only a small tap changing equipment necessary or it can be even omitted. If a tap changer is foreseen, it is normally a no load tap changer.
Furnace reactors are used mainly in connection with furnace transformers of high rating to regulate the impedance of the plant (in order to achieve a more stable arc). The reactance of such reactors can be changed in 3 to 7 steps with the use of a no load tap changer. The more expensive solution with an onload tap changer can also be chosen. The reactor can normally be included in the transformer tank.
The both low voltage windings are connected to the rectifier. They are connected in star and delta reFurnace Transformers
4
Transformatorenwerk Nürnberg
spectively. A special 6 pulse connection has been developed by Siemens in order to minimise the flicker phenomenon. This connection requires two low voltage windings, both connected in star or both connected in delta. The amount of harmonics caused by the arc are less in the case of dc-furnaces, as the dc-arc burns smoother than the ac-arc. But in this case the additional harmonics produced by the rectifier have to be considered in the design of the transformer (see also 4.2.1). The influence of the harmonics generated by the rectifier can be reduced by increasing the pulse order. In the case of a bridge connection of the rectifier, a 12 pulse system can be achieved by using one low voltage winding in star connection and one other in delta connection. By the use of phase shifting windings 24 pulse-, 36 pulse- and even higher pulse order connections can be realised. The short circuit current is lower than in the case of ac-furnaces, because of the current limiting properties of the rectifier.
4. Mechanical Design of Furnace Transformers 4.1. Transformer Core The core carries the main magnetic flux of the transformer. The form of the core is the same as used in regular power transformers. The core consists nowadays of grain oriented magnetic steel of the HIB class. A favourable distribution of loss and temperature in the core is achieved by using the so called step lap stacking of the core sheets. The maximum flux density has to be chosen taking into the voltage harmonics produced by the rectifier, which can lead to an increase of the loss and temperatures of the core. If the voltages of each phase are regulated individually, a zero sequence flux can occur. If there is no delta winding on the core, a return path for the zero sequence flux has to be foreseen. Due to the currents and forces produced in the windings of furnace transformers, vibrations are transmitted from the windings to the core. Core sheets and other parts of the core have to be secured against movement. The core of furnace transformers for dc-furnaces can be built in double tier form. The differential flux can be carried by intermediate yokes which are placed between the middle of the core legs.
High forces are generated in the windings due to the high magnitude of these currents. Many measures are required in the design stage, during manufacturing and in the winding treatment process in order to control these forces. Some keywords for this are: detailed calculation of stresses and forces, careful selection of the materials used, proper dimensioning of all s inside and outside the windings, securing all parts against movement, manufacturing with very small tolerances, proper drying and pressing of the windings in order to eliminate the plastic component of the windings, excellent symmetry of the windings. The influence of the harmonics of the current has to be considered in the thermal design of the windings. This applies especially in the case of dcfurnace transformers, where the stray losses can be doubled or even tripled by the harmonics of the current. Traditionally loss evaluation has not the same importance for furnace transformers than for power transformers. Therefore higher current densities are chosen in the case of furnace transformers. Therefore a very effective cooling is required. In many cases the OD-cooling (oil-directed) is used, where the oil is directly pumped trough the windings.
4.2.2.Design of the Windings The conductors used for high voltage windings are bare conductors or continuously transposed conductors for higher ratings. Layer windings are used in the case of lower voltage levels, otherwise disc windings are used. Disc windings can be interleaved at the line end of the windings in order to control the impulse voltage distribution inside the windings. The conductors used for regulating windings can be also bare conductors or continuously transposed conductors. The control of impulse voltages and resonant voltages is of major importance for regulating windings. Especially switching operations can cause resonant frequencies, which can be in the range of the resonant frequencies of tapping windings. The voltages which can occur in this cased have to be controlled in order to assure the reliability of the transformer.
4.2. Windings of Furnace Transformers 4.2.1.Stresses Frequent short circuits of the electrodes produce high magnitudes of the load currents (about 2.5 times the rated current). The shape of the currents can be distorted due to the nonliniarity of the arc resistance. The frequent reignition of the arc can lead to inrush currents with high magnitudes. Furnace Transformers
5
Transformatorenwerk Nürnberg
The leads of the regulating winding are connected to the tap changer.
