6.2.4.4 Packet Tracer - Configuring Ipv6 Static And Default Routes Instructions 1z3b3x

Packet Tracer - Configuring IPv6 Static and Default Routes Topology

IPv6 Addressing Table Device

Interface

IPv6 Address/Prefix

Default Gateway

G0/0

2001:DB8:1:1::1/64

N/A

S0/0/0

2001:DB8:1:A001::1/64

N/A

G0/0

2001:DB8:1:2::1/64

N/A

S0/0/0

2001:DB8:1:A001::2/64

N/A

S0/0/1

2001:DB8:1:A002::1/64

N/A

G0/0

2001:DB8:1:3::1/64

N/A

S0/0/1

2001:DB8:1:A002::2/64

N/A

PC1

NIC

2001:DB8:1:1::F/64

FE80::1

PC2

NIC

2001:DB8:1:2::F/64

FE80::2

PC3

NIC

2001:DB8:1:3::F/64

FE80::3

R1

R2

R3

Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure IPv6 Static and Default Routes Part 3: Connectivity

© 2013 Cisco and/or its s. All rights reserved. This document is Cisco Public.

Page 1 of 3

Packet Tracer - Configuring IPv6 Static and Default Routes

Background In this activity, you will configure IPv6 static and default routes. A static route is a route that is entered manually by the network in order to create a route that is reliable and safe. There are four different static routes used in this activity: a recursive static route; a directly attached static route; a fully specified static route; and a default route.

Part 1: Examine the Network and Evaluate the Need for Static Routing a. Looking at the topology diagram, how many networks are there in total? b. How many networks are directly connected to R1, R2, and R3? c.

How many static routes are required by each router to reach networks that are not directly connected?

d. Which command is used to configure IPv6 static routes?

Part 2: Configure IPv6 Static and Default Routes Step 1: Enable IPv6 routing on all routers. Before configuring static routes, we must configure the router to forward IPv6 packets Which command accomplishes this? Enter this command on each router.

Step 2: Configure recursive static routes on R1. Configure an IPv6 recursive static route to every network not directly connected to R1.

Step 3: Configure a directly attached and a fully specified static route on R2. a. Configure a directly attached static route from R2 to the R1 LAN. b. Configure a fully specific route from R2 to the R3 LAN.

Step 4: Configure a default route on R3. Configure a recursive default route on R3 to reach all networks not directly connected.

Step 5: static route configurations. a. Which command is used to the IPv6 configuration of a PC from the command prompt?

b. Which command displays the IPv6 addresses configured on a router's interface?

c.

Which command displays the contents of the IPv6 routing table?

Part 3: Network Connectivity Every device should now be able to ping every other device. If not, review your static and default route configurations.

© 2013 Cisco and/or its s. All rights reserved. This document is Cisco Public.

Page 2 of 3

Packet Tracer - Configuring IPv6 Static and Default Routes

Suggested Scoring Rubric Activity Section Part 1: Exam the Network and Evaluate the Need for Static Routing

Part 2: Configure IPv6 Static and Default Routes

Question Location

Possible Points

a-d

20

Part 1 Total

20

Step 1

5

Step 5

15

Part 2 Total

20

Packet Tracer Score

60

Total Score

100

© 2013 Cisco and/or its s. All rights reserved. This document is Cisco Public.

Earned Points

Page 3 of 3