If clamps of copper are used, they can be connected in parallel and in series.
The types of conductors used in the low voltage windings are mainly continuously transposed conductors, cylinders of copper, or clamps of copper. In the past also bare conductors have been used.
Low voltage leads can carry currents up to 100 kA. Therefore special measures are required to assure a proper current distribution within the windings and leads.
4.3. Low Voltage Connections of Furnace Transformers Bushings consisting of flat bars of copper can be used up to currents of 60 kA.. A transformer with such bushings arranged on the top of the active part (cover of the tank) can be seen in the figure above. For higher currents water cooled bushings consisting of bent copper tubes are used (see the picture below).
If continuously transposed cables are used, the low voltage windings consist normally of many groups of transposed cables which are connected in parallel by the use of huge bars of copper.
Bushings can be placed on the tank wall or on the cover of the tank. The bushings are arranged very often in the form of a triangle. This makes it possible that the leads to the furnace can be arranged symmetrically in order to achieve nearly equal impedances and currents in all the phases.
One or two turns can be realised by the use of cylinders of copper.
Furnace Transformers
6
Transformatorenwerk Nürnberg
4.4. Cooling
protection of terminals with surge arresters and protecting parts of the transformer windings by voltage limiting elements.
5. Limitations of the Rated Power Furnace transformers have been built up to a maximum power of 150 MVA and up to maximum low voltage currents of 100 kA. The following chart shows which secondary voltages are normally chosen for transformers of different power ratings. The graph is based on data of transformers manufactured in the Siemens Factory in Nürnberg. The range of the ladle furnace transformers with rated power up to 50 MVA can be recognised in the graph. The outer cooling system consists normally of oilwater coolers by which the heat can be led away in a space saving manner.
U2max=f(Sn) 1,6
4.5. Tap Changing Equipment The voltage can be regulated normally by an onload tap changer or by a no load tap changer. The s of tap changers for furnace transformers are made normally of material of higher quality. The s may have bigger diameters than normally. The special circumstances of furnace operation have to be considered for the selection of the switching capacity. Due to the increased number of switching operations and due to the fact that high amplitudes of current have to be switched, the oil in the switching compartment of onload tap changers will be deteriorated faster. Therefore it is advisable to use oil filters.
4.6. Screening The stray field of the windings and of the leads which carry high currents can induce eddy currents in metallic parts. These eddy currents can cause high losses and temperatures. These losses and temperatures can be controlled by the use of magnetic and nonmagnetic screens.
1,4 1,2 1 0,8 0,6 0,4 0,2 0 0
50
100
150
200
Rated Power [MVA]
The r.m.s value of the secondary currents is in the range of 20 to 100 kA. The current is limited due to the maximum load of the electrodes used in furnaces. The dependence of secondary currents from the rated power is shown in the following chart, which is based on transformers manufactured in the Siemens Factory in Nürnberg. I2max=f(Sn)
4.7. Protection Against Overvoltages
120,00
Switching overvoltages can be generated when switching-off furnace transformers. They can be high when loads are switched off but can be relevant also when the unloaded transformer is switched-off.
100,00
Resonant events are of major importance. If frequencies are generated which correspond to the resonant frequencies of the transformer, high overvoltages can be generated inside the transformer. Resonant events can be started by reignitions of switches during load-switch-off or by arc interruptions in service. The protection of transformers against resonant overvoltages can be done as follows: choosing different resonant frequencies for the system and for the transformer, using R-C damping elements, Furnace Transformers
7
80,00 60,00 40,00 20,00 0,00 0
50
100
150
200
Rated Power [MVA]
Transformatorenwerk Nürnberg
It is possible, from our point of view to build furnace transformers of higher rated power in the future. The secondary current of furnace transformers is limited due to the following factors: • The width of transformer windings is limited due to the losses produced by the stray field. • Available space for the low voltage bushings • Current distribution in the low voltage bushings A maximum secondary current of 120 kA can be reached based on the limitations given above if a conventional design is used. The primary current is limited by the tap changers which are available. Tap changers for furnace transformers are available up to a maximum current of 3000 A. The rated power of furnace transformers is limited based on this consideration as follows: Primary Voltage [kV] 10 20 30
Rated Power [MVA] HV-Delta HV Star 90 50 180 100 270 150
This consideration is not valid for transformers with intermediate circuit because the current of the intermediate circuit can be chosen individually. If a rated secondary voltage of 1500 V and a maximum secondary current of 80 kA would be chosen, the rated power of the transformer would be:
S n = 1500V ×80 kA × 3 = 210 MVA Such a transformer could be built with a primary voltage of 30 kV. Also if the primary voltage would be 110 kV or 220 kV the transformer could be built with intermediate circuit or with directly connected autotransformer. Other limitations can be: • Maximum dimensions and weight with regard to the transportation possibilities • Production capabilities of the manufacturers
6.
Rated Power constant up to Vector group Rated primary voltage Secondary voltage maximum minimum steps Secondary current Furnace Transformers
105 MVA 837 V Dd0 30 kV 960 V 550 V 18 73 kA
7% 10,5% 18,2%
The short circuit reactance can be calculated based on the short circuit voltage. It will be related to the secondary voltage: At tap position 18:
2 u k U 022 7% (0,96 kV ) X2 ≈ ⋅ = ⋅ = 0,61mΩ 100% S 100% 105 MVA X 2 (Tap _ position _ 13)= 0,67 mΩ X 2 (Tap _ position _ 1)= 0,79mΩ
Although the short circuit voltage increases with higher tap positions, the reactance seen from the secondary terminals remains nearly unchanged. The resistance related to the secondary terminals can be derived from the short circuit loss (approx. 520 kW on tap position 18):
R2 =
PCu 520 kW = = 0,044 mΩ 2 2 3 ×I 3 ×(63kA)
The transformer is equipped with a reactor connected in series to the high voltage winding, with an onload tap changer. The reactance of this reactor related to the primary terminals as well as to the secondary terminals(reduced by the square of the transformation rate ü2) is given in the table below: Tap pos. reactor: 10 9 5 1 Primary side delta 0Ω 0,56Ω 2,63Ω 4,93Ω Primary side, star 0Ω 0,19Ω 0,88Ω 1,64Ω Secondary side 0,19 0,90 1,68 0Ω Tap position 18 mΩ mΩ mΩ Secondary side 0,064 0,29 0,55 0Ω Tap position 1 mΩ mΩ mΩ The effect of the reactor on the secondary side is greater if the transformation ratio is lower, i.e. if the secondary voltage is higher.
Bibliography
[1]
Feyertag, H.: Transformatoren für Lichtbogenöfen, Klepzig Fachberichte 82 (1974) Heft 4
[2]
Heindl, H.: Ofen- und Gleichrichtertransformatoren, ETZ-A, Heft 3, 1977
[3]
Timm, K.: Elektrotechnik des Lichtbogenofens, Seminar vom 19. Bis 22. Oktober 1999 in Saalfeld
Example of a Furnace Transformer
The technical data of a furnace transformer with variable flux voltage regulation will be discussed below, based on the data of the rating plate (see Appendix 1 and 2).
8
Short circuit voltage Tap position 18 Tap position 13 Tap position 1
Author: Dipl.Ing.Univ. Egon Kirchenmayer R&D Department Siemens-Transformatorenwerk Nürnberg
Transformatorenwerk Nürnberg
Siemens Energy & Automation
Loaded Transformer Loading the secondary winding with a current I2 causes a magnetic flux of that winding. This flux is linked also with the primary winding and tends to reduce the total flux seen by the primary winding. Therefore a compensating current I1 will flow in the primary winding producing a compensating flux. The ampere turns of both windings are nearly equal: I 1 ×w1 = I 2 ×w 2 and
Furnace Transformers 1. Mode of Functioning of a Transformer
F I1 I2
U1
U2
Fx F
dΦ dt
(Law of Induction)(1)
If there is no consumer connected to the terminals of the secondary winding, the secondary current will be zero (I2=0) and the transformer is in the so called no load operation. The magnetic flux which flows in this case trough the secondary winding is the same as in the primary winding: Φ . The variation in time of this flux induces in the secondary winding the voltage U02:
U 02
dΦ = w2 × dt
After elimination of
(2)
dΦ from the formulae (1) dt
and (2) we come to the conclusion that the ratio of the no load voltages corresponds to the ratio of the turns of the windings:
U 01 w1 = =ü U 02 w 2 ü is the transformation ratio.
Furnace Transformers
1
The flux between both windings is called stray flux Φ x. The bigger the stray flux is, the weaker is the magnetic coupling between both windings. The secondary winding is now linked with the main flux Φ and with the stray flux Φ x.
U 2 = w2 ×
The mode of functioning will be illustrated based on a simplified single phase model with two windings placed on an iron core. A sinusoidal ac-voltage source U01 is connected to the terminals of the inner winding (Which is placed directly on the core). A magnetic flux Φ will then flow trough the core. The variation in time of this flux multiplied with the number of turns corresponds to the applied voltage at the terminals:
U 01 = w1 ×
I1 w2 1 = = I 2 w1 ü
d (Φ − Φ x ) dΦ dΦ = w2 × − w2 × x dt dt dt
Using equation (1):
w2 ×U 01 − U x 2 (3) w1 dΦ = w 2 × x is the short circuit voltage dt
U2 = U x2
of the transformer related to the secondary winding. This voltage is related normally to the no load voltage and is given in Percent.:
ux =
U x2 %] ×100[ U 02
Equation (3) can be expressed by an equivalent circuit or by voltage phasors as follows: Ux2
w2/w1U01
I2 w2/w1U01
Ux2 U2
X2
U2 I2
The short circuit reactance is calculated based on the short circuit voltage, the no load voltage and the rated power as follows:
X =
ux U2 × 0 [ Ω] 100 % S n
The short circuit resistance is calculated based on the short circuit loss and the corresponding current as follows:
R=
PCu [Ω ] 3 ×I 2
Transformatorenwerk Nürnberg
2. Electrical Characteristics of Furnace Transformers
variation of short circuit voltage and short circuit impedance with the tapping range:
Furnace Transformers have to adapt the electrical energy to the requirements of the electrical furnaces. The energy will be absorbed normally from a medium voltage system (30, 20 or 10 kV) and transformed to a range of 100 to 1400 V. If a special type of transformer is chosen, it can be connected also directly to the 110 kV or even to the 220 kV system.
0,40
1,00 Secondary Voltage(p.u.) Secondary current
The variation in time of the currents is influenced by the mode of operation of the arc furnace. The variation of power covers the whole range between no load and short circuit of the electrodes including a superimposed inrush current:
Power Short circuit voltage Short circuit impedance related to U2
The secondary voltage can be regulated in a ratio of 2:1 to 3:1 or even more. As higher the power of a furnace transformer, as higher is normally the maximum value of the secondary voltage.
3. Types of Furnace Transformers Current at different moments of time within the first seconds after the first ignition of the arc in a new batch.
3.1. AC-Furnace Transformers
3.1.1.Variable-Flux Voltage Regulation The furnace transformer contains in this case one active part. The voltage regulation is done by changing the number of turns in the high voltage winding by means of a tap changer. As the supplying voltage on the high voltage side remains unchanged, the flux density will change with changing numbers of turns.(Variable-Flux voltage regulation).
Currents in the three phases, two minutes after the first arc ignition in a new batch.
Currents in the three phases, 40 minutes after the first arc ignition in a new batch. Furnace Transformers are characterised by a typical definition of power, a great tapping range and very high currents on the low voltage side. Usually, a range of constant power and a range of constant current are defined, while the secondary voltage decreases and the primary (applied) voltage remains unchanged. In some cases the range of constant power is omitted. In those cases the rating is defined by a range of constant secondary current only. Furnace transformers show a typical Furnace Transformers
2
The high voltage winding can be star or delta connected. The low voltage winding can have a star-, delta- or open-circuit connection. Transformatorenwerk Nürnberg
This type of furnace transformer has the most economic design, as only one active part is required. (see also 3.1.4). The range of application is limited due to the maximum height of the primary voltage as the transient over-voltages in the tapping winding increase considerably with higher system voltages. The voltage regulation is normally done in unequal steps due to the variable flux regulation. A coarse equalisation can be achieved in some cases using different numbers of turns per step.
3.1.2.Regulation With Intermediate Circuit This type of furnace transformer consists of two active parts enclosed normally in the same tank: a main transformer and a booster transformer. The main transformer contains the high voltage winding, a part of the low voltage winding and the regulating winding. The booster transformer contains the second part of the low voltage winding (connected in series with the first part) and a high voltage winding, fed by the regulating winding of the main transformer. The regulating winding of the main transformer and the high voltage winding of the booster transformer form the intermediate circuit. Mp
winding of the main transformer. Therefore the power of the booster transformer has to be increased. The opened s of the switchgear are stressed by double the voltage of the intermediate circuit. All these effects have to be considered in the design stage. An additional advantage of this type is that equal voltage steps can be achieved along the whole tapping range. There are also no limitations in choosing the size of the tapping range. The example given above contains a also a tertiary winding which is suitable for connecting an external filter or power factor correction equipment. This leads to cost optimisation of such equipment especially in the case of high system voltages.
3.1.3.Regulation With Transformer
an
Auto
This type contains two active parts, an auto transformer with regulating winding and a furnace transformer which are located normally in a common tank. Furnace transformer
Mp
Auto transformer
This type can be connected directly to a high voltage system. Main transformer Booster transformer
mp
This type is normally connected to high voltage systems. Furnace transformers made by Siemens which are connectable to the 110 kV system as well as to the 220 kV system are in service since decades. The voltage of the intermediate circuit can be chosen by the designer. As higher it is, as more sophisticated is the insulation system. But as the current is lower at higher voltages, a less expensive tap changer can be chosen. It is up to the designer to find the optimum. The switchgear can be included in the intermediate circuit. Due to the reduced voltage of the intermediate circuit, a less expensive switchgear can be chosen. If the switchgear is open, the booster transformer will be magnetised from its low voltage winding. This implies, that the booster transformer is designed for the voltage level of the low voltage Furnace Transformers
3
In this case, an intermediate circuit is formed by the common winding and the regulating winding of the auto transformer and the high voltage winding of the furnace transformer. The voltage of this intermediate circuit can be chosen by the designer. As higher this voltage is, as lower is the current, which determines the size and cost of the tap changer. The built in power of the auto transformer decreases with a lower transformation ratio but the cost of the insulation system increases. A tertiary winding can be foreseen to connect a filter or a power factor correction equipment.
3.1.4.Comparison Types
of
the
Three
The possible range of application of the three types has been described above. The following comparison is done from an economical point of view. The built in power of a furnace transformer is normally much higher than the rated power. This is determined by the special power demand of such a Transformatorenwerk Nürnberg
transformer and by the chosen concept. The comparison is done based on the same tapping range for all three types e.g.: Umax/Uconstant/Umin = 1 / 0,8 / 0,5. The ratio between built in power and rated power for the given tapping range is as follows: Variable flux regulation: 1,63 Intermediate circuit regulation: 1,44 Regulation with auto transformer: 1,56 The best ratio is achieved in the case of Intermediate circuit regulation, followed by the regulation with auto transformer. As these types consist of two active parts, the manufacturing effort is much higher than in the case of the variable flux regulation. If the transformer is connected to the medium voltage system, the variable flux regulation leads to the most economical design. If the transformer is connected to the high voltage system, the available manufacturing facilities and the figures given above will determine the chosen type.
3.1.5.Other Characteristics Other characteristics of some special types of furnace transformers are given below: No load star delta switchover of the high voltage winding of furnace transformers with variable flux voltage regulation is used to reduce the built in power in cases where big tapping ranges are required. If for instance a voltage range Umax/Umin = 1 / 0,33 is foreseen, the built in power is only 1,49 times the rated power if such a switchover connection is used. (compare also 3.1.4). An individual regulation of each phase can be realised. In this case, a zero sequence flux can occur. Special measures have to be taken in this case. Furnace transformers for ac-furnaces can be built also as single phase units. In the case of the so called Knappsack-connection, three single phase units are arranged symmetrically around the furnace. Due to the geometrical symmetry the impedance of the three phases is nearly the same. This leads to a uniform load of the three phases. This advantage is compensated by higher manufacturing cost and greater content of material of the single phase units compared with a three phase unit.
Furnace reactor with attached tap changer to be included in the main transformer tank. 3.2. Transformers for DC-Furnaces This type of transformer contains some elements from conventional rectifier transformers (used in electrolysis plants or dc-drives) and other elements from ac-furnace transformers. Transformers for dc-furnaces can be built to be connected to medium voltage systems and to high voltage systems. All kinds of voltage regulation mentioned above can be foreseen in principle for this type of transformer too. In many cases rectifiers with thyristors are used. In this case the voltage regulation can be done via thyristors and there is only a small tap changing equipment necessary or it can be even omitted. If a tap changer is foreseen, it is normally a no load tap changer.
Furnace reactors are used mainly in connection with furnace transformers of high rating to regulate the impedance of the plant (in order to achieve a more stable arc). The reactance of such reactors can be changed in 3 to 7 steps with the use of a no load tap changer. The more expensive solution with an onload tap changer can also be chosen. The reactor can normally be included in the transformer tank.
The both low voltage windings are connected to the rectifier. They are connected in star and delta reFurnace Transformers
4
Transformatorenwerk Nürnberg
spectively. A special 6 pulse connection has been developed by Siemens in order to minimise the flicker phenomenon. This connection requires two low voltage windings, both connected in star or both connected in delta. The amount of harmonics caused by the arc are less in the case of dc-furnaces, as the dc-arc burns smoother than the ac-arc. But in this case the additional harmonics produced by the rectifier have to be considered in the design of the transformer (see also 4.2.1). The influence of the harmonics generated by the rectifier can be reduced by increasing the pulse order. In the case of a bridge connection of the rectifier, a 12 pulse system can be achieved by using one low voltage winding in star connection and one other in delta connection. By the use of phase shifting windings 24 pulse-, 36 pulse- and even higher pulse order connections can be realised. The short circuit current is lower than in the case of ac-furnaces, because of the current limiting properties of the rectifier.
4. Mechanical Design of Furnace Transformers 4.1. Transformer Core The core carries the main magnetic flux of the transformer. The form of the core is the same as used in regular power transformers. The core consists nowadays of grain oriented magnetic steel of the HIB class. A favourable distribution of loss and temperature in the core is achieved by using the so called step lap stacking of the core sheets. The maximum flux density has to be chosen taking into the voltage harmonics produced by the rectifier, which can lead to an increase of the loss and temperatures of the core. If the voltages of each phase are regulated individually, a zero sequence flux can occur. If there is no delta winding on the core, a return path for the zero sequence flux has to be foreseen. Due to the currents and forces produced in the windings of furnace transformers, vibrations are transmitted from the windings to the core. Core sheets and other parts of the core have to be secured against movement. The core of furnace transformers for dc-furnaces can be built in double tier form. The differential flux can be carried by intermediate yokes which are placed between the middle of the core legs.
High forces are generated in the windings due to the high magnitude of these currents. Many measures are required in the design stage, during manufacturing and in the winding treatment process in order to control these forces. Some keywords for this are: detailed calculation of stresses and forces, careful selection of the materials used, proper dimensioning of all s inside and outside the windings, securing all parts against movement, manufacturing with very small tolerances, proper drying and pressing of the windings in order to eliminate the plastic component of the windings, excellent symmetry of the windings. The influence of the harmonics of the current has to be considered in the thermal design of the windings. This applies especially in the case of dcfurnace transformers, where the stray losses can be doubled or even tripled by the harmonics of the current. Traditionally loss evaluation has not the same importance for furnace transformers than for power transformers. Therefore higher current densities are chosen in the case of furnace transformers. Therefore a very effective cooling is required. In many cases the OD-cooling (oil-directed) is used, where the oil is directly pumped trough the windings.
4.2.2.Design of the Windings The conductors used for high voltage windings are bare conductors or continuously transposed conductors for higher ratings. Layer windings are used in the case of lower voltage levels, otherwise disc windings are used. Disc windings can be interleaved at the line end of the windings in order to control the impulse voltage distribution inside the windings. The conductors used for regulating windings can be also bare conductors or continuously transposed conductors. The control of impulse voltages and resonant voltages is of major importance for regulating windings. Especially switching operations can cause resonant frequencies, which can be in the range of the resonant frequencies of tapping windings. The voltages which can occur in this cased have to be controlled in order to assure the reliability of the transformer.
4.2. Windings of Furnace Transformers 4.2.1.Stresses Frequent short circuits of the electrodes produce high magnitudes of the load currents (about 2.5 times the rated current). The shape of the currents can be distorted due to the nonliniarity of the arc resistance. The frequent reignition of the arc can lead to inrush currents with high magnitudes. Furnace Transformers
5
Transformatorenwerk Nürnberg
The leads of the regulating winding are connected to the tap changer.
If clamps of copper are used, they can be connected in parallel and in series.
The types of conductors used in the low voltage windings are mainly continuously transposed conductors, cylinders of copper, or clamps of copper. In the past also bare conductors have been used.
Low voltage leads can carry currents up to 100 kA. Therefore special measures are required to assure a proper current distribution within the windings and leads.
4.3. Low Voltage Connections of Furnace Transformers Bushings consisting of flat bars of copper can be used up to currents of 60 kA.. A transformer with such bushings arranged on the top of the active part (cover of the tank) can be seen in the figure above. For higher currents water cooled bushings consisting of bent copper tubes are used (see the picture below).
If continuously transposed cables are used, the low voltage windings consist normally of many groups of transposed cables which are connected in parallel by the use of huge bars of copper.
Bushings can be placed on the tank wall or on the cover of the tank. The bushings are arranged very often in the form of a triangle. This makes it possible that the leads to the furnace can be arranged symmetrically in order to achieve nearly equal impedances and currents in all the phases.
One or two turns can be realised by the use of cylinders of copper.
Furnace Transformers
6
Transformatorenwerk Nürnberg
4.4. Cooling
protection of terminals with surge arresters and protecting parts of the transformer windings by voltage limiting elements.
5. Limitations of the Rated Power Furnace transformers have been built up to a maximum power of 150 MVA and up to maximum low voltage currents of 100 kA. The following chart shows which secondary voltages are normally chosen for transformers of different power ratings. The graph is based on data of transformers manufactured in the Siemens Factory in Nürnberg. The range of the ladle furnace transformers with rated power up to 50 MVA can be recognised in the graph. The outer cooling system consists normally of oilwater coolers by which the heat can be led away in a space saving manner.
U2max=f(Sn) 1,6
4.5. Tap Changing Equipment The voltage can be regulated normally by an onload tap changer or by a no load tap changer. The s of tap changers for furnace transformers are made normally of material of higher quality. The s may have bigger diameters than normally. The special circumstances of furnace operation have to be considered for the selection of the switching capacity. Due to the increased number of switching operations and due to the fact that high amplitudes of current have to be switched, the oil in the switching compartment of onload tap changers will be deteriorated faster. Therefore it is advisable to use oil filters.
4.6. Screening The stray field of the windings and of the leads which carry high currents can induce eddy currents in metallic parts. These eddy currents can cause high losses and temperatures. These losses and temperatures can be controlled by the use of magnetic and nonmagnetic screens.
1,4 1,2 1 0,8 0,6 0,4 0,2 0 0
50
100
150
200
Rated Power [MVA]
The r.m.s value of the secondary currents is in the range of 20 to 100 kA. The current is limited due to the maximum load of the electrodes used in furnaces. The dependence of secondary currents from the rated power is shown in the following chart, which is based on transformers manufactured in the Siemens Factory in Nürnberg. I2max=f(Sn)
4.7. Protection Against Overvoltages
120,00
Switching overvoltages can be generated when switching-off furnace transformers. They can be high when loads are switched off but can be relevant also when the unloaded transformer is switched-off.
100,00
Resonant events are of major importance. If frequencies are generated which correspond to the resonant frequencies of the transformer, high overvoltages can be generated inside the transformer. Resonant events can be started by reignitions of switches during load-switch-off or by arc interruptions in service. The protection of transformers against resonant overvoltages can be done as follows: choosing different resonant frequencies for the system and for the transformer, using R-C damping elements, Furnace Transformers
7
80,00 60,00 40,00 20,00 0,00 0
50
100
150
200
Rated Power [MVA]
Transformatorenwerk Nürnberg
It is possible, from our point of view to build furnace transformers of higher rated power in the future. The secondary current of furnace transformers is limited due to the following factors: • The width of transformer windings is limited due to the losses produced by the stray field. • Available space for the low voltage bushings • Current distribution in the low voltage bushings A maximum secondary current of 120 kA can be reached based on the limitations given above if a conventional design is used. The primary current is limited by the tap changers which are available. Tap changers for furnace transformers are available up to a maximum current of 3000 A. The rated power of furnace transformers is limited based on this consideration as follows: Primary Voltage [kV] 10 20 30
Rated Power [MVA] HV-Delta HV Star 90 50 180 100 270 150
This consideration is not valid for transformers with intermediate circuit because the current of the intermediate circuit can be chosen individually. If a rated secondary voltage of 1500 V and a maximum secondary current of 80 kA would be chosen, the rated power of the transformer would be:
S n = 1500V ×80 kA × 3 = 210 MVA Such a transformer could be built with a primary voltage of 30 kV. Also if the primary voltage would be 110 kV or 220 kV the transformer could be built with intermediate circuit or with directly connected autotransformer. Other limitations can be: • Maximum dimensions and weight with regard to the transportation possibilities • Production capabilities of the manufacturers
6.
Rated Power constant up to Vector group Rated primary voltage Secondary voltage maximum minimum steps Secondary current Furnace Transformers
105 MVA 837 V Dd0 30 kV 960 V 550 V 18 73 kA
7% 10,5% 18,2%
The short circuit reactance can be calculated based on the short circuit voltage. It will be related to the secondary voltage: At tap position 18:
2 u k U 022 7% (0,96 kV ) X2 ≈ ⋅ = ⋅ = 0,61mΩ 100% S 100% 105 MVA X 2 (Tap _ position _ 13)= 0,67 mΩ X 2 (Tap _ position _ 1)= 0,79mΩ
Although the short circuit voltage increases with higher tap positions, the reactance seen from the secondary terminals remains nearly unchanged. The resistance related to the secondary terminals can be derived from the short circuit loss (approx. 520 kW on tap position 18):
R2 =
PCu 520 kW = = 0,044 mΩ 2 2 3 ×I 3 ×(63kA)
The transformer is equipped with a reactor connected in series to the high voltage winding, with an onload tap changer. The reactance of this reactor related to the primary terminals as well as to the secondary terminals(reduced by the square of the transformation rate ü2) is given in the table below: Tap pos. reactor: 10 9 5 1 Primary side delta 0Ω 0,56Ω 2,63Ω 4,93Ω Primary side, star 0Ω 0,19Ω 0,88Ω 1,64Ω Secondary side 0,19 0,90 1,68 0Ω Tap position 18 mΩ mΩ mΩ Secondary side 0,064 0,29 0,55 0Ω Tap position 1 mΩ mΩ mΩ The effect of the reactor on the secondary side is greater if the transformation ratio is lower, i.e. if the secondary voltage is higher.
Bibliography
[1]
Feyertag, H.: Transformatoren für Lichtbogenöfen, Klepzig Fachberichte 82 (1974) Heft 4
[2]
Heindl, H.: Ofen- und Gleichrichtertransformatoren, ETZ-A, Heft 3, 1977
[3]
Timm, K.: Elektrotechnik des Lichtbogenofens, Seminar vom 19. Bis 22. Oktober 1999 in Saalfeld
Example of a Furnace Transformer
The technical data of a furnace transformer with variable flux voltage regulation will be discussed below, based on the data of the rating plate (see Appendix 1 and 2).
8
Short circuit voltage Tap position 18 Tap position 13 Tap position 1
Author: Dipl.Ing.Univ. Egon Kirchenmayer R&D Department Siemens-Transformatorenwerk Nürnberg
Transformatorenwerk Nürnberg
Related Documents 2w1qw
Furnace Transformers 63x3p
December 2021 0
Furnace 3i2y1s
November 2021 0
Furnace 3i2y1s
May 2020 6
Transformers 304z5y
April 2022 0
Literatur Furnace 6a3d2k
December 2019 63